warning INFINITI QX30 2017 Owner's Guide

7. Check to make sure that the child restraint isproperly secured prior to each use. If the
seat belt is not locked, repeat steps 1
through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode (child
restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint in the rear seats using the LATCH
system: 1. Position the child restraint on the seat. Al-
ways follow the child restraint manufactur-
er’s instructions.
2. Secure the child restraint anchor attach-ments to the LATCH lower anchors. Check to
make sure the LATCH attachment is properly
attached to the lower anchors.
If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. For additional information, refer to
Installing top tether strap in the1. Safety
— seats, seat belts and supplemental re-
straint system section.
Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.
3. The back of the child restraint should be secured against the vehicle seatback.SSS0645ZForward-facing web-mounted — step 2
1-28Safety — seats, seat belts and supplemental restraint system

Installing top tether strap
The child restraint top tether strap must be
used when installing the child restraint with the
LATCH lower anchor attachments. First, secure
the child restraint with the LATCH lower anchors
(rear outboard seating positions only).
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no circum-
stances are they to be used to attach adult seat
belts, or other items or equipment to the ve-
hicle. Doing so could damage the child re-
straint anchorages. The child restraint will not
be properly installed using the damaged an-
chorage, and a child could be seriously injured
or killed in a collision.
Outboard seating positions with removable
head restraints/headrests
:
1. If necessary, raise or remove the head restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re- moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer to
Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack.
Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether strap, route the strap
1over the top of the outer
head restraint/headrest. If the child restraint
has two tether straps, route them round each
side of the outer head restraint/headrest.
2. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack.
NIC2849
1-30Safety — seats, seat belts and supplemental restraint system

If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
For additional information, refer toFront pas-
senger air bag and status light in the1. Safety
— seats, seat belts and supplemental restraint
system section.
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint. Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint using the vehicle seat belt in the
rear seats or in the front passenger seat:
1.If you must install a child restraint in the front
seat, it should be placed in a forward-facing
direction only. Move the seat to the rearmost
position. Child restraints for infants must be
used in the rear-facing direction and, there-
fore, must not be used in the front seat.
2. Position the child restraint on the seat. Always follow the child restraint manufactur-
er’s instructions. The back of the child re-
straint should be secured against the vehicle
seatback. If necessary, adjust or remove the
head restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is removed.
For additional information about head
restraint/headrest adjustment, removal and
WRS0699ZForward-facing (front passenger seat) — step 1
Safety — seats, seat belts and supplemental restraint system1-31

10. If the child restraint is installed in the frontpassenger seat, place the ignition switch in
the ON position. The front passenger air
bag status OFF light should illuminate. If
this light is not illuminated refer to Front
passenger air bag and status light in the
1. Safety — seats, seat belts and supple-
mental restraint system section.Move the
child restraint to another seating position.
Have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service. After the child restraint is removed
and the seat belt is fully retracted, the ALR
mode (child restraint mode) is canceled.
If the indicator
lamp does NOT light continuously when a
child restraint is installed on the front passenger seat, the seat may not be used
for a child restraint. Move the child re-
straint to another position. See
Troubleshooting
later in this section. Have
the system checked. It is recommended you
visit an INFINITI retailer for this service.
Installing top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no circum-
stances are they to be used to attach adult seat
belts, or other items or equipment to the ve-
hicle. Doing so could damage the child re-
straint anchorages. The child restraint will not
be properly installed using the damaged an-
chorage, and a child could be seriously injured
or killed in a collision.
The child restraint top tether strap must be
used when installing the child restraint with
seat belts.
First, secure the child restraint with the seat
belt. Outboard seating positions with removable
head restraints/headrests
:
1. If necessary raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re-
moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer to Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
SSS0676ZForward-facing — step 10NIC2848Rear seat - Type A
1-34Safety — seats, seat belts and supplemental restraint system

4. Tighten the tether strap according to themanufacturer’s instructions to remove any
slack.
Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether strap, route the strap
1over the top of the outer
head restraint/headrest. If the child restraint
has two tether straps, route them round each
side of the outer head restraint/headrest.
2. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack. Center seating position with adjustable head
restraint/headrest
:
1. Raise the head restraint/headrest. For addi-
tional information about head restraint/
headrest adjustment, removal and installa-
tion, refer to Head restraints/Headrests in
the 1. Safety — seats, seat belts and supple-
mental restraint system section.
2. Position the top tether strap
1under the
head restraint/head rest and over the seat-
back, between the two head restraint/
headrest stalks.
3. Secure the tether strap to the tether anchor point
2on the seatback behind the child
restraint.
4. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack.
If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
BOOSTER SEATS
For additional information on installing a
booster seat in your vehicle, follow the instruc-
tions outlined in this section.
Precautions on booster seats
WARNING
If a booster seat and seat belt are not used
properly, the risk of a child being injured or
killed in a sudden stop or collision greatly in-
creases:
•Make sure the shoulder portion of the belt is
away from the child’s face and neck and the
lap portion of the belt does not cross the
stomach.
•Make sure the shoulder belt is not behind
the child or under the child’s arm.
•A booster seat must only be installed in a
seating position that has a lap/shoulder
belt.
NIC2903Rear seat - Type B
Safety — seats, seat belts and supplemental restraint system1-35

Booster seats of various sizes are offered by
several manufacturers. When selecting any
booster seat, keep the following points in mind:
•Choose only a booster seat with a label
certifying that it complies with Federal Motor
Vehicle Safety Standard 213 or Canadian
Motor Vehicle Safety Standard 213.
•Check the booster seat in your vehicle to be
sure it is compatible with the vehicle’s seat
and seat belt system.
•Make sure the child’s head will be properly
supported by the booster seat or vehicle
seat. The seatback must be at or above the
center of the child’s ears. For example, if a
low back booster seat
1is chosen, the
vehicle seatback must be at or above the
center of the child’s ears. If the seatback is lower than the center of the child’s ears, a
high back booster seat
2should be used.
•If the booster seat is compatible with your
vehicle, place the child in the booster seat
and check the various adjustments to be
sure the booster seat is compatible with the
child. Always follow all recommended proce-
dures.
All U.S. states and Canadian provinces or territo-
ries require that infants and small children be
restrained in an approved child restraint at all
times while the vehicle is being operated.
The instructions in this section apply to booster
seat installation in the rear seats or the front
passenger seat.
Booster seat installation
WARNING
If a booster seat and seat belt are not used
properly, the risk of a child being injured or
killed in a sudden stop or collision greatly in-
creases:
•Make sure the shoulder portion of the belt is
away from the child’s face and neck and the
lap portion of the belt does not cross the
stomach.
•Make sure the shoulder belt is not behind
the child or under the child’s arm.
•A booster seat must only be installed in a
seating position that has a lap/shoulder
belt.
LRS0501ZLRS0464ZLRS0455Z
1-36Safety — seats, seat belts and supplemental restraint system

To avoid injury to a child, do not use the lap/
shoulder belt in the Automatic Locking Retrac-
tor (ALR) mode when using a booster seat with
the seat belts.
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section,Child restraints in
the 1. Safety — seats, seat belts and supple-
mental restraint system section andBooster
seats in the1. Safety — seats, seat belts and
supplemental restraint system section before
installing a child restraint.
Follow these steps to install a booster seat in
the rear seat or in the front passenger seat: 1.
If you must install a booster seat in the front
seat, move the seat to the rearmost position.
2. Position the booster seat on the seat. Only place it in a front-facing direction. Always
follow the booster seat manufacturer’s in-
structions. 3. The booster seat should be positioned on
the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint to obtain the correct booster seat
fit. If the head restraint is removed, store it
in a secure place. Be sure to reinstall the
head restraint when the booster seat is re-
moved.
For additional information about head
restraint/headrest adjustment, removal and
installation, refer to Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
If the seating position does not have an
adjustable head restraint/headrest and it is
interfering with the proper booster seat fit,
WRS0699ZLRS0451ZRear center position
Safety — seats, seat belts and supplemental restraint system1-37

try another seating position or a different
booster seat.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to
follow the booster seat manufacturer’s in-
structions for adjusting the seat belt routing.
5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack.
Be sure the shoulder belt is positioned
across the top, middle portion of the child’s
shoulder. Be sure to follow the booster seat
manufacturer’s instructions for adjusting the
seat belt routing.
6. Follow the warnings, cautions and instruc- tions for properly fastening a seat belt
shown in Precautions on seat belt usage
earlier in this section. 7. If the booster seat is installed in the front
passenger seat, place the ignition switch in
the ON position. Either the BAG ON>
1indicator light or GER AIR BAG OFF>
2indicator light
will illuminate depending on the size of the
child and the type of booster seat used. See
Front passenger air bag and status light in
the 1. Safety — seats, seat belts and supple-
mental restraint system section.
PRECAUTIONS ON SUPPLEMENTAL
RESTRAINT SYSTEM (SRS)
This Supplemental Restraint System (SRS) sec-
tion contains important information concerning
the following systems:
•Driver and passenger supplemental front im-
pact air bags (INFINITI Advanced Air Bag
System)
•Driver and passenger supplemental knee air
bags
•Front seat-mounted side-impact supplemen-
tal air bag
•Roof-mounted curtain side-impact supple-
mental air bags
•Seat belts with pretensioner
Supplemental front-impact air bag
system
The INFINITI Advanced Air Bag System can help
cushion the impact force to the head and chest
of the driver and front passenger in certain
frontal collisions.
LRS0452ZRear outboard positionNIC2740
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
1-38Safety — seats, seat belts and supplemental restraint system
** Click HERE to see "Owner's Manual Supplement" **

Driver’s and passenger’s
supplemental knee air bags
This system can help cushion the impact force
to the driver’s and passenger’s knees in certain
collisions.
Front seat-mounted side-impact
supplemental air bag system
This system can help cushion the impact force
to the chest and pelvis areas of the driver and
front passenger in certain side-impact colli-
sions. The side air bag is designed to inflate on
the side where the vehicle is impacted.
Window bag/roof-mounted curtain
side-impact and rollover
supplemental air bags
This system can help cushion the impact force
to the head of occupants in the outboard seat-
ing positions in certain side-impact or rollover
collisions. In a side impact, the curtain air bags
are designed to inflate on the side where the
vehicle is impacted. In a rollover, curtain air
bags on both sides are designed to inflate and
remain inflated for a short time.
Curtain air bags are also designed to inflate in
certain types of rollover collisions or near roll-
overs. As a result, certain vehicle movements(for example, during severe off-roading) may
cause the curtain air bags to inflate.
The SRS is designed to
supplementthe crash
protection provided by the driver and front
passenger seat belts and is not a substitute for
them. Seat belts should always be correctly
worn and the occupant seated a suitable dis-
tance away from the steering wheel, instrument
panel and front door finishers. For additional
information, see Seat beltsearlier in this
section.
The supplemental air bags operate only when
the ignition switch is placed in the ON position.
After placing the ignition switch in the ON, the
air bag warning light will illuminate. The air bag
warning light will turn off within a few seconds
after the engine is started if the system is opera-
tional. See Warning lights, indicator lights and
audible reminders in the2. Instruments and
controls section for further details.
Safety — seats, seat belts and supplemental restraint system1-39
** Click HERE to see "Owner's Manual Supplement" **

WARNING
•The front-air bags ordinarily will not inflate
in the event of a side impact, rear impact,
rollover, or lower severity frontal collision.
Always wear the seat belts to help reduce
the risk or severity of injury in accidents.
•The front passenger air bag will not inflate if
the passenger air bag status light is lit or if
the front passenger seat is unoccupied. For
additional information, refer toFront pas-
senger air bag and status light in the
1. Safety — seats, seat belts and supple-
mental restraint system section.
•The seat belts and the front-impact air bags
are most effective when you are sitting well
back and upright in the seat. The front air
bags inflate with great force. Even with the
INFINITI Advanced Air Bag System, if you are
unrestrained, leaning forward, sitting side-
ways, or out of position in any way, you are
at greater risk of injury or death in a crash.
You may also receive serious or fatal inju-
ries from the front air bag if you are up
against it when it inflates. Always sit back
against the seatback and as far away as
practical from the steering wheel. Always
properly use the seat belts.
WRS0031ZSit upright and well back
ARS1133ZSit upright and well back
1-40Safety — seats, seat belts and supplemental restraint system
** Click HERE to see "Owner's Manual Supplement" **