ECO mode INFINITI Q50 2015 Quick Reference Guide

7
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Flat Tire Visit Dealer or Tire Pressure Low —
Add Air warning message will appear in the vehicle
information display
1 and the low tire pressure
warning light 2 will illuminate when one or more
tires are low in pressure and air is needed.
• The tire pressures should be checked when
the tires are cold. The tires are considered cold
after the vehicle has been parked for 3 hours
or more or driven less than 1 mi (1.6 km) at
moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tire to the recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire, and within a few seconds, the hazard warning lights will
start flashing.
4. When the designated tire pressure is reached, the horn will beep once and the hazard
warning flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 mph (25 km/h). The
Flat Tire Visit Dealer or Tire Pressure Low — Add Air warning message and low tire pressure
warning light will extinguish.

When the low tire pressure warning light flashes for 1 minute and then remains on, the
TPMS is not functioning properly. Have the system checked by an INFINITI retailer.

Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and
the outside temperature. Low outside temperature can lower the temperature of the air
inside the tire, which can cause a lower tire inflation pressure. This may cause the low tire
pressure warning light to illuminate. If the warning light illuminates, check the tire pressure
in your tires.
• Check the tire pressure (including the spare tire) often and always prior to long
distance trips.

The Tire and Loading Information label contains valuable information. Please refer to the
“Technical and consumer information (section 9)” in your Owner’s Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
essential information
1
2
2045927_15c_Infiniti_Q50_QRG_071415.indd 77/14/15 3:38 PM

13
Heated Seats (if so equipped)
There are two ways to operate the heated seats:
1. Press the heated seat switch

1.
• Every press of the switch allows you to
cycle through the five different modes of
AUTO – High – Mid – Low – OFF.
2. While on the CLIMATE control screen on the lower
display, touch the left or right heated seat icon
2.
• The Left or Right Heater Settings screen is
displayed with a list of the five different modes of
AUTO – High – Mid – Low – OFF.
• The indicator light on the heated seat switch

1
will illuminate when the system is in AUTO – High – Mid – Low.
• While in AUTO, the heated seats will turn on and off automatically, depending on
temperature conditions in the vehicle compartment.
• To view which of the five modes the system is in, press the CLIMATE button

3. This
will bring up the CLIMATE control screen on the lower display. From here, you will see
the heated seat icons
2 for the driver’s and passenger’s side, and below the icon is
the mode the system is in currently.
For more information, refer to the “Heater and air conditioner (section 3)” of your InTouch Owner’s Manual.
2 2
3
1 1
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner memory.

Follow this procedure to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Press the ignition switch to the ON position.
• Adjust the driver’s seat, steering column and outside mirrors to the desired positions
using the adjusting switches for each feature.
• Push the SET switch and within 5 seconds push the memory switch (1 or 2) for at
least 1 second.
• The indicator light on the memory switch you select will illuminate for approximately
5 seconds and a buzzer will sound.
• The driver’s seat, steering column and outside mirror positions are now set to
your preferences.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
2045927_15c_Infiniti_Q50_QRG_071415.indd 137/14/15 3:39 PM

21
Intelligent Cruise Control (ICC) (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set vehicle-to-vehicle distance control mode,
press the
button
1 for less than 1.5 seconds.
The gray indicator light 2 will illuminate.

Accelerate to the desired speed.

Push down on the SET – switch
3 and release it.
Intelligent Cruise Control will be set to the
desired speed.

Press the distance button
4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed
indicator lights will illuminate

5 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate

6 in
set mode.

To reset at a faster cruising speed, push up and hold
the RES + switch
7. When the vehicle attains the
desired speed, release the switch.

To reset at a slower cruising speed, push down and
hold the SET – switch

3. Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8. The set vehicle speed indicator
5 will change to grey.

To turn off Intelligent Cruise Control, press the button
1. The indicator light 2 in
the instrument panel will extinguish.
To set conventional (fixed speed) cruise control mode:

While Intelligent Cruise Control is off, press the button
1 and hold it down for more
than 1.5 seconds. The grey indicator light will illuminate.

Accelerate to the desired speed.

Push down on the SET – switch and release it. The green indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
2
5
6
1 8
4
7
3
2045927_15c_Infiniti_Q50_QRG_071415.indd 217/14/15 3:39 PM

22
system guide
Bluetooth® Hands-free Phone System
A cellular telephone should not be used while driving
so full attention may be given to vehicle operation.*
SYSTEM OPERATING TIPS

Press the button on the steering wheel to activate
voice recognition.

Press the button to interrupt the voice prompts at

any time and speak a command after the tone.

To use the system faster, you may speak the second
level commands with the main menu command on the
main menu.

To decrease or increase the volume of the voice
prompts, push the volume control switches
or

on the steering wheel or turn the (power) button/
VOL (volume) control knob on the audio system
while the system is responding.
Bluetooth®
Controls
Microphone
*Some jurisdictions prohibit the use of cellular telephones while driving.
Vehicle Information Display
When the or button 1 is pressed,
the following modes will appear on the vehicle
information display
2:
• Fuel Economy – Displays the current
fuel consumption.
• Average Speed – Displays the average vehicle
speed since the last reset.
• Distance/Time – Displays the elapsed time and
total distance the vehicle has been driven since
the last reset.
• RANGE – Displays the estimated distance to empty
(dte) the vehicle can be driven before refueling.
• Navigation (if so equipped) – Displays the
navigation route information when route guidance is set in the navigation system.
• Audio – Displays the status of the audio information.
• Driving Aids (if so equipped) – Displays driving aid status.
• Tire Pressure (if so equipped) – Displays the current tire pressure in each tire.
• Chassis Control – Displays the status of Active Lane Control and Active Trace Control.
• Warning – Displays when a warning is present.

Push the TRIP RESET switch
3 for approximately 1 second to reset the currently displayed
trip odometer to zero.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
2
3
1
2045927_15c_Infiniti_Q50_QRG_071415.indd 227/14/15 3:40 PM

23


The Voice Recognition system allows you to choose between voice input and manual
control of lists. Choose the method that is easiest for you. For example, when a list is
shown, you can use the
switch and push the OK switch on the steering wheel to
select an item from the displayed list instead of saying the item.

When using the feature to navigate lists during Voice Recognition, use the spoken
menu readout feature to help navigate the list easily. Voice input is paused when menu
control is activated. To resume Voice Recognition, select a menu item by pushing the

switch or simply push the button.

Reduce background noise as much as possible by closing windows and pointing HVAC
vents away from the ceiling.

After the tone, speak naturally without long pauses and without raising your voice.

When speaking phonebook names, use a full name (e.g., Michael Smith) or first
name (e.g., Michael).

To cancel a Voice Recognition session, say “Exit” or press and hold the button
for 5 seconds.

To go back to the previous command, say “Go back”.

For more detailed information and instructions, refer to your cellular phone’s Owner’s
Manual and visit www.InfinitiUSA.com/bluetooth.
CONNECTING PROCEDURE

The vehicle must be stationary when connecting the phone.
1. Press the MENU button below the lower display
and touch the Settings key.
2. Touch Bluetooth.
3. Touch Connect Device and then touch Add New.
4. Initiate connecting from the phone.
• The connecting procedure varies according
to each cellular phone model. For detailed
connecting instructions and a list of
compatible phones, please visit
www.InfinitiUSA.com/bluetooth.
• When prompted for a PIN, enter the PIN that
appears on the screen into the handset.
5. When connecting is complete, the screen will
return to the previous screen.
2045927_15c_Infiniti_Q50_QRG_071415.indd 237/14/15 3:40 PM