driver seat adjustment INFINITI M 2011 Owners Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: M, Model: INFINITI M 2011Pages: 488, PDF Size: 4.26 MB
Page 37 of 488
Center of rear seat
Selecting correct set of seat belts :
The center seat belt buckle is identified by the
CENTER mark
A. The center seat belt tongue
can be fastened onlyinto the center seat belt
buckle.
Shoulder belt height adjustment
(front seats)
The shoulder belt anchor height should be
adjusted to the position best for you. (See
“PRECAUTIONS ON SEAT BELT USAGE” earlier in
this section.)
To adjust, push the button
A, and then move
the shoulder belt anchor to the desired posi-
tion, so that the belt passes over the center of
the shoulder. The belt should be away from
your face and neck, but not falling off of your
shoulder. Release the adjustment button to lock
the shoulder belt anchor into position.
WARNING
● After adjustment, release the adjustment
button and try to move the shoulder belt
anchor up and down to make sure it is se-
curely fixed in position.
● The shoulder belt anchor height should be
adjusted to the position best for you. Failure
to do so may reduce the effectiveness of the
entire restraint system and increase the
chance or severity of injury in an accident.
SEAT BELT EXTENDERS
If, because of body size or driving position, it is
not possible to properly fit the lap-shoulder belt
and fasten it, an extender that is compatible
with the installed seat belts is available that
can be purchased. The extender adds approxi-
mately 8 in (200 mm) of length and may be
used for either the driver or front passenger
seating position. See an INFINITI retailer for
assistance with purchasing an extender if an
extender is required.
SSS1084SSS0294A
1-16Safety — Seats, seat belts and supplemental restraint system
—
—
01/11/10—pattie
Page 135 of 488
WARNING
●Always have the doors locked while driving.
Along with the use of seat belts, this pro-
vides greater safety in the event of an acci-
dent by helping to prevent persons from be-
ing thrown from the vehicle. This also helps
keep children and others from unintention-
ally opening the doors, and will help keep
out intruders.
● Before opening any door, always look for and
avoid oncoming traffic.
● Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls. Unattended children
could become involved in serious accidents.
LOCKING WITH MECHANICAL KEY
The power door lock system allows you to lock
or unlock all doors simultaneously using the
mechanical key.
● Turning the driver’s door key cylinder to the
front of the vehicle
1will lock all doors.
● Turning the driver’s door key cylinder once
to the rear of the vehicle
2will unlock the
driver’s door. After returning the key to the
neutral position
3, turning it to the rear
again within 60 seconds will unlock all
doors. ●
You can switch the lock system to the mode
that allows you to open all the doors when
the key is turned once. (See “HOW TO USE
SETTING BUTTON” in the “4. Monitor, cli-
mate, audio, phone and voice recognition
systems” section.)
OPENING AND CLOSING WINDOWS
WITH THE MECHANICAL KEY
The driver’s door key operation also allows you
to open and close the window that is equipped
with the automatic open/close function. (See
“POWER WINDOWS” in the “2. Instruments and
controls” section).
To open the window, turn the driver’s door key
cylinder to the rear of the vehicle for longer than
1 second . The door is unlocked and the window
keeps opening while turning the key.
This function can also be performed by pushing
and holding the door UNLOCK button of the
Intelligent Key. (See “REMOTE KEYLESS ENTRY
SYSTEM” later in this section.)
To close the window, turn the driver’s door key
cylinder to the front of the vehicle for longer
than 1 second . The door is locked and the
window keeps closing while turning the key.
SPA2527
DOORS
3-4Pre-driving checks and adjustments
—
—
01/13/10—tbrooks
Page 152 of 488
To remove the fuel-filler cap:
1. Turn the fuel-filler cap counterclockwise toremove.
2. Put the fuel-filler cap on the cap holder
A
while refueling.
To install the fuel-filler cap:
1. Insert the fuel-filler cap straight into the fuel-filler tube.
2. Turn the fuel-filler cap clockwise until it clicks. The fuel-filler cap is a ratcheting
type.
LOOSE FUEL CAP warning (if so
equipped)
The LOOSE FUEL CAP warning appears on the
dot matrix liquid crystal display when the fuel-
filler cap is not tightened correctly after the
vehicle has been refueled.
To turn off the warning, perform the following:
1. Remove and install the fuel-filler cap assoon as possible. (See “FUEL-FILLER
CAP”.)
2. Tighten the fuel-filler cap until it clicks.
3. Push the • switch
Aon the right side of
the combination meter panel for longer
than 1 second to turn off the LOOSE FUEL
CAP warning after tightening the fuel cap.
WARNING
● Do not adjust the steering wheel while driv-
ing. You could lose control of your vehicle
and cause an accident.
● Do not adjust the steering wheel any closer
to you than is necessary for proper steering
operation and comfort. The driver’s air bag
inflates with great force. If you are unre-
strained, leaning forward, sitting sideways
or out of position in any way, you are at
greater risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it when
it inflates. Always sit back against the seat-
back and as far away as practical from the
steering wheel. Always use the seat belts.
SPA2736SPA2832
TILT/TELESCOPIC STEERING
Pre-driving checks and adjustments3-21
—
—
07/15/10—tbrooks
Page 153 of 488
ELECTRIC OPERATION
Tilt or telescopic operation
Move the lever to adjust the steering wheel up
or down, forward or rearward to the desired
position.
Entry/Exit function operation :
The automatic drive positioner system will
make the steering wheel move up automatically
when the driver’s door is opened with the
ignition switch in the LOCK position. This lets
the driver get into and out of the seat more
easily.
For more information, see “AUTOMATIC DRIVE
POSITIONER” later in this section.
1. To block glare from the front, swing downthe main sun visor
1.
2. To block glare from the side, remove the main sun visor from the center mount and
swing the visor to the side
2.
3. Slide the sun visor
3in or out as needed.
SPA2737
SPA2471
SUN VISORS
3-22Pre-driving checks and adjustments
—
—
07/14/10—dstomski
Page 157 of 488
VANITY MIRROR
To use the front vanity mirror, pull down the sun
visor and pull up the cover.The automatic drive positioner system has four
features:
●
Entry/exit function
● Seat synchronization function
● Memory storage
● Setting memory function
ENTRY/EXIT FUNCTION
This system is designed so that the driver’s seat
and steering column will automatically move
when the selector lever is in the P (Park)
position. This allows the driver to get into and
out of the driver’s seat more easily.
The driver’s seat will slide backward and the
steering wheel will move up when the driver’s
door is opened with the ignition switch in the
LOCK position.
The driver’s seat and steering wheel will return
to the previous positions when the ignition
switch is pushed to the ACC position.
The driver’s seat will not return to the previous
positions if the seat or steering adjusting
switch is operated when the seat is at the exit
position.
Cancel or activate entry/exit function
The selector lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink
twice when the function is activated. Note that
the indicator lights may illuminate after 5 sec-
onds while holding the SET switch. This indi-
cates readiness for linking the Intelligent Key to
a stored memory position. Keep the SET switch
pressed for more than 10 seconds to turn on or
off the entry/exit function.
The entry/exit function can also be activated or
canceled if the “Lift Steering Wheel on Exit” key
or “Slide Driver Seat Back on Exit” key is turned
to ON or OFF in the “Comfort & Conv.” settings.
(See “VEHICLE INFORMATION AND SETTINGS” in
the “4. Monitor, climate, audio, phone and
voice recognition systems” section.)
AUTOMATIC DRIVE POSITIONER
3-26Pre-driving checks and adjustments
—
—
07/14/10—dstomski
Page 158 of 488
Initialize entry/exit function
If the battery cable is disconnected, or if the
fuse opens, the entry/exit function will not work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is turned from the ON position to the
LOCK position. The entry/exit function will be
activated.
SEAT SYNCHRONIZATION FUNCTION
The seat synchronization function automatically
adjusts the positions of the steering wheel and
outside mirrors when the seat is adjusted using
the power seat switches.
However, the steering wheel and outside mir-
rors will not move if the seat is adjusted over
the maximum thresholds. The system considers
that the steering wheel and outside mirror
adjustments are not necessary because the
seat may not be adjusted for the driving posi-
tion. Note that the function is set to disabled as
the factory default setting.
The seat synchronization function operates un-
der the following conditions:●
The ignition switch is in the ON position.
● The selector lever is in the P (Park) position.
If the outside mirrors or the steering wheel
reaches its maximum adjustment, the function
is automatically disabled. Restart the function
by selecting a previously stored seat memory
position using the memory switches (1 or 2). An
Intelligent Key that was previously linked to the
stored seat memory can also be used to restart
the function.
If a seat position was not previously stored in
the seat memory, restart the function by adjust-
ing the steering wheel and outside mirrors
manually for your best driving position and then
drive the vehicle above 4 MPH (7 km/h).
Cancel or activate seat
synchronization function
The selector lever must be in the P (Park)
position with the ignition switch in the ACC
position.
MEMORY STORAGE
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow
these procedures to use the memory system.
1. Move the selector lever to the P (Park) position.
SPA2792
Pre-driving checks and adjustments3-27
—
—
07/14/10—dstomski
Page 159 of 488
2. Push the ignition switch to the ON posi-tion.
3. Adjust the driver’s seat, steering column and outside mirrors to the desired posi-
tions by manually operating each adjust-
ing switch. For additional information, see
“SEATS” in the “1. Safety — Seats, seat
belts and supplemental restraint system”
section and “TILT/TELESCOPIC STEERING”
page 3-21 and “OUTSIDE MIRRORS” ear-
lier in this section.
4. Push the SET switch and, within 5 sec- onds, push the memory switch (1 or 2)
fully for at least 1 second.
The indicator light for the pushed memory
switch will stay on for approximately 5 sec-
onds after pushing the switch.
If memory is stored in the same memory
switch, the previous memory will be deleted.
Linking Intelligent Key to a stored
memory position
The Intelligent Key can be linked to a stored
memory position with the following procedure.
1. Follow the steps for storing a memoryposition. 2. While the indicator light for the memory
switch being set is illuminated for 5 sec-
onds, push the
button on the Intel-
ligent Key. If the indicator light blinks, the
Intelligent Key is linked to that memory
setting.
Push the ignition switch to the OFF position,
and then push the
button on the Intelli-
gent Key. The driver’s seat, steering wheel and
outside mirrors will move to the memorized
position.
Confirming memory storage
● Push the ignition switch to the ON position
and push the SET switch. If the main memory
has not been stored, the indicator light will
come on for approximately 0.5 second.
When the memory has stored in position, the
indicator light will stay on for approximately
5 seconds.
● If the battery cable is disconnected, or if the
fuse opens, the memory will be canceled. In
this case, reset the desired position using
the previous procedure.
● If optional Intelligent Keys are added to your
vehicle, the memory storage procedure to
switch 1 or 2 and linking Intelligent Key
procedure to a stored memory position
should be performed again for each Intelli- gent Key. For additional Intelligent Key infor-
mation, see “KEYS” earlier in this section.
Selecting the memorized position
1. Move the selector lever to the P (Park)
position.
2. Use one of the following methods to move the driver’s seat, the outside mirrors and
the steering wheel.
●Push the ignition switch to the ON posi-
tion and push the memory switch (1 or 2)
fully for at least 1 second.
● Within 45 seconds of opening the driver’s
door, push the memory switch (1 or 2)
fully for at least 1 second.
The driver’s seat, steering column and out-
side mirrors will move to the memorized
position with the indicator light flashing,
and then the light will stay on for approxi-
mately 5 seconds.
SETTING MEMORY FUNCTION
The status of the following settings can be
linked to the Intelligent Key and the memorized
settings can be available for each Intelligent
Key.
● Climate control system
● Navigation system (if so equipped)
3-28Pre-driving checks and adjustments
—
—
07/14/10—dstomski
Page 160 of 488
●Audio system
To use the memory function, lock the doors with
the Intelligent Key that is linked to the settings.
To enable the memorized settings:
1. Carry the Intelligent Key that is linked to the settings, and unlock the doors by
pushing the driver’s door handle request
switch or UNLOCK
button on the
Intelligent Key.
2. Push the ignition switch to the “ON” position. “Connection with the key has
been done” will be displayed on the
screen and the memorized settings are
available (only when a new Intelligent Key
is used).
SYSTEM OPERATION
The automatic drive positioner system will not
work or will stop operating under the following
conditions:
●When the vehicle speed is above 4 MPH
(7 km/h).
● When the adjusting switch for the driver’s
seat and steering column is turned on while
the automatic drive positioner is operating.
● When the memory switch 1 or 2 is not
pushed for at least 1 second. ●
When the seat, steering column and outside
mirrors have already been moved to the
memorized position.
● When no position is stored in the memory
switch.
● When the engine is started while moving the
automatic drive positioner.
● When the selector lever is moved from the P
(Park) position to any other position. (How-
ever, it will not be canceled if the switch is
pushed while the seat and steering column
are returning to the previous positions
(entry/exit function).)
● When the driver’s door remains open for
more than 45 seconds and the ignition
switch is not in the ON position.
● The seat synchronization function is auto-
matically disabled if the outside mirrors or
steering wheel reaches its maximum adjust-
ment.
● The seat synchronization function will not
operate if the seat is adjusted over one of
the following maximum thresholds:
– Seat sliding: 3.0 in (76 mm)
– Seatback reclining: 9.1 degrees
– Seat lifter (rear side): 0.8 in (20 mm)
Pre-driving checks and adjustments3-29
—
—
07/14/10—dstomski
Page 485 of 488
Seat belt(s)Child safety ................ .1-17
Infants .................... 1-18
Injured persons ............... 1-13
Larger children ............... 1-18
Precautions on seat belt usage ......1-11
Pre-crash seat belts with comfort
function ................... 1-13
Pregnant women .............. 1-13
Seat belt cleaning .............7-6
Seat belt extenders ............1-16
Seat belt maintenance ...........1-17
Seat belts .................. 1-11
Seat belts with pretensioners ......1-47
Seat belt warning light and chime ....2-14
Shoulder belt height adjustment .....1-16
Small children ............... 1-18
Three-point type .............. 1-14
Seat(s) Climate controlled seats .........2-40
Driver-side memory ............3-26
Heated seats ................ 2-39
Seats .....................1-2
Seat synchronization function ........3-27
Security system (INFINITI Vehicle Immobilizer
System), Engine start .............2-29
Security system, Vehicle security system . .2-27
Selector lever Shift lock release ............. .5-15
Servicing air conditioner
(See automatic climate control) .......4-30
Servicing climate control ...........4-44
SETTING button ................ .4-14
Shifting, Automatic transmission .......5-12
Shift lock release Transmission ............... .5-15Shoulder belt height adjustment
.......1-16
Spare tire .................... .9-9
Spark plugs .................. .8-19
Speedometer .................. .2-6
Starting Before starting the engine .........5-10
Precautions
when starting and driving . . 5-2
Starting the engine ............. 5-11
STATUS button ................. .4-8
Status light, Front passenger air bag . . . .1-43
Steering Heated steering wheel ...........2-38
Power steering fluid ............8-14
Power steering system ..........5-84
Steering lock release malfunction
indicator .................. 2-21
Steering-wheel-mounted controls for
audio .................... 4-83
Tilt/telescopic steering ..........3-21
Storage .................... .2-45
Sunglasses holder .............. .2-46
Sunshade (rear) ............... .2-53
Sun visors ................... .3-22
Supplemental air bag warning labels . . . .1-48
Supplemental air bag warning light . .1-48 , 2-15
Supplemental restraint system ........1-36
Supplemental restraint system, Precautions
on supplemental restraint system ......1-36
Switch Autolight switch ............. .2-33
Fog light switch .............. 2-37
Hazard warning flasher switch ......2-37
Headlight switch .............. 2-33
Ignition switch automatic transmission
models ................... 5-12
Intelligent Brake Assist (IBA) OFF switch . . 2-42
Power door lock switch...........3-5
Rear window and outside mirror defroster
switch .................... 2-32
Turn signal switch ............. 2-37
Vehicle dynamic control (VDC) off
switch ................... 2-43
T
Tachometer ................... .2-7
Temperature gauge, Engine coolant
temperature gauge .............. .2-7
Theft (INFINITI Vehicle Immobilizer System),
Engine start .................. .2-29
Three-way catalyst ............... .5-2
Tilt/telescopic steering .............3-21
Tire Tire replacement indicator ........2-23
Tire rotation ................ 8-37
Tire pressure, Low tire pressure warning
light ...................... .2-13
Tires Flat tire ................... .6-2
Low tire pressure warning system ....5-3
Spare tire ................. 8-40
Tire and Loading information label . . . 8-32
Tire chains ................. 8-37
Tire dressing ................7-4
Tire pressure ................ 8-30
Tire pressure monitoring system
(TPMS) ....................5-3
Types of tires ............... 8-36
Uniform tire quality grading .......9-20
Wheels and tires ............. 8-30
Wheel/tire size ...............9-9
10-6
—
—
07/26/10—dmoore