lock INFINITI QX30 2017 Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2017, Model line: QX30, Model: INFINITI QX30 2017Pages: 556, PDF Size: 4.93 MB
Page 155 of 556
Press and hold thebutton until the side
windows are in the desired position.
To interrupt convenience opening: release the
button.
Convenience closing feature
WARNING
When the convenience closing feature is oper-
ating, parts of the body could become trapped
in the closing area of the side window. There is
a risk of injury. Observe the complete closing
procedure when the convenience closing fea-
ture is operating. When closing make sure that
no parts of the body are in the closing area.
For vehicles with Intelligent key: The key can
also be used to carry out the following functions
simultaneously:
•Lock the vehicle
•Close the side windows The driver’s door and the door at which the
handle is used must both be closed. The key
must be outside the vehicle. The gap between
the key and the corresponding door handle
should not be greater than 1 m.
Press and hold the
button until the side
windows are fully closed.
To interrupt convenience closing: release the
button.
You can also use the keyless locking feature to
activate convenience closing: Touch recessed sensor surface
1on the door
handle until the side windows are fully closed.
NOTE
Make sure you only touch recessed sensor sur-
face
1.
To interrupt convenience opening: release the
recessed sensor surface
1on the door handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON position.
2. Close the door.
3. Pull the corresponding switch on the door control panel until the side window is com-
pletely closed
NPA1478
2-74Instruments and controls
Page 157 of 556
Opening and closing
Manual control:
To close the sunshade, press and hold the
“CLOSE” side of the switch
1To stop the
sunshade from closing fully, release the switch.
To open the sunshade press and hold the
“OPEN” side of the switch
2To stop the
sunshade from opening fully, release the
switch.
Automatic operation
:
To fully open or close the sunshade automati-
cally, press briefly on the open or close side of
the switch and then release. To stop the sun-
shade from opening or closing, press either
side of the switch.
Auto-reverse function
:
When the control unit detects something caught
by the sunshade, the sunshade will open auto-
matically.
NOTE
The auto-reverse function remains active
whether the sunshade is being closed manually
or automatically. If the battery cable is disconnected, the clock
will need to be re-adjusted to the correct time.
ADJUSTING TIME
Set the time using the INFINITI controller and
the [Settings] menu available in the central
display (see
Clock settings in the4. Display
screen, heater and air conditioner, and audio
system section).
NOTE
On vehicles fitted with a navigation system, the
clock is automatically updated via GPS. The ini-
tial clock setting may be incorrect.
In the center console (LHD)
Rear console
NSD619NIC2690
NIC2683
CLOCK POWER OUTLET
2-76Instruments and controls
Page 159 of 556
GLOVE BOX
To open the glove box, pull the handle1.
To close, push the lid
2until the lock latches.
NOTE
To lock/unlock the glove box, use the mechani-
cal key. For the mechanical key usage, see Me-
chanical key in the3. Pre-driving checks and
adjustments section.
FRONT CONSOLE COMPARTMENT
To open the front console compartment, push
lid
1down and release. The lid will open.
To close, push the lid
1down until the lock
latches.
CONSOLE BOX
To open, pull up the lid from the front.
NIC2823NIC2663NIC2665
2-78Instruments and controls
Page 164 of 556
•Properly secure cargo and do not allow it to
contact the top tether strap when it is at-
tached to the top tether anchor. Cargo that
is not properly secured or cargo that con-
tacts the top tether strap may damage the
top tether strap during a collision. If the
cargo cover contacts the top tether strap
when it is attached to the top tether anchor,
remove the cargo cover from the vehicle or
secure it on the cargo floor below its attach-
ment location. If the cargo cover is not re-
moved, it may damage the top tether strap
during a collision. Your child could be seri-
ously injured or killed in a collision if the
child restraint top tether strap is damaged.
•Do not use the cargo cover if the rear seats
are folded down.
Removal
1. Open the lift gate (seeLift gate lockin the
2. Instruments and controls section).
2. Detach both of the cords (left and right)
1from the inside of the lift gate.
3. Detach the parcel shelf
2by simply pulling
it rearwards through the lift gate opening.
CAUTION
Make sure the parcel shelf is carefully stored
when not in use in order to prevent any
damage.
Installation
1. Open the lift gate.
2. Insert the parcel shelf by pushing it forwards as far as possible through the lift gate
opening.
3. Attach the corresponding cords to each side
1of the lift gate.
4. Close the lift gate (see Lift gate lockin the
2. Instruments and controls section).
ROOF RACK (IF EQUIPPED)
Genuine NISSAN accessory cross bars are avail-
able through an INFINITI retailer. It is recom-
mended you visit an INFINITI retailer for cross-
bar or other equipment information.
Always distribute the luggage evenly on the roof
rack. Observe the maximum load limit shown on
the crossbars or roof carriers when you attach
them on the roof rails. It is recommended you
visit an INFINITI retailer for cross bar or other
equipment information.
Do not apply any load directly to the roof side
rails. Cross bars (if so equipped) must be
installed before applying load/cargo/luggage
to the roof of the vehicle.
Be careful that your vehicle does not exceed the
Gross Vehicle Weight Rating (GVWR) or its Gross
Axle Weight Rating (GAWR front and rear). The
GVWR and GAWR are located on the F.M.V.S.S.
or C.V. M.S.S. certification label (located on the
driver’s door pillar). For additional information,
refer toVehicle loading information in the10.
Technical information section.
NIC2672
Instruments and controls2-83
Page 165 of 556
WARNING
•Drive extra carefully when the vehicle is
loaded at or near the cargo carrying capac-
ity, especially if the significant portion of
that load is carried on the roof rack.
•Heavy loading of the roof rack has the po-
tential to affect the vehicle stability and
handling during sudden or unusual han-
dling maneuvers.
•Roof rack load should be evenly distributed.
•Do not exceed maximum roof rack load
weight capacity.
•Properly secure all cargo with ropes or
straps to help prevent it from sliding or
shifting. In a sudden stop or collision, unse-
cured cargo could cause personal injury.
CAUTION
Always install the cross bars (if so equipped)
onto the roof side rails before loading cargo of
any kind. Loading cargo directly onto the roof
side rails or the vehicle’s roof may cause ve-
hicle damage.
SKI HATCH (IF EQUIPPED)
To open the ski hatch:
1. Fold down rear seat armrest.
2. Pull the center head restraint on the rearbench seat into the uppermost position.
3. Slide locking mechanism
1in the direction
of the arrow
4. Swing flap
2fully to the side. The flap is
held open by a magnet.
To close the ski hatch:
1. Swing flap
1in the luggage compartment
back until it engages.
2. Fold armrest fully up if necessary.
COMPARTMENT UNDER TRUNK FLOOR
Lift the trunk floor to access the underfloor
storage area.
NIC2668NIC2673
2-84Instruments and controls
Page 166 of 556
CAUTION
•Turn off the lights when you leave the ve-
hicle.
•Do not use the lights for extended periods of
time with the engine stopped. This could
result in a discharged battery.
FRONT OVERHEAD CONTROL PANEL
1Switches the left-hand front reading lamp
on/off
2Switches the front interior lighting on
3Switches the rear interior lighting on/off
4Switches the right-hand front reading
lamp on/off
5Switches the front interior lighting/
automatic interior lighting control off
6Switches the automatic interior lighting
control on
Automatic interior lighting control
•To switch on: set the switch to center posi-
tion
6.
•To switch off: press switch5.
The interior lighting automatically switches on if
you:
•Unlock the vehicle
•Open a door
•Remove the key from the ignition lock.
The interior lighting is activated for a short time
when the key is removed from the ignition lock.
You can activate this delayed switch-off using
the vehicle information display (see Activating/
deactivating the interior lighting delay earlier
in this section).
NIC2630
INTERIOR LIGHTS
Instruments and controls2-85
Page 167 of 556
REAR READING LIGHTS (IF EQUIPPED)
1Switches the left hand reading light on/
off
2Switches the right hand reading light
on/off
REAR ROOM LIGHT (IF EQUIPPED)
The rear room light (without switches) can be
switched on and off using the front overhead
control panel.
VANITY MIRROR LIGHTS
To access the vanity mirror, pull the sun visor
down and flip open the mirror cover.
The vanity mirror light illuminates when the
vanity mirror cover is opened. When the cover is
closed, the light will turn off.
LUGGAGE COMPARTMENT LIGHT
The light illuminates while the lift gate is
opened. When the lift gate is closed, the light
will turn off.
BATTERY SAVER SYSTEM
When the interior light stays on, it will auto-
matically turn off within a period of time after
the ignition switch has been turned to the OFF
position. To turn on the light again, put the
ignition switch in the ON position.The HomeLink® Universal Transceiver, inte-
grated in the vehicle’s inside rear view mirror,
provides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
HomeLink® Universal Transceiver:
•Will operate most Radio Frequency (RF) de-
vices such as garage doors, gates, home and
office lighting, entry door locks and security
systems.
•Is powered by your vehicle’s battery. No
separate batteries are required. If the vehi-
cle’s battery is discharged or is discon-
nected, HomeLink® will retain all program-
ming.
When the HomeLink® Universal Transceiver is
programmed, retain the original transmitter for
future programming procedures (Example: new
vehicle purchases). Upon sale of the vehicle, the
programmed HomeLink® Universal Transceiver
buttons should be erased for security purposes.
For additional information, refer to Program-
ming HomeLink® later in this section.
NIC2632SIC3869Z
HOMELINK® UNIVERSAL TRANSCEIVER (IF
EQUIPPED)
2-86Instruments and controls
Page 172 of 556
3 Pre-driving checks and adjustments
Keys.............................. .3-2
INFINITI Intelligent key ..................3-2
INFINITI Vehicle immobilizer system keys .......3-3
Doors ............................. .3-4
Locking with the key .................. .3-4
Locking with the mechanical key ............3-5
Locking with inside door knob .............3-6
Locking with Power door lock switch .........3-6
Automatic door locks .................. .3-6
Child safety rear door lock ...............3-7
Lift gate lock ....................... .3-7
INFINITI intelligent key system ...............3-7
Operating range ..................... .3-9
Door locks/unlocks precaution ............3-10
INFINITI intelligent key operation ...........3-10Changing the settings of the locking system . . . .3-11
Troubleshooting guide
.................3-12
Hood ............................. .3-14
Fuel-filler door ....................... .3-15
Opening fuel-filler door .................3-15
Fuel-filler cap ...................... .3-15
Steering wheel ....................... .3-16
Sun visors .......................... .3-17
Vanity mirror ...................... .3-17
Mirrors ............................ .3-17
Automatic anti-glare rear view mirror .........3-17
Outside mirrors ..................... .3-17
Memory function (if equipped) ..............3-20
Storing settings .................... .3-21
Calling up a stored setting ...............3-21
Page 173 of 556
INFINITI INTELLIGENT KEY
Your vehicle can only be driven with the Intelli-
gent Keys which are registered to your vehicle’s
Intelligent Key System components and INFINITI
Vehicle Immobilizer System components.
Never leave the keys in the vehicle.
As many as four Intelligent Keys can be regis-
tered and used with one vehicle. The new keys
must be registered prior to use with the Intelli-
gent Key System and INFINITI Vehicle Immobi-
lizer System of your vehicle. It is recommended
that you visit an INFINITI retailer for this service.
Since the registration process requires erasing
all memory in the Intelligent Key components
when registering new keys, be sure to take all
Intelligent Keys that you have to the INFINITI
retailer.A key number plate is supplied with your keys.
Record the key number and keep it in a safe
place (such as your wallet), not in the vehicle. If
you lose your keys, it is recommended that you
visit an INFINITI retailer for duplicates by using
the key number. INFINITI does not record key
numbers so it is very important to keep track of
your key number plate.
A key number is only necessary when you have
lost all keys and do not have one to duplicate
from. If you still have a key, it can be duplicated
without knowing the key number.CAUTION
Listed below are conditions or occurrences
which will damage the Intelligent Key:
•Do not allow the Intelligent Key, which con-
tains electrical components, to come into
contact with water or salt water. This could
affect the system function.
•Do not drop the Intelligent Key.
•Do not strike the Intelligent Key sharply
against another object.
•Do not change or modify the Intelligent Key.
•Wetting may damage the Intelligent Key. If
the Intelligent Key gets wet, immediately
wipe until it is completely dry.
•Do not place the Intelligent Key for an ex-
tended period in an area where tempera-
tures exceed 140
oF (60oC).
•Do not attach the Intelligent Key with a key
holder that contains a magnet.
•Do not place the Intelligent Key near equip-
ment that produces a magnetic field, such
as a TV, audio equipment and personal
computers.
If an Intelligent Key is lost or stolen, INFINITI
recommends erasing the ID code of that Intelli-
gent Key. This will prevent the Intelligent Key
from unauthorized use to unlock the vehicle. For
information regarding the erasing procedure,
please contact an INFINITI retailer.
Mechanical key
CAUTION
Always carry the mechanical key installed in
the Intelligent Key.
NPA1497
KEYS
3-2Pre-driving checks and adjustments
Page 174 of 556
Push release catch1in the direction of the
arrow and, at the same time, remove emergency
key element
2from the key.
Valet hand-off
To prevent the glove box from being opened
during valet hand-off, follow the procedure be-
low.
1. Remove the mechanical key from the Intelli- gent Key.
2. Lock the glove box with the mechanical key.
3. Hand the Intelligent Key to the valet and keep the mechanical key with you.
For additional information, refer to Storagein
the 2. Instruments and controls section.
INFINITI VEHICLE IMMOBILIZER
SYSTEM KEYS
You can only drive your vehicle using the Intel-
ligent Keys which are registered to the INFINITI
Vehicle Immobilizer System components in your
vehicle.
The mechanical key can be used for all the
locks.
Never leave the keys in the vehicle.
Additional or replacement keys:
If you still have a key, the key number is not
necessary when you need extra INFINITI Vehicle
Immobilizer System keys. Your existing key can
be duplicated without knowing the key number.
As many as four INFINITI Vehicle Immobilizer
System keys can be used with one vehicle. You
should bring all INFINITI Vehicle Immobilizer
System keys that you have to the INFINITI
retailer for registration. This is because the
registration process will erase the memory of all
key codes previously registered into the INFINITI
Vehicle Immobilizer System. After the registra-
tion process, these components will only recog-
nize keys coded into the INFINITI Vehicle Immo-
bilizer System during registration. Any key that
is not given to the retailer at the time of
registration will no longer be able to start your
vehicle.
CAUTION
Do not allow the immobilizer system key,
which contains an electrical transponder, to
come into contact with water or salt water. This
could affect system function.
NPA1494
Pre-driving checks and adjustments3-3