warning INFINITI QX30 2017 Workshop Manual

•The coolant is too hot and the engine is no
longer being cooled sufficiently.
Observe the additional display messages in the
vehicle information display.
Stop the vehicle immediately, paying attention
to road and traffic conditions, and switch off the
engine.
Secure the vehicle against rolling away.
Leave the vehicle and keep a safe distance from
the vehicle until the engine has cooled down.
Check the coolant level and top up the coolant,
observing the warning notes (see If your ve-
hicle overheats in the6. In case of emergency
section).
If you have to top up the coolant frequently,
have the engine cooling system checked.
Make sure that the air supply to the engine
radiator is not blocked, e. g. by frozen slush.
Do not start the engine again until the coolant
temperature is below 250
oF (120oC). The
engine may otherwise be damaged.
Low fuel warning light
This light comes on when the fuel level in the fuel
tank is getting low. Refuel as soon as it is conve-
nient, preferably before the fuel gauge reaches 0 (Empty).
There will be a small reserve of fuel in the
tank when the fuel gauge reaches 0 (Empty).
Vehicle Dynamic Control (VDC)
warning light
The VDC warning light blinks when the Vehicle
Dynamic Control (VDC) system is operating,
thus alerting the driver to the fact that the road
surface is slippery and the vehicle is nearing its
traction limits.
You may feel or hear the system working, this is
normal.
The light will continue to blink for a few seconds
after the VDC system stops limiting wheel spin.
Cruise control or Intelligent Cruise Control is
deactivated.
For additional information see Vehicle Dy-
namic Control (VDC) OFF indicator light in the
2. Instruments and controls section andVe-
hicle Dynamic Control (VDC) system in the
5. Starting and driving section.
INDICATOR LIGHTS
Turn signal/hazard indicator lights
The appropriate light flashes when the turn
signal switch is activated. Both lights flash
when the hazard switch is turned on.
Low beam indicator light
This light comes on when the switch is turned to
the position:The headlights will come on
and front side, tail, number plate and instru-
ment lights remain on.
Vehicle Dynamic Control (VDC)
OFF indicator light
The light comes on when the Vehicle Dynamic
Control (VDC) has been disabled. This indicates
that the VDC system is not operating.
Disabling the VDC system causes the Forward
Emergency Braking system to become unavail-
able. See Forward emergency braking (FEB)
system (if equipped) in the5. Starting and
driving section for more details.
This light also comes on briefly when the igni-
tion switch is turned to the ON position. The
light will turn off after approximately 1 second if
the VDC system is operational.
When the VDC OFF indicator light and VDC
warning light (see Vehicle Dynamic Control
(VDC) warning light later in this section) come
on with the VDC system turned on, it alerts the
driver to the fact that the system’s fail-safe
mode is operating. This means that the system
may not be functioning properly. Have the
Instruments and controls2-13

system checked. It is recommended you visit an
INFINITI retailer for these services.
If an abnormality occurs in the system, the VDC
system function will be canceled, but the ve-
hicle is still driveable. For additional informa-
tion, seeVehicle Dynamic Control (VDC)
system in the5. Starting and driving section.
WARNING
VDC should remain on unless freeing a vehicle
from mud or snow.
While the VDC system is operating, you might
feel a slight vibration or hear the system work-
ing when starting the vehicle or accelerating,
but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights are
switched on (see Fog light switch (If so
equipped) later in this section).
High beam assist indicator light
(if equipped)
The indicator light illuminates when the head-
lights come on while the headlight switch is in
the AUTO position with the high beam selected.
This indicates that the high beam assist system
is operational. (See 2-63.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the low
beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (see Fog light switch (If so
equipped) later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, see Headlight
and turn signal switches later in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light ()
located on the center console above the shift
lever will illuminate when the front passenger
air bag is turned OFF. When the front passenger
air bag is turned on, the front passenger air bag
status light ON (
) will illuminate.
For more details, see Front passenger air bag
and status light in the1. Safety — seats, seat
belts and supplemental restraint system sec-
tion.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver’s door
is opened if the side lights are on. Turn the
headlight control switch off before leaving the
vehicle.
2-14Instruments and controls

Seat belt reminder chime
A chime will sound for approximately 120 sec-
onds if the vehicle’s speed exceeds 16 MPH
(25 km/h) and the driver’s seat belt or front
passenger’s seat belt, if occupied is not se-
curely fastened. SeeSeat belt warning light in
the 1. Safety — seats, seat belts and supple-
mental restraint system section.
Idle Stop/Start System reminder
chime (if equipped)
The engine will shift to the normal stopped
state if any of the following operations is made
during Idle Stop/Start System activation, and
the Idle Stop/Start System chime will sound if:
– The vehicle engine hood is open.
When the above condition continues for over 3
minutes the Idle Stop/Start System chime will
sound in 5-minute intervals as a reminder to
prevent the possibility of a discharged battery.
Use the ignition switch to turn off the engine.
Close the hood or the driver’s door, or fasten
the seat belt then restart the engine using the
ignition switch.
For more information, see Idle Stop/Start
System (if equipped) in the5. Starting and
driving section. The vehicle information display1is located
between the tachometer and the speedometer.1Permanent display: depending on vehicle
specification: outside temperature or speed
2Time
3Text field
4Menu bar
5Drive program
6Shift lever position
Text field
3shows the selected menu or
submenu as well as display messages.
NOTE
Set the time using the INFINITI controller and the
[Settings] menu available in the central display
(see Clock settings in the4. Display screen,
heater and air conditioner, and audio system
section).
NIC2751NIC2752
VEHICLE INFORMATION DISPLAY
Instruments and controls2-15

Video DVD operation (outside Europe only):
It is only possible to use the [Audio] menu to
operate video DVDs on vehicles with navigation
system.
1. Switch on the audio system or navigationsystem and select video DVD.
2. Press the
orbutton on the
steering wheel to select the [Audio] menu.
3. To select the next or previous scene, briefly press
or.
4. To select a scene from the scene list (rapid scrolling): press and hold the
or. button until the desired scene1has
been reached.
Assistance menu
Depending on the equipment fitted in the ve-
hicle, you have the following options in the
[DriveAssist] menu:
•Showing the assistance graphic
•Activating/deactivating VDC
•Activating/deactivating Forward Emergency
Braking (FEB)
•Activating/deactivating Blind Spot Warning
(BSW)
•Activating/deactivating Lane Departure
Warning (LDW) Showing the distance display
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Distance display].
3. Press the button. The vehicle information display shows the
Intelligent Cruise Control (ICC) distance dis-
play in the assistance graphic.
The distance display also shows you the
status of and/or information from the follow-
ing driving systems or driving safety sys-
tems:
•Intelligent Cruise Control (ICC)
•Forward Emergency Braking (FEB)
NIC2726NIC2873NIC2729
2-22Instruments and controls

•Lane Departure Warning (LDW)
•Blind Spot Warning (BSW)
•Rear window wiper
Deactivating/activating VDC
:
The vehicle should be driven with the Vehicle
Dynamic Control (VDC) system on for most
driving conditions.
If the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce
wheel spin. The engine speed will be reduced
even if the accelerator is depressed to the floor.
If maximum engine power is needed to free a
stuck vehicle, turn the VDC system off.
For further information about VDC, see Vehicle
Dynamic Control (VDC) system in the
5. Starting and driving section.
1. Start the engine.
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu.
3. Press the
orbutton to select
[ESP]. 4. Press the button.
The current selection is displayed.
5. To activate/deactivate: press the button again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
If both the
warning light andwarning light are lit continuously, VDC is not
available due to a malfunction.
Activating/deactivating Forward Emergency
Braking
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Emergency Brake].
3. Press the button. The current selection is displayed.
4. To activate/deactivate: press the but- ton again.
When Forward Emergency Braking is deacti-
vated, the
symbol appears in the
vehicle information display in the assistance
graphic display. For further information about Forward Emer-
gency Braking, see
Forward emergency brak-
ing (FEB) system (if equipped) in the
5. Starting and driving section.
Activating/deactivating Blind Spot Warning
(BSW)
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Blind Spot Warning].
3. Press the button. The current selection is displayed.
4. To activate/deactivate: press the but- ton again.
For further information about Blind Spot Warn-
ing, see Blind Spot Warning (BSW) system (if
equipped) in the5. Starting and driving sec-
tion.
Activating/deactivating Lane Departure Warn-
ing (LDW)
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu on the Menu bar.
Instruments and controls2-23

2. Press theorbutton to select
[Lane Departure Warning].
3. Press the button on the steering wheel.
The current selection is displayed.
4. Press the to confirm.
5. Press the
orbutton to set [Off],
[Standard] or [Adaptive].
6. Press the button to save the setting.
For further information about Lane Departure
Warning, see Lane departure warning (LDW)
system (if equipped) in the 5. Starting and
driving section.
Service menu ([Serv.])
Depending on the equipment fitted in the ve-
hicle, you have the following options in the
[Serv.] menu:
•Calling up display messages in the message
memory (see Message memory later in this
section).
•Restarting the tire pressure monitoring sys-
tem (TPMS) (see Restarting TPMS in the5.
Starting and driving section.
•Checking the tire pressure electronically (see
Checking the tire pressure electronically in
the 5. Starting and driving section).
•Calling up the service due date (see Main-
tenance service messages in the
9. Maintenance and Schedules section).
Settings menu
Depending on the equipment fitted in the ve-
hicle, in the [Settings] menu you have the
following options:
•Changing the instrument cluster settings.
•Changing the light setting.
•Changing the vehicle setting.
•Changing the convenience setting.
•Restoring the factory setting.
Instrument cluster
:
Unit of measurement for distance: The Display
unit Speed-/odometer function allows you to
choose whether certain displays appear in kilo-
meters or miles in the vehicle information dis-
play.
NIC2874NIC2731
2-24Instruments and controls

5. Press the button to confirm the selec-tion.
If you have selected [Yes], the vehicle infor-
mation display shows a confirmation mes-
sage.
For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must
switch the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner’s Manual and may differ
from the symbols in the vehicle information
display.
Certain display messages are accompanied by
an audible warning tone or a continuous tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been rectified, these display messages are deleted
as well.
When you stop and park the vehicle, please
observe the notes on parking (see
Parkingin
the 5. Starting and driving section).
Hiding display messages
Press the orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for the
messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can call
up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service] menu.
If there are display messages, the vehicle
information display shows [2 messages], for
example. 2. Press the
orbutton to select the
entry, e.g. [2 messages].
3. Press to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

Safety systems
MessagePossible causes/consequences and solutions
[Currently Unavailable See
Operator’s Manual]ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily
unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
,andwarning lights may light up in the combination meter.
Possible causes:
•Self-diagnosis is not yet complete.•The on-board voltage may be insufficient.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you brake hard,
for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH (20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you visit an INFINITI
retailer for this service.
[Inoperative See Operator’s
Manual] ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to
a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
,,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The wheels could therefore lock if you brake hard,
for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
2-30Instruments and controls

MessagePossible causes/consequences and solutions
[Currently Unavailable See
Operator’s Manual]BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are temporarily unavailable.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
andwarning lights may light up in the combination meter.
The self-diagnosis function, for example, may not be complete.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Carefully drive on a suitable stretch of road, making slight steering movements, at a speed above 12 MPH(20 km/h). If the display
message disappears, the functions mentioned above are available again.
If the display message continues to be displayed, drive on carefully and have the system checked. It is recommended you an INFINITI
retailer for this service.
[Inoperative See Operator’s
Manual] BAS (Brake Assist System), VDC (Vehicle Dynamic Control), and hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
In addition, the
andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above.
The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked. It is recommended you visit an INFINITI retailer for this service.
Instruments and controls2-31

MessagePossible causes/consequences and solutions
[Inoperative See Operator’s
Manual]EBD (electronic brake force distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Contro), and
hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the
,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could therefore lock if
you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to Re-
lease the Parking Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
[Please Release Parking
Brake] The redindicator light flashes and a warning tone sounds. A condition for automatic release of the electric parking brake is not
fulfilled (see Applying automatically (vehicles with automatic transmission) in the5. Starting and driving section).
You are driving with the electric parking brake applied.
Release the electric parking brake manually.
The red
indicator light flashes and a warning tone sounds.
You are making an emergency stop using the electric parking brake (see Emergency brakingin the5. Starting and driving section)
[Parking Brake See Opera-
tor’s Manual] The yellowwarning light lights up.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off.
2. Press the electric parking brake handle for at least ten seconds.
3. Press the P (Park) button.
4. Have the system checked. It is recommended you consult an INFINITI retailer.
2-32Instruments and controls