stop start INFINITI G37 2012 Owners Manual

Black plate (93,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]even when driving on a straight road. Drive
carefully to the nearest INFINITI retailer.
Intelligent Cruise Control (ICC)
system warning light (orange; if so
equipped) GUID-FF29B1E7-F6C4-403D-8621-C6A7F86246EF
This light comes on if there is a malfunc-
tion in the Intelligent Cruise Control (ICC)
system.
If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the
vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.
Intelligent Key warning light GUID-7E046839-8973-408F-BF89-AB2223E4A062
After the ignition switch is pushed to the
ON position, this light comes on for about
2 seconds and then turns off.
This light warns of a malfunction with the
Intelligent Key system.
If the light comes on while the engine is
stopped, it may be impossible to start the
engine. If the light comes on while the engine is running, you can drive the
vehicle. However in these cases, contact
an INFINITI retailer for repair as soon as
possible.
Low tire pressure warning
light GUID-4B828BB9-9D9C-4BA9-B41A-9EF6D3CB156D
Your vehicle is equipped with a Tire
Pressure Monitoring System (TPMS) that
monitors the tire pressure of all tires
except the spare.
The low tire pressure warning light warns
of low tire pressure or indicates that the
TPMS is not functioning properly.
After the ignition switch is pushed ON, this
light illuminates for about 1 second and
turns off.
Low tire pressure warning: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
If the vehicle is being driven with low tire
pressure, the warning light will illuminate.
A CHECK TIRE PRESSURE warning also
appears on the dot matrix liquid crystal
display.
When the low tire pressure warning light
illuminates, you should stop and adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. The low tire pressure warning light does not automati-
cally turn off when the tire pressure is
adjusted. After the tire is inflated to the
recommended pressure, the vehicle must
be driven at speeds above 16 MPH (25
km/h) to activate the TPMS and turn off the
low tire pressure warning light. Use a tire
pressure gauge to check the tire pressure.
The CHECK TIRE PRESSURE warning is
active as long as the low tire pressure
warning light remains illuminated.
For additional information, see “ Dot matrix
liquid crystal display ” (P.2-20), “ Tire Pres-
sure Monitoring System (TPMS) ” (P.5-4)
and “ Tire Pressure Monitoring System
(TPMS) ” (P.6-2).
TPMS malfunction: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
If the TPMS is not functioning properly, the
low tire pressure warning light will flash for
approximately 1 minute when the ignition
switch is pushed ON. The light will remain
on after the 1 minute. Have the system
checked by an INFINITI retailer. The CHECK
TIRE PRESSURE warning does not appear if
the low tire pressure warning light illumi-
nates to indicate a TPMS malfunction.
For additional information, see “ Tire Pres-
sure Monitoring System (TPMS) ” (P.5-4).
Instruments and controls
2-15

Black plate (94,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-16 Instruments and controlsWARNING. If the light does not illuminate with the
ignition switch pushed ON, have the
vehicle checked by an INFINITI retailer as
soon as possible.
. If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle speed,
pull off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and in-
crease the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and could
result in serious personal injury. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the Tire
and Loading Information label to turn
the low tire pressure warning light OFF. If
the light still illuminates while driving
after adjusting the tire pressure, a tire
may be flat. If you have a flat tire,
replace it with a spare tire as soon as
possible. . When a spare tire is mounted or a wheel
is replaced, the TPMS will not function
and the low tire pressure warning light
will flash for approximately 1 minute.
The light will remain on after the 1
minute. Contact your INFINITI retailer as
soon as possible for tire replacement
and/or system resetting.
. Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
CAUTION . The TPMS is not a substitute for the
regular tire pressure check. Be sure to
check the tire pressure regularly.
. If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS
may not operate correctly.
. Be sure to install the specified size of
tires to the four wheels correctly.
Master warning light GUID-BFD238A1-B056-42EA-B9A0-FCCF2B17501F
When the ignition switch is in the ON
position, the master warning light illumi- nates if any of the following are displayed
on the dot matrix liquid crystal display:
. No key warning
. Low fuel warning
. Low washer fluid warning
. Parking brake release warning
. Door/trunk open warning
. Loose fuel cap warning
. Check tire pressure warning
See “ Dot matrix liquid crystal display ” (P.2-
20).
Preview Function warning light
(orange; if so equipped) GUID-B4E486C7-1748-4EBD-A37A-79C9F389E7E0
The light comes on if there is a malfunction
in the Brake Assist (with Preview Function)
system.
If the warning light comes on, park the
vehicle in a safe place. Turn the engine off,
restart the engine, resume driving and set
the ICC system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the
vehicle is still driveable under normal
conditions, have the vehicle checked at
an INFINITI retailer.

Black plate (100,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]2-22 Instruments and controlsINDICATORS FOR OPERATION GUID-3F80C245-4DDE-4CCD-9BA2-FE533BE15F57
1. Engine start operation indicator
(Automatic Transmission models) GUID-865F0D42-3E6C-4071-B120-AFF1A5EE4D2E
This indicator appears when the selector
lever is in the P (Park) position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed.
2. Intelligent Key insertion indicator GUID-581E65CB-42A3-471E-923A-B9CDD6DBCCC9
This indicator appears when the Intelligent
Key needs to be inserted into the Intelli-
gent Key port. (For example, the Intelligent
Key battery is discharged.)
If this indicator appears, insert the Intelli-
gent Key into the Intelligent Key port in the
correct direction. (See “ Push-button igni-
tion switch ” (P.5-9).)
3. Intelligent Key removal indicator GUID-0F76AEA4-8CB1-4BBC-A994-137701CB6218
This indicator appears when the driver ’ s
door is opened with the ignition switch in
the OFF or LOCK position and the Intelli-
gent Key placed in the Intelligent Key port.
A key reminder chime also sounds.
If this indicator appears, remove the
Intelligent Key from the Intelligent Key port
and take it with you when leaving the vehicle.
4. NO KEY warning GUID-B266EC58-8CB6-45C9-B5B7-7FF3A17CB567
This warning appears in either of the
following conditions.
No key inside the vehicle: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the door is
closed with the Intelligent Key left outside
the vehicle and the ignition switch in the
ACC or ON position. Make sure that the
Intelligent Key is inside the vehicle.
Unregistered Intelligent Key: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the ignition
switch is pushed from the LOCK position
and the Intelligent Key cannot be recog-
nized by the system. You cannot start the
engine with an unregistered key. Use the
registered Intelligent Key.
See “ Intelligent Key system ” (P.3-7) for
more details.
5. SHIFT “ P ” warning (Automatic
Transmission models) GUID-9BDEFCBE-BD2F-42CF-B3EF-1A2E660B253C
This warning appears when the ignition
switch is pushed to stop the engine with
the selector lever in any position except
the P (Park) position.
If this warning appears, move the selector lever to the P (Park) position or push the
ignition switch to the ON position.
An inside warning chime will also sound.
(See “ Intelligent Key system ” (P.3-7).)
6. “ PUSH ” warning (Automatic
Transmission models) GUID-C4F385F1-244F-4AA8-A2FB-F05B8CE33F2B
This warning appears when the selector
lever is moved to the P (Park) position with
the ignition switch in the ACC position after
the SHIFT “ P ” warning appears.
To push the ignition switch to the OFF
position, perform the following procedure:
SHIFT “ P ” warning ? (Move the selector
lever to “ P ” ) ? PUSH warning ? (Push the
ignition switch ? ignition switch position
is turned to ON) ? PUSH warning ? (Push
the ignition switch ? ignition switch
position is turned to OFF)
7. Intelligent Key battery discharge
indicator GUID-27367EF5-F931-4EBC-8576-1379DE51DE47
This indicator appears when the Intelligent
Key battery is running out of power.
If this indicator appears, replace the
battery with a new one. (See “ Intelligent
Key battery replacement ” (P.8-26).)

Black plate (101,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]8. Engine start operation indicator
(Manual Transmission models) GUID-6F348F29-B160-4632-B05C-A45F6D5E7AD7
This indicator means that the engine will
start by pushing the ignition switch with
the clutch pedal depressed.
9. Parking brake release warning GUID-7289EFE7-F400-4C19-9597-F8AA159911CA
This warning appears when the vehicle
speed is above 4 MPH (7 km/h) and the
parking brake is applied.
10. Low fuel warning GUID-2FE47C40-46BC-4EC8-AC52-E90EBB5F8B0F
This warning appears when the fuel level in
the tank is getting low. Refuel as soon as it
is convenient, preferably before the fuel
gauge reaches the empty (E) position.
There is a small reserve of fuel remaining
in the tank when the fuel gauge reaches
the empty (E) position.
11. Low washer fluid warning GUID-54C94524-E0BC-4326-8A11-B2CD705757A6
This warning appears when the washer
tank fluid is at a low level. Add washer fluid
as necessary. (See “ Window washer fluid ”
(P.8-16).)
12. Door/trunk open warning (igni-
tion switch is in the ON position) GUID-50585695-BAF8-48B7-8A81-CEA312693DE1
This warning appears if any of the doors and/or the trunk lid are open or not closed
securely. The vehicle icon indicates which
door or the trunk lid is open on the display.
13. Loose fuel cap warning GUID-479E9C15-B26C-477B-8AA7-ED29D6CD76ED
This warning appears when the fuel-filler
cap is not tightened correctly after the
vehicle has been refueled. (See “ Fuel-filler
door ” (P.3-23).)
14. Check tire pressure warning GUID-174D3E5C-C80F-432A-944F-EE13C51D1486
This warning appears when the low tire
pressure warning light in the meter illumi-
nates to indicate the low tire pressure. If
this warning appears, stop the vehicle and
adjust the tire pressure to the recom-
mended COLD tire pressure shown on the
Tire and Loading Information label. (See
“ Low tire pressure warning light ” (P.2-15)
and “ Tire Pressure Monitoring System
(TPMS) ” (P.5-4).)
15. “ Time to rest ” indicator GUID-9639DC97-247E-4499-BA1B-AFF133E94400
This indicator appears when the set “ time
to rest ” indicator activates. You can set the
time for up to 6 hours. (See “ Trip
computer ” (P.2-26).) 16. Low outside temperature warn-
ing GUID-E9986E7D-DDA6-4BCF-8D8E-D8F9C645C41B
This warning appears if the outside tem-
perature is below 37 8 F (3 8 C). The warning
can be set not to be displayed. (See “ Trip
computer ” (P.2-26).)
17. Cruise indicator GUID-8437A118-88BE-4895-A266-56D415AE4EC7
Cruise main switch indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The indicator is displayed when the cruise
control main switch is pushed. When the
main switch is pushed again, the indicator
disappears. When the cruise control main
switch indicator is displayed, the cruise
control system is operational.
Cruise set switch indicator: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The indicator is displayed while the vehicle
speed is controlled by the cruise control
system. If the indicator blinks while the
engine is running, it may indicate that the
cruise control system is not functioning
properly. Have the system checked by an
INFINITI retailer.
See “ Cruise control ” (P.5-21) for details.
Instruments and controls
2-23

Black plate (113,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]It is generally desirable not to turn off
the headlights for short intervals (for
example, when the vehicle stops at a
traffic signal). Even when the daytime
running lights are active (Canada only),
the xenon headlights do not turn on.
This way the life of the xenon head-
lights is not reduced.
. If the xenon headlight bulb is close to
burning out, the brightness will dras-
tically decrease, the light will start
blinking, or the color of the light will
become reddish. If one or more of the
above signs appear, contact an INFINITI
retailer. SIC3267
HEADLIGHT SWITCH GUID-33AE3B12-CA6A-4F4B-937B-B94D10FCE3CF
Lighting GUID-7A3ED0E6-B819-4CBD-BBCC-8D6AAA3D091F
* 1
Turn the switch to the position:
The front parking, side marker, tail,
license plate and instrument lights
will come on.
* 2
Turn the switch to the position:
Headlights will come on and all the
other lights remain on. SIC3268
Autolight system (if so equipped) GUID-B0C5ED39-4191-407B-8F10-92C5231D8B53
The autolight system allows the headlights
to be set so they turn on and off
automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
AUTO position
* 1
.
2. Push the ignition switch to the ON
position.
3. The autolight system automatically
turns the headlights on and off.
To turn the autolight system off, turn the
switch to the OFF,
or position.
Instruments and controls
2-35

Black plate (165,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]GUID-02CF0A75-C84C-42E5-8EC5-1F52978DFE6D
SPA2554
Sedan
SPA1562A
Coupe OPENING THE FUEL-FILLER DOOR GUID-992E40DE-AC25-44A9-842E-2A963AAA7D5B
To open the fuel-filler door, unlock the fuel-
filler door by using one of the following
operations, then push the right side of the
door (Sedan) or push the left side of the
door (Coupe).
. Push the door handle request switch
with the Intelligent Key carried with
you.
. Push the UNLOCK button on the Intelli-
gent Key.
. Insert the mechanical key into the door
lock cylinder and turn it to the rear of
the vehicle.
. Push the power door lock switch to the
UNLOCK position.
To lock, close the fuel-filler door securely
and lock all doors by operating the door
handle request switch, the LOCK button on
the Intelligent Key, the mechanical key or
the power door lock switch. FUEL-FILLER CAP GUID-FACDECE2-8451-40C3-841E-0B67C4802921
WARNING . Gasoline is extremely flammable and
highly explosive under certain condi-
tions. You could be burned or seriously
injured if it is misused or mishandled.
Always stop engine and do not smoke or
allow open flames or sparks near the
vehicle when refueling.
. Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off
automatically. Continued refueling may
cause fuel overflow, resulting in fuel
spray and possibly a fire.
. Use only an original equipment type
fuel-filler cap as a replacement. It has a
built-in safety valve needed for proper
operation of the fuel system and emis-
sion control system. An incorrect cap can
result in a serious malfunction and
possible injury. It could also cause the
malfunction indicator light (MIL) to
come on.
. Never pour fuel into the throttle body to
attempt to start your vehicle.
Pre-driving checks and adjustments
3-23FUEL-FILLER DOOR

Black plate (176,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]3-34 Pre-driving checks and adjustmentsapproximately 0.5 second. When the
memory has stored in position, the
indicator light will stay on for approxi-
mately 5 seconds.
. If the battery cable is disconnected, or if
the fuse opens, the memory will be
canceled. In this case, reset the desired
position using the previous procedure.
. If optional Intelligent Keys are added to
your vehicle, the memory storage pro-
cedure to switch 1 or 2 and linking
Intelligent Key procedure to a stored
memory position should be performed
again for each Intelligent Key. For
additional Intelligent Key information,
see “ Keys ” (P.3-2).
Selecting the memorized position GUID-739A81F0-8862-49C2-BBA8-117F41F648F9
1. Automatic transmission models:
Move the selector lever to the P (Park)
position.
Manual transmission models:
Apply the parking brake.
2. Raise the seatback (Coupe).
3. Use one of the following methods to
move the driver ’ s seat, the outside
mirrors and the steering wheel. .
Push the ignition switch to the ON
position and push the memory
switch (1 or 2) fully for at least 1
second. .
Within 45 seconds of opening the
driver ’ s door, push the memory
switch (1 or 2) fully for at least 1
second.
The driver ’ s seat, steering column
and outside mirrors will move to the
memorized position with the indica-
tor light flashing, and then the light
will stay on for approximately 5
seconds.
For manual transmission models, the
memory positions can be selected even
when the engine is running. In this case,
move the shift lever to the N (Neutral)
position and apply the parking brake.
Then, perform step 2.
SYSTEM OPERATION GUID-0383C8BF-12F8-48D0-9B28-5A2A0DCC8D55
The automatic drive positioner system will
not work or will stop operating under the
following conditions:
. When the vehicle speed is above 4 MPH
(7 km/h).
. When the adjusting switch for the
driver ’ s seat and steering column is
turned on while the automatic drive positioner is operating.
. When the memory switch 1 or 2 is not
pushed for at least 1 second.
. When the seat, steering column and
outside mirrors have already been
moved to the memorized position.
. When no position is stored in the
memory switch.
. When the parking brake is released (MT
models).
. When the speed is above 4 MPH (7
km/h) while the parking brake is
applied (MT models).
To restart the drive positioner system,
move the parking brake to off and on.
. When the engine is started while
moving the automatic drive positioner.
. When the AT selector lever is moved
from the P (Park) position to any other
position. (However, it will not be
canceled if the switch is pushed while
the seat and steering column are
returning to the previous positions
(entry/exit function).)
. When the driver ’ s door remains open
for more than 45 seconds and the
ignition switch is not in the ON posi-
tion.

Black plate (200,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-22 Monitor, climate, audio, phone and voice recognition systems SAA2491
Image Viewer (models with naviga-
tion system) GUID-3A8CCE29-BAF6-4276-8E18-96A1950EFDF7
The image files in the USB memory will be
displayed. To display the Image Viewer,
push the SETTING button, select the
“ Other ” key and then select the “ Image
Viewer ” key. The image of the selected file
is displayed on the right side of the screen.
When a number of folders are included in
the USB memory, select a folder from the
list to display the file list.
Images will not be shown on the display
while the vehicle is in any drive position to
reduce driver distraction. To view images, stop the vehicle in a safe location and
apply the parking brake.
SAA2492
Full Screen Display: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The full screen display will appear when
selecting the “ Full Screen Display ” key.
To operate the Image Viewer or to change
the settings, select the desired key using
the INFINITI controller.
.
(Start)
Select the “ ” key to start playing
the slideshow.
.
(Stop)
Select the “
” key to stop the
slideshow.
.
(Next)
Select the “ ” key to display the next

Black plate (240,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]4-62 Monitor, climate, audio, phone and voice recognition systemsREPEAT (RPT), RANDOM (RDM) (Type
A): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the RPT button is pushed while the
CD is played, the play pattern can be
changed as follows:
(CD) NOS2606
(CD with compressed audio files) NOS2607
REPEAT (RPT) (Type B): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the SCAN·RPT button is pushed while
the CD is played, the play pattern can be
changed as follows:
(CD) NOS2079
(CD with MP3 or WMA)
NOS2080CD EJECT: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the CD EJECT button is pushed with
the CD loaded, the CD will be ejected.
When this button is pushed while the CD is
being played, the CD will be ejected.
If the CD comes out and is not removed, it
will be pulled back into the slot to protect
it.
DVD (Digital Versatile Disc) PLAYER
OPERATION (models with naviga-
tion system) GUID-8205EDF5-3DB4-4E4E-8CDD-3F75914B7BB8
Precautions GUID-8812ACDC-FD40-4CAA-9CB9-437BDD03B225
Start the engine when using the DVD
entertainment system.
Movies will not be shown on the front
display while the vehicle is in any drive
position to reduce driver distraction. Audio
is available when a movie is played. To
view movies in the front display, stop the
vehicle in a safe location, move the
selector lever to the P (Park) position
(Automatic Transmission models) or apply
the parking brake (Manual Transmission
models). WARNING . The driver must not attempt to operate
the DVD system or wear the headphones
while the vehicle is in motion so that full
attention may be given to vehicle opera-
tion.
. Do not attempt to modify the system to
display a movie on the front screen while
the vehicle is being driven. Doing so may
distract the driver and may cause a
collision and serious personal injury or
death.
CAUTION . Only operate the DVD while the vehicle
engine is running. Operating the DVD for
extended periods of time with the
engine OFF can discharge the vehicle
battery.
. Do not allow the system to get wet.
Excessive moisture such as spilled
liquids may cause the system to mal-
function.
. While playing VIDEO-CD media, this DVD

Black plate (241,1)
[ Edit: 2012/ 1/ 17 Model: V36-D ]player does not guarantee complete
functionality of all VIDEO-CD formats.
Display settings GUID-720BCAE9-AA46-4971-99AF-5389717886E1
To adjust the front display mode, push the
SETTING button while the DVD is being
played, select the “ Others ” key and then
select the “ Display ” key.
To adjust the display ON/OFF, brightness,
tint, color and contrast, select the “ Display
Adjustment ” key and then select each key.
Then you can adjust each item using the
INFINITI controller. After changes have
been made push the BACK button to save
the setting. SAA2497
Playing a DVD GUID-EEE03BD8-3059-4917-ACAC-2BF65D28CBB9
DISC·AUX button: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Park the vehicle in a safe location for the
front seat occupants to operate the DVD
drive while watching the images.
Push the DISC·AUX button on the instru-
ment panel and turn the display to the DVD
mode.
When a DVD is loaded, it will be replayed
automatically.
The operation screen will be turned on
when the DISC·AUX button located on the
instrument panel is pushed while a DVD is
being played, and it will turn off auto- matically after a period of time. To turn it
on again, push the DISC·AUX button again.
DVD operation keys: GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the DVD is playing without the
operation screen being shown, you may
use the touch screen to select items from
the displayed video. You may also use the
INFINITI controller to select an item from
the displayed video. When the operation
screen is being shown, use the INFINITI
controller or touch screen to select an item
from the displayed menus.
PAUSE:
Select the “
” key to pause the DVD. To
resume playing the DVD, use the “ PLAY ”
key.
PLAY:
Select the “
” key to start playing the
DVD, for example, after pausing the DVD.
STOP:
Select the “
” key to stop playing the
DVD.
Monitor, climate, audio, phone and voice recognition systems
4-63