check engine INFINITI M35 2007 Factory Owner's Guide

AT-58
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
3. CHECK “P” POSITION FUNCTIONS
1. Move selector lever to “P” position.
2. Turn ignition switch OFF.
3. Release the parking brake.
4. Push the vehicle forward or backward.
5. Engage the parking brake.
When you push the vehicle with disengaging the parking brake, does it move?
YES >> Enter a check mark at AT- 1 9 1 , "In “P” Position, Vehicle Moves When Pushed" on the AT- 4 8 ,
"DIAGNOSTIC WORKSHEET" , then continue the road test.
NO >> GO TO 4.
4. CHECK “N” POSITION FUNCTIONS
1. Start engine.
2. Move selector lever to “N” position.
3. Release the parking brake.
Does vehicle move forward or backward?
YES >> Enter a check mark at AT- 1 9 2 , "In “N” Position, Vehicle Moves" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
NO >> GO TO 5.
5. CHECK SHIFT SHOCK
1. Engage the brake.
2. Move selector lever to “D” position.
When the A/T is shifted from
“N” to “D”, is there an excessive shock?
YES >> Enter a check mark at AT- 1 9 3 , "Large Shock (“N” to “D” Position)" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
NO >> GO TO 6.
6. CHECK “R” POSITION FUNCTIONS
1. Engage the brake.
2. Move selector lever to “R” position.
3. Release the brake for 4 to 5 seconds.
Does the vehicle creep backward?
YES >> GO TO 7.
NO >> Enter a check mark at AT- 1 9 5 , "
Vehicle Does Not Creep Backward in “R” Position" Position” on
the AT- 4 8 , "
DIAGNOSTIC WORKSHEET" , then continue the road test.
7. CHECK “D” POSITION FUNCTIONS
Inspect whether the vehicle creep forward when the A/T is put into the “D” position.
Does the vehicle creep forward in the
“D” position?
YES >> Go to AT- 5 9 , "Cruise Test - Part 1" , AT- 6 1 , "Cruise Test - Part 2" and AT- 6 1 , "Cruise Test - Part 3"
.
NO >> Enter a check mark at AT- 1 9 7 , "
Vehicle Does Not Creep Forward in “D” Position" on the AT- 4 8 ,
"DIAGNOSTIC WORKSHEET" , then continue the road test.

TROUBLE DIAGNOSIS
AT-59
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
Cruise Test - Part 1NCS001KA
1. CHECK STARTING OUT FROM D1
1. Drive the vehicle for about 10 minutes to warm up the engine oil and ATF.
Appropriate temperature for the ATF: 50 to 80°C (122 to 176°F)
2. Park the vehicle on a level surface.
3. Move selector lever to “P” position.
4. Start the engine.
5. Move selector lever to “D” position.
6. Press the accelerator pedal about half way down to accelerate the vehicle.
With CONSULT-II
Read the gear position. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Starts from D1?
YES >> GO TO 2.
NO >> Enter a check mark at AT- 1 9 9 , "
Vehicle Cannot Be Started from D1" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
2. CHECK SHIFT-UP D1 → D2
Press down the accelerator pedal about half-way and inspect if the vehicle shifts up (D1 → D2) at the appro-
priate speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle degree of opening and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR
MODE" .
Does the A/T shift-up D1
→ D2 at the correct speed?
YES >> GO TO 3.
NO >> Enter a check mark at AT- 2 0 1 , "
A/T Does Not Shift: D1 → D2" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
3. CHECK SHIFT-UP D2 → D3
Press down the accelerator pedal about half-way and inspect if the vehicle shifts up (D2 → D3) at the appro-
priate speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle degree of opening and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR
MODE" .
Does the A/T shift-up D2
→ D3 at the correct speed?
YES >> GO TO 4.
NO >> Enter a check mark at AT- 2 0 3 , "
A/T Does Not Shift: D2 → D3" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
4. CHECK SHIFT-UP D3 → D4
Press down the accelerator pedal about half-way and inspect if the vehicle shifts up (D3 → D4) at the appro-
priate speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle degree of opening and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR
MODE" .
Does the A/T shift-up D3
→ D4 at the correct speed?
YES >> GO TO 5.
NO >> Enter a check mark at AT- 2 0 5 , "
A/T Does Not Shift: D3 → D4" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.

AT-60
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
5. CHECK SHIFT-UP D4 → D5
Press down the accelerator pedal about half-way and inspect if the vehicle shifts up (D4 → D5) at the appro-
priate speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle degree of opening and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR
MODE" .
Does the A/T shift-up D4
→ D5 at the correct speed?
YES >> GO TO 6.
NO >> Enter a check mark at AT- 2 0 7 , "
A/T Does Not Shift: D4 → D5" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
6. CHECK LOCK-UP
When releasing accelerator pedal (closed throttle position signal: OFF) from D5, check lock-up from D5 to L/U.
Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Select “TCC SOLENOID” with the “MAIN SIGNAL” mode for “A/T”. Refer to AT- 9 0 , "
CONSULT-II REFER-
ENCE VALUE" .
Does it lock-up?
YES >> GO TO 7.
NO >> Enter a check mark at AT- 2 0 9 , "
A/T Does Not Lock-up" on the AT- 4 8 , "DIAGNOSTIC WORK-
SHEET" , then continue the road test.
7. CHECK LOCK-UP HOLD
Check hold lock-up.
With CONSULT-II
Select “TCC SOLENOID” with the “MAIN SIGNAL” mode for “A/T”. Refer to AT- 9 0 , "
CONSULT-II REFER-
ENCE VALUE" .
Does it maintain lock-up status?
YES >> GO TO 8.
NO >> Enter a check mark at AT- 2 1 0 , "
A/T Does Not Hold Lock-up Condition" on the AT- 4 8 , "DIAGNOS-
TIC WORKSHEET" , then continue the road test.
8. CHECK LOCK-UP RELEASE
Check lock-up cancellation by depressing brake pedal lightly to decelerate.
With CONSULT-II
Select “TCC SOLENOID” with the “MAIN SIGNAL” mode for A/T. Refer to AT- 9 0 , "
CONSULT-II REFERENCE
VA L U E" .
Does lock-up cancel?
YES >> GO TO 9.
NO >> Enter a check mark at AT- 2 1 2 , "
Lock-up Is Not Released" on the AT- 4 8 , "DIAGNOSTIC WORK-
SHEET" , then continue the road test.
9. CHECK SHIFT-DOWN D5 → D4
Decelerate by pressing lightly on the brake pedal.
With CONSULT-II
Read the gear position and engine speed. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
When the A/T shift-down D5
→ D4, does the engine speed drop smoothly back to idle?
YES >> 1. Stop the vehicle.
2. Go to AT- 6 1 , "
Cruise Test - Part 2" .
NO >> Enter a check mark at AT- 2 1 2 , "
Engine Speed Does Not Return to Idle" on the AT- 4 8 , "DIAG-
NOSTIC WORKSHEET" , then continue the road test. Go to AT- 6 1 , "Cruise Test - Part 2" .

TROUBLE DIAGNOSIS
AT-61
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
Cruise Test - Part 2NCS001KB
1. CHECK STARTING FROM D1
1. Move selector lever to “D” position.
2. Accelerate at half throttle.
With CONSULT-II
Read the gear position. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Does it start from D1?
YES >> GO TO 2.
NO >> Enter a check mark at AT- 1 9 9 , "
Vehicle Cannot Be Started from D1" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
2. CHECK SHIFT-UP D1 → D2
Press the accelerator pedal down all the way and inspect whether or not the A/T shifts up (D1 → D2) at the
correct speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle position and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Does the A/T shift-up D1
→ D2 at the correct speed?
YES >> GO TO 3.
NO >> Enter a check mark at AT- 2 0 1 , "
A/T Does Not Shift: D1 → D2" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
3. CHECK SHIFT-UP D2 → D3
Press the accelerator pedal down all the way and inspect whether or not the A/T shifts up (D2 → D3) at the
correct speed. Refer to AT- 6 3 , "
Vehicle Speed at Which Gear Shifting Occurs" .
With CONSULT-II
Read the gear position, throttle position and vehicle speed. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Does the A/T shift-up D2
→ D3 at the correct speed?
YES >> GO TO 4.
NO >> Enter a check mark at AT- 2 0 3 , "
A/T Does Not Shift: D2 → D3" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test.
4. CHECK SHIFT-UP D3 → D4 AND ENGINE BRAKE
When the A/T changes speed D3 → D4, return the accelerator pedal.
With CONSULT-II
Read the gear position. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Does the A/T shift-up D3
→ D4 and apply the engine brake?
YES >> 1. Stop the vehicle.
2. Go to AT- 6 1 , "
Cruise Test - Part 3" .
NO >> Enter a check mark at AT- 2 0 5 , "
A/T Does Not Shift: D3 → D4" on the AT- 4 8 , "DIAGNOSTIC
WORKSHEET" , then continue the road test. Go to AT- 6 1 , "Cruise Test - Part 3" .
Cruise Test - Part 3NCS001KC
1. MANUAL MODE FUNCTION
Move to manual mode from “D” position.
Does it switch to manual mode?
YES >> GO TO 2.
NO >> Continue road test and add check mark to AT- 2 1 3 , "
Cannot Be Changed to Manual Mode" on AT-
48, "DIAGNOSTIC WORKSHEET" .

AT-62
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
2. CHECK SHIFT-DOWN
During manual mode driving, is downshift from M5 → M4 → M3 → M2 → M1 performed?
With CONSULT-II
Read the gear position. Refer to AT- 9 6 , "
DATA MONITOR MODE" .
Is downshifting correctly performed?
YES >> GO TO 2.
NO >> Enter a check mark at “A/T Does Not Shift” at the corresponding position (5th → 4th, 4th → 3rd,
3rd → 2nd, 2nd → 1st) on the AT- 4 8 , "
DIAGNOSTIC WORKSHEET" , then continue the road test.
3. CHECK ENGINE BRAKE
Check engine brake.
Does engine braking effectively reduce speed in M1 position?
YES >> 1. Stop the vehicle.
2. Perform self-diagnostics. Refer to AT- 9 2 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 ,
"Diagnostic Procedure without CONSULT-II" .
NO >> Enter a check mark at AT- 2 2 0 , "
Vehicle Does Not Decelerate by Engine Brake" on the AT- 4 8 ,
"DIAGNOSTIC WORKSHEET" , then continue trouble diagnosis.

AT-64
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
AW D M OD E LS

At closed throttle, the accelerator opening is less than 1/8 condition. (Closed throttle position signal: OFF)

At half throttle, the accelerator opening is 4/8 of the full opening.
Symptom ChartNCS001KF

The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.

Overhaul and inspection inside the A/T only if A/T fluid condition is NG. Refer to AT- 5 3 , "A/T Fluid Condi-
tion Check" .
Engine model VQ35DE
Throttle positionVehicle speed km/h (MPH)
Lock-up ON Lock-up OFF
Closed throttle 51 - 59 (32 - 37) 48 - 56 (30 - 35)
Half throttle 188 - 196 (117 - 122) 132 - 140 (82 - 87)
No. Item Symptom Condition Diagnostic ItemReference
page
1Shift
ShockLarge shock. (“N” →
“D” position)
Refer to AT-193,
"Large Shock (“N” to
“D” Position)" .ON vehicle1. Engine idle speedEC-83
(for
VQ35DE
engine),
EC-785

(for
VK45DE
engine)
2. Engine speed signalAT- 1 2 4
3. Accelerator pedal position sensorAT- 1 3 2
4. A/T positionAT- 2 2 7
5. A/T fluid temperature sensorAT- 1 3 5
6. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 2,
AT- 1 5 1
7. CAN communication lineAT- 1 0 5
8. A/T fluid level and stateAT- 5 3
9. Line pressure testAT- 5 5
10. Control valve with TCMAT- 2 3 6
OFF vehicle11. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-17, "Cross-Sectional View (VQ35DE Models for 2WD)" , AT-18,
"Cross-Sectional View (VK45DE Models for 2WD)" o r AT-19,
"Cross-Sectional View (AWD Models)" .)AT- 3 0 1

AT-90
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
CONSULT-II Function (A/T)NCS001KH
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
FUNCTION
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man-
ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
Diagnostic test mode Function Reference page
Self-diagnostic results Self-diagnostic results can be read and erased quickly.AT- 9 2
Data monitor Input/Output data in the ECU can be read.AT- 9 6
CAN diagnostic support
monitorThe results of transmit/receive diagnosis of CAN communication can be read.AT- 1 0 0
Function testPerformed by CONSULT-II instead of a technician to determine whether each system
is “OK” or “NG”.—
DTC work support Select the operating condition to confirm Diagnostic Trouble Codes.AT- 1 0 0
ECU part number ECU part number can be read. —
Item name Condition Display value
(Approx.)
VHCL/S SE-A/T
During drivingApproximately
matches the speed
meter reading. VHCL/S SE-MTR
ACCELE POSIReleased accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8.0/8
CLSD THL POSReleased accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POSFully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SWDepressed brake pedal. ON
Released brake pedal. OFF
ENGINE SPEED Engine runningClosely matches the
tachometer reading.
TURBINE REV During driving (lock-up ON)Approximately
matches the engine
speed.
ATF TEMP SE 1
0°C (32° F) - 20°C (68°F) - 80°C (176°F)3.3 - 2.7 - 0.9 V
ATF TEMP SE 23.3 - 2.5 - 0.7 V
TCC SOLENOID Lock-up is active 0.4 - 0.6 A
LINE PRES SOL During driving 0.2 - 0.6 A

AT-92
TROUBLE DIAGNOSIS
Revision: 2007 April2007 M35/M45
CONSULT-II SETTING PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure" .
SELF-DIAGNOSTIC RESULT MODE
After performing self-diagnosis, place check marks for results on the AT- 4 8 , "DIAGNOSTIC WORKSHEET" .
Reference pages are provided following the items.
Operation Procedure
1. Touch “SELF-DIAG RESULTS” on “SELECT DIAG MODE”
screen.
Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
BCIA0031E
Items (CONSULT-
II screen terms)Malfunction is detected when...TCM self-
diagnosisOBD-II (DTC)
Reference
page
“A/T” with
CONSULT-IIMIL indicator
lamp*1,
“ENGINE” with
CONSULT-II or
GST
CAN COMM CIR-
CUIT

When TCM is not transmitting or receiving CAN communi-
cation signal for 2 seconds or more.U1000 U1000AT-105
STARTER RELAY/
CIRC

If this signal is ON other than in “P” or “N” position, this is
judged to be a malfunction.
(And if it is OFF in “P” or “N” position, this too is judged to
be a malfunction.)P0615 —AT-108
TCM
TCM is malfunctioning P0700 P0700AT- 11 2
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern.

“P” position is detected from “N” position without any other
position being detected in between.P0705 P0705AT- 11 3
TURBINE REV S/
CIRC

TCM does not receive the proper voltage signal from the
sensor.

TCM detects an irregularity only at position of 4th gear for
turbine revolution sensor 2.P0717 P0717AT- 11 7
VEH SPD SEN/
CIR AT

Signal from vehicle speed sensor A/T (revolution sensor)
not input due to cut line or the like.

Unexpected signal input during running.

After ignition switch is turned ON, unexpected signal input
from vehicle speed sensor MTR before the vehicle starts
moving.P0720 P0720AT- 11 9
ENGINE SPEED
SIG
TCM does not receive the CAN communication signal from
the ECM.P0725 P0725*3AT-124
TCC SOLENOID/
CIRC
Normal voltage not applied to solenoid due to cut line,
short, or the like.P0740 P0740AT-126
A/T TCC S/V
FNCTN
A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value
with slip rotation.P0744 P0744*2AT-128

TROUBLE DIAGNOSIS
AT-103
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
Diagnostic Procedure without CONSULT-IINCS001KI
OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST)
Refer to EC-135, "Generic Scan Tool (GST) Function" (for VQ35DE engine), EC-838, "Generic Scan Tool
(GST) Function" (for VK45DE engine).
OBD-II SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Refer to EC-70, "Malfunction Indicator Lamp (MIL)" (for VQ35DE engine), EC-772, "Malfunction Indicator
Lamp (MIL)" (for VK45DE engine).
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Description
As a method for locating the suspect circuit, when the self-diagnostics start signal is input, the memory for the
malfunction location is output and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Operation Procedure
1. CHECK A/T CHECK INDICATOR LAMP
1. Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2. Turn ignition switch ON and OFF at least twice, then leave it in the OFF position.
3. Wait 10 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES >> GO TO 2.
NO >> GO TO AT- 1 9 0 , "
A/T CHECK Indicator Lamp Does Not Come On" .
2. JUDGEMENT PROCEDURE
1. Turn ignition switch OFF.
2. Keep pressing shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal ON.)
5. Depress brake pedal. (Stop lamp switch signal ON.)
6. Turn ignition switch ON.
7. Wait 3 seconds.
8. Move the selector lever to the manual shift gate side. (Manual mode signal ON.)
9. Release brake pedal. (Stop lamp switch signal OFF.)
10. Move the selector lever to “D” position. (Manual mode signal OFF.)
11. Depress brake pedal. (Stop lamp switch signal ON.)
12. Release brake pedal. (Stop lamp switch signal OFF.)
13. Depress accelerator pedal fully and release it.
>> GO TO 3.
3. CHECK SELF-DIAGNOSIS CODE
Check A/T CHECK indicator lamp.
Refer to AT- 1 0 4 , "
Judgement Self-diagnosis Code" .
If the system does not go into self-diagnostics. Refer to AT- 11 3 , "
DTC P0705 PARK/NEUTRAL POSITION
SWITCH" , AT- 1 8 4 , "CLOSED THROTTLE POSITION AND WIDE OPEN THROTTLE POSITION CIRCUIT" ,
AT- 1 6 7 , "
DTC P1815 MANUAL MODE SWITCH" , AT- 1 8 5 , "BRAKE SIGNAL CIRCUIT" .
>>DIAGNOSIS END

DTC U1000 CAN COMMUNICATION LINE
AT-107
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2007 April2007 M35/M45
TCM terminals and data are reference value. Measured between each terminal and ground.
Diagnostic ProcedureNCS001KO
1. CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-II
1. Turn ignition switch ON and start engine.
2. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II.
Is any malfunction of the
“CAN COMM CIRCUIT” indicated?
YES >> Print out CONSULT-II screen, GO TO LAN section.
Refer to LAN-50, "
CAN System Specification Chart" .
NO >>INSPECTION END
Terminal Item Condition Data (Approx.)
3CAN-H – –
8CAN-L – –
PCIA0061E