ignition INFINITI M35 2007 Factory Service Manual

POWER DOOR LOCK SYSTEM
BL-41
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Door Key Cylinder Switch CheckNIS001X6
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-II
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR ROCK SYS-
TEM” with CONSULT-II.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between power window main switch connector and ground.
OK or NG
OK >> Key cylinder switch circuit is OK.
NG >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Disconnect power window main switch and front door key lock assembly (driver side) connector.
2. Check continuity between power window main switch connector and front door lock assembly (driver side)
connector.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
Monitor item Condition
KEY CYL LK-SWLock : ON
Neutral / Unlock : OFF
KEY CYL UN-SWUnlock : ON
Neutral / Lock : OFF
PIIA6285E
Terminals
Key positionVoltage (V)
(Approx.) (+)
(–) Power window
main switch
connectorTerminal
D104
GroundLock 0
Neutral / Unlock 5
6Unlock 0
Neutral / Lock 5
PIIB5956E
AB
Continuity Power window
main switch
connectorTerminalFront door lock
assembly
(driver side)
connectorTerminal
D104
D146
Ye s
65
PIIB5973E

INTELLIGENT KEY SYSTEM
BL-43
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
INTELLIGENT KEY SYSTEMPFP:285e2
Component Parts and Harness Connector LocationNIS001X7
1. Fuse block (J/B) fuse layout 2. Fuse and fusible link box 3. BCM M1, M2, M3 (View with instru-
ment lower panel RH removed)
4. IPDM E/R E9 5. Push-button ignition switch M27
(Push switch)6. Combination meter M52
PIIB5860E

BL-48
INTELLIGENT KEY SYSTEM
Revision: 2007 April2007 M35/M45

When BCM receives the door lock/unlock signal, it operates door lock actuator and flashes the hazard
lamp (lock: 1 time, unlock: 2 times) at the same time as a reminder.
Operation Description/Trunk Open

When the Intelligent Key unit detects that trunk open request switch is pressed, it starts the outside key
antenna (trunk room) and inside key antenna corresponding to the pressed trunk open request switch and
sends the request signal to the Intelligent Key. And then, make sure that the Intelligent Key is near the
trunk.

If the Intelligent Key is within the outside key antenna (trunk room) detection area, it receives the request
signal and sends the key ID signal to the Intelligent Key unit via remote keyless entry receiver.

Intelligent Key unit receives the key ID signal and compares it with the registered key ID.

If the key ID check result is OK, the Intelligent Key unit sends trunk open request signal to BCM (Body
control module) via CAN communication line.

Intelligent Key unit sends the trunk open request signal and sounds Intelligent Key warning buzzer 4 times
at the same time.

When BCM receives the trunk open request signal, it operates the trunk lid opener actuator and opens the
trunk.
Operation Condition
If the following conditions are not satisfied, door lock/unlock or trunk open operations are not performed even
if the request switch is operated.
*: Even with a registered Intelligent Key remain inside the vehicle, door locks can be unlock from outside of the vehicle with a spare Intel-
ligent Key as long as key IDs are different.
Outside Key Antenna Detection Area
The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver and passenger door handles (1). The outside key antenna
detection area of trunk open function is in the range of approximately
80 cm (31.50 in) surrounding Trunk opener request switch (2). How-
ever, this operating range depends on the ambient conditions.
Each request switch operation Operation condition
Lock operation

All doors are closed

Ignition switch is in OFF position

Intelligent Key is out of key slot

Intelligent Key is outside the vehicle

Intelligent Key is within outside key antenna detection area
Unlock Operation

Intelligent Key is outside the vehicle

Intelligent Key is within outside key antenna detection area *
Trunk open operation

Intelligent Key is within outside key antenna (trunk room) detection area*

Trunk cancel switch is ON

Key reminder functions operate (trunk)
PIIB5899E

BL-50
INTELLIGENT KEY SYSTEM
Revision: 2007 April2007 M35/M45
Hazard and buzzer reminder can be changed using “HAZARD ANSWER BACK”, “ANSWER BACK WITH I-
KEY LOCK” and “ANSWER BACK WITH I-KEY UNLOCK” mode in “WORK SUPPORT”.Refer to BL-81,
"WORK SUPPORT" .
Auto Door Lock Function
When all doors are locked, ignition switch is in OFF position and key switch is OFF (Intelligent Key is not
inserted in key slot), doors are unlocked with door request switch
When Intelligent Key unit does not receive the following signals within 60 seconds, all doors are locked.

Door switch is ON (door is opened)

Door is locked

Ignition switch is ON (ignition switch is pressed)

Key switch is ON (Intelligent Key is inserted in key slot)
Auto door lock mode can be changed by “AUTO RELOCK TIMER” mode in “WORK SUPPORT”. Refer to BL-
81, "WORK SUPPORT" .
Room Lamp Operation
When the following conditions are met:

Condition of interior lamp switch is in DOOR position

Door switch OFF (all the doors are closed)
Intelligent Key system turns on interior lamp (for 30 seconds) by receiving UNLOCK signal from door request
switch. For detailed description, refer to LT- 2 6 9 , "
ROOM LAMP TIMER OPERATION" .
List of Operation Related Parts
Parts marked with × are the parts related to operation.
Door lock/trunk open function
Intelligent Key
Key slot
Remote keyless entry receiver
Door switch
Trunk room lamp switch
Door request switch (Driver, Passenger)
Trunk opener request switch
Door lock actuator
Trunk lid opener actuator
Inside key antenna
Outside key antenna (Driver, Passenger)
Outside key antenna (Trunk)
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Hazard warning lamp
Trunk lid opener cancel switch
Push-button ignition switch
Door lock/unlock function by request switch×××××××× ×××
Trunk open function by the trunk opener
request switch××××××××××××
Hazard and buzzer reminder function for door
lock/unlock operation×××××
Buzzer reminder for trunk open operation××××
Key reminder function×××× × × ××××××××
Selective unlock function by request switch
(Driver side)× ×××× ×××
Selective unlock function by request switch
(Passenger side)× ×××× ×××
Auto door lock function××××× ××× ×

BL-52
INTELLIGENT KEY SYSTEM
Revision: 2007 April2007 M35/M45
Hazard and Horn Reminder Function
When doors are locked or unlocked by Intelligent Key, Intelligent Key unit sends hazard and horn request sig-
nal to BCM via CAN communication line.
BCM flashes hazard warning lamps as a reminder and sends horn chirp signal to IPDM E/R. IPDM E/R
sounds horn as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating function of hazard and horn reminder
Hazard and horn reminder does not operate if any door switch is ON (any door is OPEN).
How to change hazard and horn reminder mode
With CONSULT-II
Hazard and horn reminder can be changed using “HORN WITH KEYLESS LOCK” and “HAZARD ANSWER
BACK” mode in “WORK SUPPORT”.Refer to BL-81, "
WORK SUPPORT" .
Without CONSULT-II
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp flashes and horn sounds as follows:
Auto Door Lock Function
When all doors are locked, ignition switch is OFF (ignition switch is not pressed) and key switch is OFF (Intel-
ligent Key is not inserted in key slot), doors are unlocked with Intelligent Key button. When Intelligent Key unit
does not receive the following signals within 30 seconds, all doors are locked.

Door switch is ON (door is opened)

Door is locked

Ignition switch is ON

Key switch is ON (Intelligent Key is inserted in key slot)
Auto door lock mode can be changed by “AUTO RELOCK TIMER” mode in “WORK SUPPORT”. Refer to BL-
81, "WORK SUPPORT" .
Panic Alarm Function
When ignition switch is OFF (ignition switch is not pressed) and key switch is OFF (Intelligent Key is not
inserted in key slot), Intelligent Key unit receives PANIC ALARM signal from Intelligent Key.
Intelligent Key unit sends alarm request signal to BCM via CAN communication line.
BCM turns on and off headlamp intermittently and sends theft warning horn signal to IPDM E/R. Then, IPDM
E/R turns on and off horn intermittently.
The headlamp flashes and the horn sounds intermittently.
The alarm automatically turns off:

After 25 seconds

When Intelligent Key unit receives any signal from Intelligent Key

When door request switch is pressed (Intelligent Key is within the outside key antenna detection area)
Panic alarm function mode can be changed by “PANIC ALARM DELAY” mode in “WORK SUPPORT”. Refer to
BL-81, "
WORK SUPPORT" .
C mode S mode
Intelligent Key operation Lock Unlock Trunk open Lock Unlock Trunk open
Hazard warning lamp flash Twice Once — Twice — —
Horn sound Once—————
SEL153WA

INTELLIGENT KEY SYSTEM
BL-53
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Keyless Power Window Down (Open) Function
All power windows open when the unlock button on Intelligent Key is activated and kept pressed for more than
3 seconds with the ignition switch OFF. The windows keep opening if the unlock button is continuously
pressed.
The power window opening stops when the following operations are performed:

When the unlock button is kept pressed more than 15 seconds.

When the ignition switch is turned ON while the power window opening is operated.

When the unlock button is released.
While retained power operation activate, Keyless power window down (open) Function cannot be operated.
Keyless power window down operation mode can be changed by “P/W DOWN DELAY” mode in “WORK SUP-
PORT”. Refer to BL-81, "
WORK SUPPORT" .
Room Lamp Illumination Operation
When the following conditions are met:

Condition of interior lamp switch is in DOOR position

Door switch OFF (all the doors are closed)
Intelligent Key system turns on interior lamp (for 30 seconds) by receiving UNLOCK signal from Intelligent
Key. For detailed description, refer to LT- 2 6 9 , "
ROOM LAMP TIMER OPERATION" .
List of Operation Related Parts
Parts marked with × are the parts related to operation.
ENGINE START FUNCTION
Refer to BL-125, "INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION" .
Remote keyless entry functions
Intelligent Key
Key slot
Door request switch (Driver, Passenger)
Door switch
Trunk room lamp switch
Door lock actuator
Trunk lid opener actuator
Intelligent Key warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter
Hazard warning lamp
Horn
IPDM E/R
Head lamp
Door lock/unlock function by remote control button×× × × ×××
Trunk open function by remote control button×× × × ×××
Hazard and horn reminder function× ××××××××
Selective unlock function××××××
Keyless power window down (open) function×× ×××
Auto door lock function×× × ×××
Panic alarm function× × ××× ×××

INTELLIGENT KEY SYSTEM
BL-55
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Operation Condition
Once the following condition from below is established, alert or warning will be executed.
Warning/Information functions Operation procedure
Intelligent Key system malfunctionWhen a malfunction is detected on Intelligent Key unit, “KEY” warning lamp
will illuminates.
OFF position warning For internal

Ignition switch: ACC position.

Door switch (driver side): ON (Door is open).
For externalOFF position warning (For internal) is in active mode, driver side door has
been closed.
NOTE:
OFF position (For external) active only when each of the sequence has
occurred as below: P position warning → ACC warning → OFF position warn-
ing (For internal) → OFF position warning (For internal)
P position warning

Shift position: Except P position

Engine is running to stopped (Ignition switch is ON to ACC)
ACC warning

During P position warning is in active mode, shift position has changed P
position.

Ignition switch: Except OFF position.
Take away warningDoor is open to close

Ignition switch: Except OFF position.

Door switch: ON to OFF (Door is open to close).

Intelligent Key can not be detected inside the vehicle.
Door is open

Door switch: ON (Door is open)

Key ID vilification every 5 seconds when registered Intelligent Key can not
be detected inside the vehicle.
Push-ignition switch
operation

Ignition switch: Except OFF position.

Press ignition switch.

Intelligent Key can not be detected inside the vehicle.
Take away through win-
dow

Engine is running.

Key ID vilification every 30 seconds when registered Intelligent Key can not
be detected inside the vehicle.

After vehicle speed verification, the registered Intelligent Key can not be
detect inside the vehicle.
Intelligent Key is
removed from key slot

When Intelligent Key is removed from key slot, Intelligent Key can not be
detected inside the vehicle.
Door lock operation
warningRequest switch operationWhen request switch is pushed (lock operation) under the following condi-
tions.

Door switch: ON (Any door is open).

Intelligent Key is inside vehicle.
Intelligent Key button
operationWhen Intelligent Key bottom is pushed (lock operation) under the following
conditions.

Door switch: ON (Any door is open).

For 3 seconds after Intelligent Key is removed from key slot.
Key warning

Ignition switch is OFF position.

Driver side door switch: ON (Driver side door is open).

Intelligent Key is inserted in key slot.
Intelligent Key insert information

Door switch: ON to OFF (Door is open to close).

Ignition switch: OFF to ON position.

Intelligent Key is out of key slot.

Intelligent Key can not be detected inside the vehicle.

BL-56
INTELLIGENT KEY SYSTEM
Revision: 2007 April2007 M35/M45
Warning Method
The following table shows the alarm or warning methods with chime.
Meter display, “KEY” indicator or key slot illumination when the warning conditions are met.
Engine start informationIgnition switch is ON
position

Ignition switch: ON position.

Shift position: P position

Engine is stopped
Ignition switch is except
ON position

Ignition switch: Except ON position.

Shift position: P position

Intelligent Key is inserted in key slot.

Intelligent Key can be detected inside the vehicle.
Steering lock information When steering lock can not be released after ignition switch is turned ON.
Intelligent Key low battery warningWhen Intelligent Key is low battery, Intelligent Key unit is detected after igni-
tion switch is turned ON.
Key ID warningWhen registered Intelligent Key can not be detected inside the vehicle after
ignition switch is turned ON. Warning/Information functions Operation procedure
Warning/Information functions“KEY” warn-
ing lampCombination meter displayKey slot
illuminationWarning chime
Combination
meter buzzerIntelligent
Key warning
buzzer
Intelligent Key system malfunction Illuminate — — — —
OFF position warn-
ing For internal — — — Activate —
For external — — — — Activate
P position warning — — Activate —
ACC warning — — Activate —
Take away warningDoor is open to
close— Flash Activate Activate
Door is open — Flash — —
Push-ignition
switch operation— Flash Activate —
Take away
through window— Flash Activate —
Intelligent Key is
removed from
key slot—Flash——
Door lock opera-
tion warningRequest switch
operation— — — — Activate
Intelligent Key
operation— — — — Activate
PIIB4765J
PIIB4766J
PIIB6452E

INTELLIGENT KEY SYSTEM
BL-57
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Key warning — Flash Activate —
Intelligent Key insert information — Flash — —
Engine start infor-
mationIgnition switch is
ON position————
Ignition switch is
except ON posi-
tion————
Steering lock information — — — —
Intelligent Key low battery warning — — — —
Key ID warning — — — —Warning/Information functions“KEY” warn-
ing lampCombination meter displayKey slot
illuminationWarning chime
Combination
meter buzzerIntelligent
Key warning
buzzer
PIIB4769J
PIIB4768J
PIIB4771J
PIIB4770J
PIIB4772J
PIIB4774J
PIIB4773J

BL-58
INTELLIGENT KEY SYSTEM
Revision: 2007 April2007 M35/M45
List of Operation Related Parts
Parts marked with × are the parts related to operation.
Warning function
Intelligent Key
Key slot
Ignition switch
Door switch
Door request switch
Inside key antenna
Outside key antenna
Intelligent Key warning buzzer
Combination meter warning buzzer
Intelligent Key unit
CAN communication system
BCM
Combination meter display
Key slot illumination
Park position switch
“KEY” warning lamp
Intelligent Key system malfunction×× ×
OFF position warningFor internal×××××
For external×××××
P position warning××××××
ACC warning××××××
Take away warningDoor is open or close× × × ×××××××
Door is open× × × ×××××
Push-ignition switch
operation× × × ××× ××
Take away through win-
dow×××××××
Intelligent Key is
removed from key slot×× × ×× ××
Door lock operation warning×× ××××× ×××
Key warning×× × ××××××
Intelligent Key insert information×××× × ×××××
Engine start informationIgnition switch is ON
position××× × ×× × ×
Ignition switch is except
ON position××× × ×× ×
Steering lock information××××
Intelligent Key low battery warning×××××
Key ID warning××× × ×× ×