light INFINITI Q60 COUPE 2020 Quick Reference Guide

2
Cockpit Overview
Vehicle information display switches
Intelligent Cruise Control switches (if so equipped)
Wiper and washer switch
Paddle shifters (if so equipped)
Combined turn signal/Headlight control switch
Upper display control switches
Audio and Bluetooth® control switches
Instrument brightness control switches and Trip Reset switch
(behind steering wheel)

8
Two positions for the driver’s seat, steering column and outside mirrors can be stored in
the automatic drive positioner memory. To set a memory position:
1. Place the ignition switch in the ON position. (The vehicle should be stopped while
setting the memory.)
2. Adjust the driver’s seat, steering column
and outside mirrors to the desired
positions using the adjusting switches
for each feature.
3. Push the SET switch
, and within 5
seconds, push the memory switch (1 or 2)
. The indicator light for the memory
switch you select will illuminate for
approximately 5 seconds and a chime will
sound when the memory is stored.
The steering column will automatically move when the driver’s side door is
opened to allow the driver to get in and out of the driver’s seat more easily.
“Lift Steering upon Exit” and “Slide Driver Seat Back on Exit” can be adjusted in the
lower touch-screen display under “Comfort & Convenience”.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
Automatic Drive Positioner
(if so equipped)Starting/Stopping
the Engine
It is important to make sure
the INFINITI Intelligent Key
is with you (that is, in your
pocket or purse).
1. Depress the brake pedal.
2. Push the ignition switch
START/STOP button to
the ON position.
TURNING THE ENGINE OFF
1. Move the shift lever to the P (PARK) position
and apply the parking brake.
2. Push the ignition switch START/STOP button
to turn the engine off.
Please see your Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.

9
AUTOMATIC ANTI-GLARE REARVIEW MIRROR
The inside mirror is designed so that it automatically dims during night-time
conditions and according to the intensity of the headlights of the vehicle following
you. The automatic anti-glare feature is activated when the ignition switch is in
the ON position.
• The indicator light
will illuminate when the automatic anti-glare
feature is operating.
• To turn off the anti-glare feature, press the O button on the rearview mirror. The
indicator light will turn off.
• To turn on the anti-glare feature, press the | button on the rearview mirror. The
indicator light
will turn on.
PROGRAMING THE HOMELINK
® UNIVERSAL TRANSCEIVER:
1. Position the handheld transceiver 1-3 in (26-76 mm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
2. Press and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and then rapidly.
3. Both buttons may be released when the indicator light flashes rapidly.
4. Press and hold the programed HomeLink button and observe the indicator light. A solid, continuous light indicates the programing is complete. If
the indicator light rapidly blinks for two seconds and then turns to a solid, continuous light, continue with steps for a rolling code device.
5. At the receiver located on the garage door opener motor, locate the “learn” or “smart” button. If there is difficulty locating the button, reference the
garage door opener’s manual. Once the button is pressed, you have approximately 30 seconds to initiate the next step.
6. Press and hold the programed HomeLink button for two seconds and release. Repeat the sequence up to three times to complete the programing
process. HomeLink should now activate your rolling code equipped device.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Automatic Anti-Glare Rearview Mirror with HomeLink® Universal
Transceiver (if so equipped)
HomeLink

13
Fuel-filler Door
Passenger Rear Seat Entry/Exit
To access the rear seat:
1. Pull the lever
upward to
fold the seatback forward.
2. Press the button
to
slide the front seat forward
and press the button

again to stop the seat.
To return the front seat to its
original position:
1. Pull the lever
upward and push the seatback to the locked,
upright position.
2. Press the button
to slide the front seat backward.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
To open the fuel-filler door,
unlock the vehicle and gently
push the upper left side of
the fuel-filler door.
Please see your Owner’s Manual for
important safety information, system
limitations, and additional operating
and feature information.
To adjust the time and
the appearance of the
clock on the display:
1. Press the MENU
button
below
the lower display.
Then, touch the
“Settings” key on
the lower display.
2. Locate and touch
the “Clock” key to
adjust “On-Screen
Clock”, “Daylight
Savings Time”,
“Clock Format (24h)” and “Time Zone”.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
Clock Set/Adjustment