child lock INFINITI G37 2012 User Guide

Black plate (55,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0647
Forward-facing — step 4
4. For child restraints that are equipped
with webbing-mounted attachments,
remove any additional slack from the
anchor attachments. Press downward
and rearward firmly in the center of the
child restraint with your knee to com-
press the vehicle seat cushion and
seatback while tightening the webbing
of the anchor attachments.
5. Tighten the tether strap according to
the manufacturer ’ s instructions to re-
move any slack. SSS0638
Forward-facing — step 6
6. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the LATCH attach-
ment path. The child restraint should
not move more than 1 inch (25 mm),
from side to side. Try to tug it forward
and check to see if the LATCH attach-
ment holds the restraint in place. If the
restraint is not secure, tighten the
LATCH attachment as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 7. Check to make sure the child restraint
is properly secured prior to each use. If
the child restraint is loose, repeat steps
1 through 6.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT
BELTS GUID-B0438CCC-C788-4E94-8FA4-DB4F26EE0A33
WARNING The three-point seat belt with Automatic
Locking Retractor (ALR) must be used when
installing a child restraint. Failure to use the
ALR mode will result in the child restraint
not being properly secured. The restraint
could tip over or be loose and cause injury
to a child in a sudden stop or collision. Also,
it can change the operation of the front
passenger air bag. See “ Front passenger air
bag and status light ” (P.1-49).
Safety — Seats, seat belts and supplemental restraint system
1-33

Black plate (57,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]SSS0651
Forward-facing — step 4
4. Pull the shoulder belt until the belt is
fully extended. At this time, the seat
belt retractor is in the Automatic Lock-
ing Retractor (ALR) mode (child restraint
mode). It reverts to Emergency Locking
Retractor (ELR) mode when the seat belt
is fully retracted. SSS0652
Forward-facing — step 5
5. Allow the seat belt to retract. Pull up on
the shoulder belt to remove any slack
in the belt. SSS0653
Forward-facing — step 6
6. Remove any additional slack from the
seat belt; press downward and rear-
ward firmly in the center of the child
restraint with your knee to compress
the vehicle seat cushion and seatback
while pulling up on the seat belt.
7. Tighten the tether strap according to
the manufacturer ’ s instructions to re-
move any slack.
Safety — Seats, seat belts and supplemental restraint system
1-35

Black plate (58,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]1-36 Safety — Seats, seat belts and supplemental restraint system SSS0641
Forward-facing — step 8
8. After attaching the child restraint, test
it before you place the child in it. Push
it from side to side while holding the
child restraint near the seat belt path.
The child restraint should not move
more than 1 inch (25 mm), from side to
side. Try to tug it forward and check to
see if the belt holds the restraint in
place. If the restraint is not secure,
tighten the seat belt as necessary, or
put the restraint in another seat and
test it again. You may need to try a
different child restraint. Not all child
restraints fit in all types of vehicles. 9. Check to make sure the child restraint
is properly secured prior to each use. If
the seat belt is not locked, repeat steps
2 through 8.
SSS0676
Forward-facing — step 10
10. If the child restraint is installed in the
front passenger seat, place the ignition
switch in the ON position. The front
passenger air bag status light
should illuminate. If this light is not
illuminated, see “ Front passenger air
bag and status light ” (P.1-49). Move
the child restraint to another seating
position. Have the system checked by
an INFINITI retailer.
After the child restraint is removed and the
seat belt is fully retracted, the ALR mode
(child restraint mode) is canceled.

Black plate (61,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]LRS0464
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated.
The instructions in this section apply to
booster seat installation in the rear seats
or the front passenger seat. Booster seat installation GUID-F402278F-CB4D-47C2-8CA5-E6E93C16F092
CAUTION Do not use the lap/shoulder belt Automatic
Locking Retractor (ALR) mode when using a
booster seat with the seat belts.
Refer to all Warnings and Cautions in the
“ Child safety ” , “ Child restraints ” and
“ Booster seats ” sections earlier in this
section before installing a child restraint.
Follow these steps to install a booster seat
in the rear seat or in the front passenger
seat: SSS0640
1. If you must install a booster seat in the
front seat, move the seat to the rear-
most position.
2. Position the booster seat on the seat.
Only place it in a forward-facing direc-
tion. Always follow the booster seat
manufacturer ’ s instructions.
Safety — Seats, seat belts and supplemental restraint system
1-39

Black plate (130,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-52 Instruments and controls GUID-EC46BDB9-5A5F-4FC9-A9F0-5555C039C450
POWER WINDOWS GUID-B5DC4A3B-BDA9-404F-9E56-B523D30545FC
WARNING. Make sure that all passengers have their
hands, etc. inside the vehicle while it is
in motion and before closing the win-
dows. Use the window lock switch to
prevent unexpected use of the power
windows.
. Do not leave children unattended inside
the vehicle. They could unknowingly
activate switches or controls and be-
come trapped in the window. Unat-
tended children could become involved
in serious accidents.
The power windows operate when the
ignition switch is in the ON position or for
about 45 seconds after the ignition switch
is pushed to the OFF position. If the
driver ’ s or front passenger ’ s door is
opened during this period of about 45
seconds, power to the windows is can-
celed. SIC3279
Sedan
SIC3286A
Coupe 1. Driver side window
2. Front passenger side window
3. Rear left passenger side window
(Sedan only)
4. Rear right passenger side window
(Sedan only)
5. Window lock button
Main power window switch (driver ’ s
side) GUID-30535306-1466-4E47-9742-71642DD2CE80
To open or close the window, push down
* A
or pull up
* B
the switch and hold it.
The main switch (driver side switches) will
open or close all the windows.
Locking passengers ’ windows GUID-AF236370-F01C-4CB7-B27B-2400A5A7941F
When the lock button
* C
is pushed in, only
the driver side window can be opened or
closed. Push it in again to cancel.WINDOWS

Black plate (143,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3 Pre-driving checks and adjustments Keys ....................................................................... 3-2
Intelligent Key .................................................... 3-2
Valet hand-off ..................................................... 3-3
Doors ..................................................................... 3-4
Locking with mechanical key .............................. 3-4
Opening and closing windows with the
mechanical key ................................................... 3-5
Locking with inside lock knob ............................ 3-5
Locking with power door lock switch .................. 3-5
Automatic door locks .......................................... 3-6
Child safety rear door lock (Sedan) ..................... 3-6
Intelligent Key system ............................................ 3-7
Intelligent Key operating range .......................... 3-8
Door locks/unlocks precaution .......................... 3-9
Intelligent Key operation .................................. 3-10
Battery saver system ........................................ 3-12
Warning signals ................................................ 3-12
Troubleshooting guide ...................................... 3-13
Remote keyless entry system ................................ 3-14
How to use remote keyless entry system .......... 3-14
Hood .................................................................... 3-18
Trunk lid ............................................................... 3-18
Trunk lid release switch .................................... 3-19 Trunk open request switch .............................. 3-19
Trunk release power cancel switch .................. 3-20
Interior trunk lid release ................................. 3-21
Unique front and rear parts (INFINITI Performance
Line, Aerodynamic Package models) ..................... 3-21
Fuel-filler door ...................................................... 3-23
Opening the fuel-filler door ............................. 3-23
Fuel-filler cap .................................................. 3-23
Tilt/telescopic steering ......................................... 3-26
Manual operation (if so equipped) .................. 3-26
Electric operation (if so equipped) .................. 3-26
Sun visors ............................................................ 3-27
Mirrors ................................................................ 3-28
Inside mirror ................................................... 3-28
Outside mirrors ............................................... 3-29
Vanity mirror ................................................... 3-31
Automatic drive positioner (if so equipped) .......... 3-31
Entry/exit function (Automatic Transmission
Sedan models) ................................................ 3-31
Seat synchronization function ........................ 3-32
Memory storage .............................................. 3-33
System operation ............................................ 3-34

Black plate (146,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-4 Pre-driving checks and adjustmentsand “ Seats ” (P.1-2). GUID-CB09A4B1-D08E-43B9-9C2F-BFA68FF9F858
WARNING . Always have the doors locked while
driving. Along with the use of seat belts,
this provides greater safety in the event
of an accident by helping to prevent
persons from being thrown from the
vehicle. This also helps keep children
and others from unintentionally opening
the doors, and will help keep out
intruders.
. Before opening any door, always look for
and avoid oncoming traffic.
. Do not leave children unattended inside
the vehicle. They could unknowingly
activate switches or controls. Unat-
tended children could become involved
in serious accidents. SPA2527
LOCKING WITH MECHANICAL KEY GUID-FD0E2748-0AAA-4DDE-852C-19A9E0264D0B
The power door lock system allows you to
lock or unlock all doors simultaneously
using the mechanical key.
. Turning the driver ’ s door key cylinder to
the front of the vehicle
* 1
will lock all
doors.
. Turning the driver ’ s door key cylinder
once to the rear of the vehicle
* 2
will
unlock the driver ’ s door. After returning
the key to the neutral position
* 3
,
turning it to the rear again within 60
seconds will unlock all doors.DOORS

Black plate (148,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-6 Pre-driving checks and adjustmentsdoor, push the power door lock switch to
the unlock position
* 2
.
Lockout protection GUID-F17FC232-6651-4027-B680-5A82DB2977B3
When the power door lock switch (driver or
front passenger) is moved to the lock
position with the Intelligent Key in the port
and any door open, all doors will lock and
unlock automatically. With the Intelligent
Key left in the vehicle (not in the Intelligent
Key port) and any door open, all doors will
unlock automatically and a chime will
sound after the door is closed.
These functions help to prevent the In-
telligent Key from being accidentally
locked inside the vehicle.
AUTOMATIC DOOR LOCKS GUID-A10FB110-3B3F-40BA-97F3-3C215C27FFEF
. All doors lock automatically when the
vehicle speed reaches 15 MPH (24
km/h).
. All doors unlock automatically when the
ignition switch is placed in the OFF
position.
The automatic unlock function can be
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure: 1. Close all doors.
2. Place the ignition switch in the ON
position.
3. Within 20 seconds of performing Step
2, push and hold the power door lock
switch to the
position (UNLOCK) for
more than 5 seconds.
4. When activated, the hazard indicator
will flash twice. When deactivated, the
hazard indicator will flash once.
5. The ignition switch must be placed in
the OFF and ON position again between
each setting change.
When the automatic door unlock system is
deactivated, the doors do not unlock when
the ignition switch is placed in the OFF
position. To unlock the door manually, use
the inside lock knob or the power door lock
switch (driver ’ s or front passenger ’ s side). SPA2470
CHILD SAFETY REAR DOOR LOCK
(Sedan) GUID-DE27EA42-B974-4087-AC65-39A603A3ECDA
The child safety rear door lock helps
prevent doors from being opened acciden-
tally, especially when small children are in
the vehicle.
When the levers are in the lock position
* 1
, the rear doors can be opened only
from the outside.
To disengage, move the levers to the
unlock position
* 2
.

Black plate (160,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-18 Pre-driving checks and adjustments GUID-4B9DC6A0-E55B-4DB6-B6D3-74EFFFB751FB
SPA2318
1. Pull the hood lock release handle
* 1
located below the instrument panel;
the hood will then spring up slightly.
2. Pull the lever
* 2
up at the front of the
hood with your fingertips and raise the
hood.
3. When closing the hood, slowly close
the hood down to latch both the right
and left locks. Push the hood down to
lock the hood securely into place. WARNING . Make sure the hood is completely closed
and latched before driving. Failure to do
so could cause the hood to fly open and
result in an accident.
. If you see steam or smoke coming from
the engine compartment, to avoid injury
do not open the hood. GUID-8869D8E4-F743-48BC-A217-EB305909B923
WARNING . Do not drive with the trunk lid open. This
could allow dangerous exhaust gases to
be drawn into the vehicle. See “ Exhaust
gas (carbon monoxide) ” (P.5-3) of this
manual.
. Closely supervise children when they are
around cars to prevent them from play-
ing and becoming locked in the trunk
where they could be seriously injured.
Keep the car locked, with the trunk
closed, when not in use, and prevent
children ’ s access to Intelligent Keys.HOOD TRUNK LID

Black plate (163,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]INTERIOR TRUNK LID RELEASE GUID-4587ADD7-0824-4CA3-90BC-0B9E1446FA5C
WARNINGClosely supervise children when they are
around cars to prevent them from playing
and becoming locked in the trunk where
they could be seriously injured. Keep the car
locked, with the trunk lid securely latched,
when not in use, and prevent children ’ s
access to Intelligent Keys.
The interior trunk lid release mechanism
allows opening of the trunk lid in the event
that people become locked inside the trunk
or in the event of the loss of electrical
power such as a discharged battery.
Releasing inside the trunk GUID-4F494B4A-9594-4D01-BDD8-8ECF0B6F8122
To open the trunk lid from the inside, pull
the release handle
* 1
until the lock
releases and push up on the trunk lid.
The release lever is made of a material that
glows in the dark after a brief exposure to
ambient light.
The handle is located on the back of the
trunk lid as illustrated. Releasing from the rear seat GUID-0C5756BB-309D-4BDC-A10C-7CD141078C7C
Sedan: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
You can access the release handle through
the trunk pass-through (rear seat armrest).
(See “ Armrest ” (P.1-13).)
To open the trunk lid from the rear seat,
pull the release handle towards front of
vehicle until the lock releases.
Coupe: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
You can access the release handle by
folding the rear seat.
Pull the strap, located at the center bottom
of the seatback, and then fold down the
seatback. (See “ Rear seats ” (P.1-7).)
To open the trunk lid from the rear seat,
pull the release handle towards front of
vehicle until the lock releases. GUID-C9906368-3B16-4944-9B2F-9A9D4F648106
SPA2834
INFINITI Performance Line models
The INFINITI Performance Line models have
unique exhaust pipes. These parts are
close to the ground and may be damaged
if they contact objects such as parking
blocks, etc.
CAUTION Reduce vehicle speed to decrease the
possibility of damaging these parts when:
. driving on bumpy or rutted roads
. entering or exiting parking garages and
driveways
Pre-driving checks and adjustments
3-21UNIQUE FRONT AND REAR PARTS (INFINITI
Performance Line, Aerodynamic Package
models)