INFINITI M35 2007 Factory Service Manual

SE-62
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
2. CHECK HARNESS CONTINUITY
1. Disconnect automatic drive positioner control unit connector and telescopic sensor connector.
2. Check continuity harness between automatic drive positioner
control unit connector and telescopic sensor connector.
3. Check continuity harness between automatic drive positioner
control unit connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT
1. Connect automatic drive positioner control unit connector.
2. Check voltage between automatic drive position control unit connector and ground.
OK or NG
OK >> Replace telescopic sensor.
NG >> Replace automatic drive positioner control unit.
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lTelescopic sensor
connectorTerminal
M6 23
M442
Ye s
M733 1
41 3
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M6 23
No
M733
41
PIIB6160E
Terminals
Voltage (V)
(Approx.) (+)
(–) Automatic drive
positioner control
unit connectorTerminal
M6 23 Ground 5
PIIB6159E

AUTOMATIC DRIVE POSITIONER
SE-63
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Tilt Sensor Circuit NIS0026I
1. CHECK TILT SENSOR
With CONSULT-II
With “TILT SEN” on the DATA MONITOR, operate the tilt switch to make sure voltage changes.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Tilt sensor circuit is OK.
NG >> GO TO 2.
Monitor item
[OPERATION or UNIT]Contents
TILT SEN “V”The tilt position (voltage) judged from the tilt sensor sig-
nal is displayed.
PIIA0295E
Automatic
drive posi-
tioner con-
trol unit
connectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (–)
M6 7 GroundTilt top position 1
Tilt bottom position 3.8
PIIB6161E

SE-64
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
2. CHECK HARNESS
1. Disconnect automatic drive positioner control unit connector and tilt sensor connector.
2. Check continuity harness between automatic drive positioner control unit connector and tilt sensor con-
nector.
3. Automatic drive positioner control unit connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT
1. Connect automatic drive positioner control unit connector.
2. Check voltage between automatic drive position control unit connector and ground.
OK or NG
OK >> Replace telescopic sensor.
NG >> Replace automatic drive positioner control unit.
Check Door Mirror Sensor LH CircuitNIS0026J
1. CHECK DOOR MIRROR FUNCTION
Check the following items.
Operation malfunction in memory operation.
NOTE:
If a door mirror face position is set to an implausible angle, the set position may not be reproduced.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace the malfunctioning parts, and check the symptom again.
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lTilt sensor
connectorTerminal
M6 7
M372
Ye s
M733 3
41 1
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M6 7
No
M733
41
PIIB6162E
Terminals
Voltage (V)
(Approx.) (+)
(–) Automatic drive
positioner control
unit connectorTerminal
M6 7 Ground 5
PIIB6161E

AUTOMATIC DRIVE POSITIONER
SE-65
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
2. CHECK DOOR MIRROR LH SENSOR
With CONSULT–II
Check that “VOLTAGE” is displayed on “MIR/SE LH R–L, MIR/SE LH U–D” in the DATA MONITOR.
Without CONSULT–II
1. Turn ignition switch to ACC.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Mirror sensor LH circuit is OK.
NG >> GO TO 3.
Monitor item
[OPERATION or UNIT]Contents
MIR/
SEN LH R–L“V”Voltage output from door mirror LH sensor (LH/
RH) is displayed.
MIR/
SEN LH U–D“V”Voltage output from door mirror LH sensor (UP/
DOWN) is displayed.
PIIB6495E
Automatic
drive posi-
tioner con-
trol unit
connectorTe r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
M622
GroundMirror motor is
operated LEFT or
RIGHTChanges between
3.5 (close to right edge) –
0.5 (close to left edge)
6Mirror motor is
operated UP or
DOWN Changes between
4.2 (close to peak) – 0.5
(close to valley)
PIIB6163E

SE-66
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector and door mirror LH connector.
3. Check continuity between automatic drive positioner control unit
connector and door mirror LH connector.
4. Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK HARNESS CONTINUITY 2
1. Check continuity between automatic drive positioner control unit
connector and door mirror LH connector.
2. Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> Replace door mirror LH.
NG >> Repair or replace harness.
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lDoor mirror LH
connectorTerminal
M733
D211
Ye s
41 12
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M733
No
41
PIIB6164E
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lDoor mirror LH
connectorTerminal
M66
D29
Ye s
22 10
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M66
No
22
PIIB6165E

AUTOMATIC DRIVE POSITIONER
SE-67
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Door Mirror Sensor RH CircuitNIS0026K
1. CHECK DOOR MIRROR FUNCTION
Check the following items.
Operation malfunction in memory operation.
NOTE:
If a door mirror face position is set to an implausible angle, the set position may not be reproduced.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace the malfunctioning parts, and check the symptom again.
2. CHECK DOOR MIRROR RH SENSOR
With CONSULT–II
Check that “VOLTAGE” is displayed on “MIR/SE RH R–L, MIR/SE RH U–D” in the DATA MONITOR.
Without CONSULT–II
1. Turn ignition switch to ACC.
2. Check voltage between automatic drive positioner control unit connector and ground.
OK or NG
OK >> Mirror sensor RH circuit is OK.
NG >> GO TO 3.
Monitor item
[OPERATION or UNIT]Contents
MIR/
SEN RH R–L“V”Voltage output from door mirror RH sensor (LH/
RH) is displayed.
MIR/
SEN RH U–D“V”Voltage output from door mirror RH sensor (UP/
DOWN) is displayed.
PIIB6495E
Automatic
drive posi-
tioner con-
trol unitTerminals
ConditionVoltage (V)
(Approx.)
(+) (–)
M621
GroundMirror motor is
operated UP or
DOWNChanges between
3.5 (close to left edge) –
0.5 (close to right edge)
5Mirror motor is
operated UP or
DOWN Changes between
4.2 (close to peak) –
0.5 (close to valley)
PIIB6166E

SE-68
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector and door mirror RH connector.
3. Check continuity between automatic drive positioner control unit connector and door mirror RH connector.
4. Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK HARNESS CONTINUITY 2
1. Check continuity between automatic drive positioner control unit connector and door mirror RH connector.
2. Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> Replace door mirror RH.
NG >> Repair or replace harness.
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lDoor mirror RH
connectorTerminal
M733
D3911
Ye s
41 12
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M733
No
41
PIIB6164E
AB
Continuity Automatic drive
positioner control
unit connectorTe r m i n a lDoor mirror RH
connectorTerminal
M65
D399
Ye s
21 10
A
GroundContinuity Automatic drive posi-
tioner control unit con-
nectorTerminal
M65
No
21
PIIB6167E

AUTOMATIC DRIVE POSITIONER
SE-69
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Sliding Switch Circuit NIS0026L
1. CHECK FUNCTION
With CONSULT-II
With “SLIDE SW-FR, SLIDE SW-RR” on the DATA MONITOR, oper-
ate the sliding switch to check ON/OFF operation.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between driver seat control unit connector and
ground.
OK or NG
OK >> Sliding switch circuit is OK.
NG >> GO TO 2.
Monitor item [OPER-
ATION or UNIT]Contents
SLIDE SW–
FR"ON/
OFF"ON / OFF status judged from the sliding switch (FR) sig-
nal is displayed.
SLIDE SW–
RR"ON/
OFF"ON / OFF status judged from the sliding switch (RR) sig-
nal is displayed.
PIIA0313E
Driver seat
control unit
connectorTe r m i n a l
ConditionVoltage (V)
(Approx.)
(+) (–)
B20411
GroundSliding switch ON
(BACKWARD
operation)0
Other than above Battery voltage
26Sliding switch ON
(FORWARD
operation)0
Other than above Battery voltage
PIIB6168E

SE-70
AUTOMATIC DRIVE POSITIONER
Revision: 2007 April2007 M35/M45
2. CHECK SLIDING SWITCH CIRCUIT HARNESS CONTINUITY
1. Disconnect driver seat control unit connector and power seat switch connector.
2. Check continuity between driver seat control unit connector and
power seat switch connector.
3. Check continuity between driver seat control unit connector and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK SLIDING SWITCH
Check continuity between power seat switch terminals.
OK or NG
OK >> Replace driver seat control unit.
NG >> Replace power seat switch.
AB
Continuity
Driver seat control
unit connectorTe r m i n a lPower seat switch
connectorTerminal
B20411
B21311
Ye s
26 26
A
GroundContinuity
Driver seat control unit
connectorTerminal
B20411
No
26
PIIB6169E
Power seat
switchTerminal Condition Continuity
B21311
32Sliding switch ON
(BACKWARD operation)Ye s
Other than above No
26Sliding switch ON
(FORWARD operation)Ye s
Other than above No
PIIB6170E

AUTOMATIC DRIVE POSITIONER
SE-71
C
D
E
F
G
H
J
K
L
MA
B
SE
Revision: 2007 April2007 M35/M45
Check Reclining Switch Circuit NIS0026M
1. CHECK FUNCTION
With CONSULT-II
With “RECLN SW-FR, RECLN SW-RR” on the DATA MONITOR,
operate the reclining switch to check ON/OFF operation.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between driver seat control unit connector and
ground.
OK or NG
OK >> Reclining switch circuit is OK.
NG >> GO TO 2.
Monitor item [OPERA-
TION or UNIT]Contents
RECLN SW
–FR“ON/
OFF”ON/OFF status judged from the reclining switch (FR)
signal is displayed.
RECLIN S
W–RR“ON/
OFF”ON/OFF status judged from the reclining switch (RR)
signal is displayed.
PIIA0313E
Driver seat
control unitTerminals
ConditionVoltage (V)
(Approx.)
(+) (–)
B20412
GroundReclining switch ON
(BACKWARD
operation)0
Other than above Battery voltage
27Reclining switch ON
(FORWARD
operation)0
Other than above Battery voltage
PIIB6171E