ad blue INFINITI M35 2006 Factory User Guide

DIAGNOSIS SYSTEM
AV-91
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
Confirmation/Adjustment ModeNKS0048X
1. Start the diagnosis function, and then select “Confirmation/
Adjustment”.
2. Select each screen switch of Confirmation/Adjustment screen to
display the relevant diagnosis screen. Press the “BACK” switch
to return to the initial screen of Confirmation/Adjustment.
DISPLAY DIAGNOSIS
If RGB signal is malfunctioning, the tint of the color bar display is as follows.
SKIB3660E
SKIB3661E
SKIB3662E
R (red) signal error : Light blue (Cyan) tint
G (green) signal error : Purple (Magenta) tint
B (blue) signal error : Yellow tint

AV-96
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
Revision: 2006 January2006 M35/M45
AV COMM CIRCUIT
Amplifier Connection Error
BOSE amp power supply and
ground circuit malfunction is
detected
Malfunction is detected on communi-
cation signal between BOSE amp
and AV (NAVI) control unit
BOSE amp power supply and ground
circuit
BOSE amp
AV (NAVI) control unit
Front Display Connection Error
Front display unit power supply and
ground circuit malfunction is
detected
Malfunction is detected on communi-
cation circuit between front display
unit and AV (NAVI) control unit
Malfunction is detected on communi-
cation signal between front display
unit and AV (NAVI) control unit
Front display unit power supply and
ground
Communication circuit between front
display unit and AV (NAVI) control unit
Front display unit
AV (NAVI) control unit
GPS Antenna ErrorGPS antenna connection malfunction
is detected
GPS antenna feeder
GPS antenna
NAVI control unit
Camera Control Unit Connection ErrorCamera and connection recognition
signal circuit malfunction is detected
Camera-connection recognition signal
circuit
Camera control unit
AV (NAVI) control unit
FLASH-ROM Error Of Control UnitAV (NAVI) control unit malfunction is
detectedReplace AV (NAVI) control unit
Refer to AV-135, "
AV (NAVI) Control Unit"
Connection Of GyroNAVI control unit malfunction is
detectedReplace NAVI control unit
Refer to AV-135, "AV (NAVI) Control Unit"
GPS Communication Error
GPS malfunction is detectedIf the symptoms such as the GPS receipt
malfunction occur, intermittent malfunction
caused by strong radio interference may
be detected.
If the malfunction always occurs, replace
NAVI control unit. GPS ROM Error
GPS RAM Error
GPS RTC Error
DVD-ROM Communication Error
Malfunction is detected on DVD-
ROM drive pickup lens in NAVI con-
trol unit
There is dirt and damage on the map
disc
Map disc
NAVI control unit
Refer to AV-135, "
AV (NAVI) Control
Unit" DVD-ROM Read Error
DVD-ROM Disc Error
DVD-ROM Mechanism not Detected
DVD-ROM Mechanism Error
DVD-ROM Focus Error
DVD-ROM TOC Error
DVD-ROM Seek Error
DVD-ROM Error Correction Error
DVD-ROM Data Transfer Error
DVD-ROM Data Error
DVD-ROM Time-out
DVD-ROM Loading / Eject Error
CAN Controller Memory Error
AV (NAVI) control unit malfunction is
detectedReplace AV (NAVI) control unit
Refer to AV-135, "
AV (NAVI) Control Unit"Bluetooth Module Connection ErrorError item Description Possible cause/Action to take

AV-100
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
Revision: 2006 January2006 M35/M45
BLUETOOTH
Confirm/Change Passkey
The passkey of Bluetooth can be confirmed and changed.
The passkey can be changed by four digits within 0 to 9.
Confirm/Change Device Name
The device name of Bluetooth can be confirmed and changed.
The device name can be changed by sixteen digits within A to Z
(small characters can be used) and - (hyphen).
DELETE UNIT CONNECTION LOG
Erase the connection history of unit and error history that is recorded
in AV (NAVI) control unit (clear the connection history of the removed
unit).
SKIB3669E
SKIB3670E
SKIB3671E

DIAGNOSIS SYSTEM
AV-105
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
DATA MONITOR
When “DATA MONITOR” is selected, “ALL SIGNALS” and “SELEC-
TION FROM MENU” are displayed.
GPS ANTENNA CONN [U1244]GPS antenna connection malfunction
is detected
GPS antenna feeder
GPS antenna
NAVI control unit
CAMERA CONT CONN [U1250]Camera and connection recognition
signal circuit malfunction is detected
Camera-connection recognition signal circuit
Camera control unit
AV (NAVI) control unit
Cont Unit FLASH-ROM [U1200]AV (NAVI) control unit malfunction is
detectedReplace AV (NAVI) control unit
Refer to AV-135, "
AV (NAVI) Control Unit" .
GYRO NO CONN [U1201]NAVI control unit malfunction is
detectedReplace NAVI control unit
Refer to AV-135, "
AV (NAVI) Control Unit" .
GPS COMM [U1204]
GPS malfunction is detectedIf the symptoms such as the GPS receipt mal-
function occur, intermittent malfunction caused
by strong radio interference may be detected.
If the malfunction always occurs, replace NAVI
control unit. GPS ROM [U1205]
GPS RAM [U1206]
GPS RTC [U1207]
DVD-ROM COMM [U1208]
Malfunction is detected on DVD-
ROM drive pickup lens in NAVI con-
trol unit
There is dirt and damage on the map
disc
Map disc
NAVI control unit
Refer to AV-135, "
AV (NAVI) Control Unit" . DVD-ROM READ [U1209]
DVD-ROM DISC [U120A]
DVD-ROM MECHA DETECT [U120C]
DVD-ROM DRIVE MECHA [U120D]
DVD-ROM FOCUS [U120E]
DVD-ROM TOC [U120F]
DVD-ROM SEEK [U1210]
DVD-ROM ERR CORRECTION
[U1211]
DVD-ROM DATA FORWARD [U1212]
DVD-ROM DATA [U1213]
DVD-ROM TIMEOUT [U1214]
DVD-ROM LOAD [U1215]
CAN CONT [U1216]
AV (NAVI) control unit malfunction is
detectedReplace AV (NAVI) control unit
Refer to AV-135, "
AV (NAVI) Control Unit" .
BLUETOOTH CONN [U1217]Error item Description Possible cause/Action to take
SKIB3675E

AV-148
[WITH MOBILE ENTERTAINMENT SYSTEM]
SYSTEM DESCRIPTION
Revision: 2006 January2006 M35/M45
GPS (Global Positioning System)
GPS (Global Positioning System) was developed for and is con-
trolled by the US Department of Defense. The system utilizes GPS
satellites (NAVSTAR), sending out radio waves while flying on an
orbit around the earth at an altitude of approximately 21,000 km
(13,100miles).
The GPS receiver calculates the vehicle's position in three dimen-
sions (latitude/longitude/altitude) according to the time lag of the
radio waves received from four or more GPS satellites (three-dimen-
sional positioning). If radio waves were received only from three
GPS satellites, the GPS receiver calculates the vehicle's position in
two dimensions (latitude/longitude), utilizing the altitude data calcu-
lated previously with radio waves from four or more GPS satellites
(two-dimensional positioning).
Position correction by GPS is not available while the vehicle is stopped.
Accuracy of GPS will deteriorate under the following conditions:
In two-dimensional positioning, GPS accuracy will deteriorate when altitude of the vehicle position
changes.
The accuracy can be even lower depending on the arrangement of the GPS satellites utilized for the posi-
tioning.
Position detection is not possible when vehicle is in an area where radio waves from the GPS satellite do
not reach, such as in a tunnel, parking lot in a building, and under an elevated highway. Radio waves from
the GPS satellites may not be received when some object is located over the GPS antenna.
NOTE:
Even a high-precision three dimensional positioning, the detection result has an error about 10 m (30ft).
Because the signals of GPS satellite is controlled by the Tracking and Control Center in the United States,
the accuracy may be degraded lower intentionally or the radio waves may stop.
MOBILE ENTERTAINMENT SYSTEM
The wireless headphone has been adopted to the rear seat. It is possible to listen to a separate sound in
front seat and rear seat and to see a separate image in front display and rear display.
When headphone mode is turned ON at radio/CD changer mode, AUX or DVD mode is turned ON only for
rear seat. The image that is different from front seat is displayed and a separate sound is output from
speaker and headphone.
HANDS-FREE PHONE
AV (NAVI) control unit has a Bluetooth module. It can perform wireless hands-free telephone calls using
the portable phone in a pocket.
5 or more portable phones can be registered into the AV (NAVI) control unit.
REAR VIEW MONITOR
The small CCD camera is equipped into the rear end of the vehicle. The rear view monitor that displays
the area behind the vehicle while backing up is equipped.
Guiding lines indicating side and rear clearances are provided in the rear view monitor image, which
allows the driver to more easily judge distances between the vehicle and objects in the display. The possi-
ble route lines that indicate the possible route according to the steering angle are provided to help backing
up when parking.
Image quality of the rear view image and of the navigation screen can be adjusted separately.
SEL526V

AV-212
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
46
(L/Y)47
(G)RGB signal (B: blue) Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
47
(G)Ground RGB ground – ON – Approx. 0 V
48
(B)GroundRGB synchronizing sig-
nalOutput ON –
49 – Shield – – – –
50
(G)Ground RGB area (YS) signal Output ONWhen inputting RGB image. Approx. 5 V
Set the selector lever in R
position, and then display
the rear view image.
51
(W)GroundHorizontal synchronizing
(HP) signalInput ON –
52
(R)GroundVertical synchronizing
(VP) signalInput ON –
53
(O/L)GroundCommunication signal
(CONT-DISP)Input ONWhen adjusting display
brightness. Te r m i n a l
(Wire color)
ItemSignal
Input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB2237J
SKIB3603E
PKIB4948J
SKIB3601E
SKIB3598E
PKIB5039J

AV-214
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
Video DistributorNKS004AP
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
SwitchOperation
1
(W)–Communication signal
(H)Input/
Output–– –
2
(R)–Communication signal
(L)Input/
Output–– –
3
(W)–Communication signal
(H)Input/
Output–– –
4
(R)–Communication signal
(L)Input/
Output–– –
6 – Shield – – – –
7
(B/R)GroundComposite synchroniz-
ing signal (front)Output ONFront display
DVD image
8
(BR)GroundComposite image signal
(front)Output ONFront display
DVD image
10
(B)12
(W/L)RGB signal (R: red)
(front)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
11
(W)12
(W/L)RGB signal (G: green)
(front)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
12
(W/L)– RGB ground – ON – Approx. 0 V
13
(R)12
(W/L)RGB signal (B: blue)
(front)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
SKIA0187E
SKIB2251J
SKIB2238J
SKIB2236J
SKIB2237J

AV-216
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
25
(B)27
(G)RGB signal (R: red)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
26
(W)27
(G)RGB signal (G: green)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
27
(G)Ground RGB ground – ON – Approx. 0 V
28
(R)27
(G)RGB signal (B: blue)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
29
(W/R)GroundVertical synchronizing
(VP) signal
(rear)Input ON –
30
(W)GroundHorizontal synchronizing
(HP) signal (rear)Input ON –
31 – Shield – – – –
32
(R/L)GroundRGB area (YS) signal
(rear)Output ONWhen inputting RGB image. Approx. 5 V
Rear display
DVD image Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
SwitchOperation
SKIB2238J
SKIB2236J
SKIB2237J
SKIB0823E
SKIB0825E
PKIB4949J

AV-218
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
46
(L/Y)47
(G)RGB signal (B: blue) Input ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
47
(G)Ground RGB ground – ON – Approx. 0 V
48
(G)Ground RGB area (YS) signal Input ONWhen inputting RGB image. Approx. 5 V
Set the selector lever in R
position, and then display
the rear view image.
49
(W)GroundHorizontal synchronizing
(HP) signalOutput ON –
50
(R)GroundVertical synchronizing
(VP) signalOutput ON –
51
(B)GroundRGB synchronizing sig-
nalInput ON –
52 – Shield – – – –
53
(B)Ground Ground – ON – Approx. 0 V
54
(L)Ground Battery power supply Input OFF – Battery voltage
55
(V)Ground ACC power supply Input ACC – Battery voltage
56
(G)Ground Ignition signal Input ON – Battery voltage
57
(W)GroundRemote control receiver
VCCOutput ON – Approx. 5 V Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
SwitchOperation
SKIB2237J
PKIB4948J
SKIB0825E
SKIB0823E
SKIB0825E

AV-220
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
5
(R)8
(W/L)RGB signal (B: blue) Input ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
6
(O/L)GroundVertical synchronizing
(VP) signalOutput ON –
7
(L/Y)GroundRGB synchronizing sig-
nalOutput ON –
8
(W/L)Ground RGB ground – ON – Approx. 0 V
10 – Shield – – – –
11
(Y)Ground Camera image signal Input ONSet the selector in R posi-
tion, and then display the
rear view image.
12 – Shield – – – –
13
(B/R)GroundComposite synchroniz-
ing signalInput ON –
14 – Shield – – – –
15
(BR)Ground Composite image signal Input ON DVD image Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB2237J
SKIB0823E
SKIB0826E
SKIB0827E
SKIA0187E
SKIB2251J