lock INFINITI QX30 2017 Owner's Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2017, Model line: QX30, Model: INFINITI QX30 2017Pages: 556, PDF Size: 4.93 MB
Page 116 of 556
MessagePossible causes/consequences and solutions
[Parking Brake Inoperative]The yellowwarning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake has been
applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning, e.g. because of overvoltage or undervoltage.
1. Rectify the cause of the overvoltage or undervoltage, e.g. by charging the battery or restarting the engine.
2. Apply or release the electric parking brake.
If the electric parking brake still cannot be applied or released:
1. Switch the ignition off and turn it back on.
2. Apply or release the electric parking brake manually.
If the electric parking brake still cannot be applied or released, it is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes.
It is not possible to apply the electric parking brake manually.
1. Press the P (Park) button.
Consult an INFINITI retailer.
[Brake Immediately] A tone may also sound at regular intervals. If you attempt to lock the vehicle, the tone becomes louder.
You cannot start the engine.
1. Paying attention to the traffic situation, immediately depress the brake pedal firmly and hold until the display message disappears.
2. Secure the vehicle against rolling away. You can restart the engine.
Instruments and controls2-35
Page 125 of 556
MessagePossible causes/consequences and solutions
[Coolant Too Hot Stop Vehicle
Turn Engine Off] The coolant is too hot.
A warning tone also sounds.
CAUTIONIf the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the
gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle
may seriously damage the engine. For additional information, refer to
If your vehicle overheatsin the6. In case of emergency section
for immediate action required.
1. Stop the vehicle immediately, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Wait until the engine has cooled down.
4. Make sure that the air supply to the engine radiator is not blocked, e.g. by frozen slush.
5. Do not start the engine again until the display message goes out and the coolant temperature is below 120
oC. The engine may
otherwise be damaged.
6. Pay attention to the coolant temperature display.
7. If the temperature increases again, have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 250
oF (120oC).
See If your vehicle overheats in the6. In case of emergency section.
[See Operator’s Manual] The battery is not being charged.
A warning tone also sounds.
Possible causes:
•Faulty alternator.•Torn poly-V-belt.•A malfunction in the electronics.
CAUTIONDo not continue driving. The engine could otherwise overheat.
1. Stop the vehicle immediately, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Have the system checked. It is recommended you visit an INFINITI retailer for this service.
2-44Instruments and controls
Page 134 of 556
Vehicle
MessagePossible causes/consequences and solutions
[Depress Brake to Start
Engine] (DCT models only). You have attempted to start the engine with the transmission in position N (Neutral) without depressing the brake
pedal.
Depress the brake pedal.
[To Deselect P or N, Depress
Brake and Start Engine] You have attempted to shift the shift lever to position R (Reverse) or D (Drive) without starting the engine.
Start the engine and depress the brake pedal.
NOTE•It is only possible to move the shift lever from position P (Park) to the desired position if you depress the brake pedal. Only then can
the parking lock be deactivated.
•At transmission fluid temperatures below -5oF (-20oC) you can only shift out of position P (Park) into another transmission position
when the engine is running.
[Apply Brake to Shift From ’P’] You have attempted to shift the shift lever to position R (Reverse), N (Neutral) or D (Drive) without depressing the brake pedal. Depress the brake pedal.
[Risk of Rolling Transmission
Not in P] The driver’s door is open/not fully closed and the shift lever is in position R (Reverse), N (Neutral) or D (Drive).
A warning tone also sounds
WARNING
The vehicle may roll away.
There is a risk of an accident.
1. Press the P (Park) button.
2. Secure the vehicle against rolling away.
3. Close the driver’s door fully.
[Service Required Do Not Shift
Gears Visit Dealer] You cannot change the transmission position due to a malfunction.
A warning tone also sounds.
If transmission position D (Drive) is selected, Drive to an INFINITI retailer without shifting the transmission from position D (Drive).
If transmission position R (Reverse), N (Neutral) or P (Park), secure the vehicle against rolling away. It is recommended you consult an
INFINITI retailer.
Instruments and controls2-53
Page 136 of 556
MessagePossible causes/consequences and solutions
The lift gate is open.
WARNING
When the engine is running, exhaust gases can enter the vehicle interior if the lift gate is open.
There is a risk of poisoning
Close the lift gate.
The hood is open.
A warning tone also sounds.
WARNING
The open hood may then block your view when the vehicle is in motion.
There is a risk of an accident.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Close the hood.
At least one door is open. A warning tone also sounds.
Close all doors.
[Power Steering Malfunction
See Operator’s Manual]The power steering assistance is faulty.
A warning tone also sounds.
WARNING
You will need to use more force to steer.
There is a risk of an accident.
1. Check whether you are able to apply the extra force required.
2. If you are able to steer safely: carefully drive on to a qualified specialist workshop.
3. If you are unable to steer safely: do not drive on. It is recommended you contact the nearest INFINITI retailer.
Instruments and controls2-55
Page 137 of 556
MessagePossible causes/consequences and solutions
[Steering Malfunction See
Operator’s Manual]The electric steering lock is malfunctioning.WARNING
The steering may be locked by the electric steering lock.
There is a risk of an accident.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Do not drive on. It is recommended you contact the nearest INFINITI retailer.
The electric steering lock was unable to unlock the steering.
1. Remove the key from the ignition switch.
2. To unlock the steering, move the steering wheel slightly.
3. Insert the key into the ignition lock again.
[Check Washer Fluid]
The washer fluid level in the washer fluid reservoir has dropped below the minimum.
Top up the washer fluid (see
Window washer fluidin the8. Do-it-yourself section)
[Wiper Malfunctioning] The windshield wipers are defective. Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Hazard Warning Flashers
Malfunctioning] The hazard warning lights are faulty.
Visit an INFINITI retailer.
2-56Instruments and controls
Page 139 of 556
IMMOBILISER
The immobiliser prevents your vehicle from
being started without the correct key.
•To activate with the key: remove the key from
the ignition lock.
•To deactivate:switch on the ignition.
When leaving the vehicle, always take the key
with you and lock the vehicle. Anyone can start
the engine if a valid key has been left inside the
vehicle.
NOTE
The immobiliser is always deactivated when you
start the engine.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ANTI-THEFT ALARM SYSTEM (IF
EQUIPPED)
To arm:
lock the vehicle with the key or Intelli-
gent key. Indicator lamp
1flashes. The alarm
system is armed after approximately 15 sec-
onds.
To deactivate: unlock the vehicle with the key or
intelligent key.
or
Insert the key into the ignition switch.
A visual and audible alarm is triggered if the
alarm system is armed and you open:
•A door.
•The vehicle with the emergency key element.
NIC2750
SECURITY SYSTEM
2-58Instruments and controls
Page 149 of 556
–Who have low intensity lighting, e. g.
cyclists.
– Whose lighting is blocked, e.g. by a bar-
rier.
•In very rare cases, High beam Assist recog-
nizes road users too late or not at all. In this,
or in similar situations, the automatic high
beam headlights will not be deactivated or
activated regardless. There is a risk of an
accident.
•Always carefully observe the traffic condi-
tions and switch off the high beam head-
lights in good time.
CAUTION
High beam Assist cannot compensate for road
and weather circumstances while driving. The
system saves the driver from having to operate
the switch. The driver always remains respon-
sible for choosing the correct light setting.
Specific situations in which to operate the
headlight switch manually:
•In heavy rain, snowy conditions. (general
poor visibility and bad weather conditions).
•When the vehicle sensors are dirty, covered
or broken.
Switching High Beam Assist on/off
To switch on:
Turn the light switch to
combination switch beyond the pressure point
in the direction of arrow
3. Theindicator
light in the vehicle information display lights up
when it is dark and the light sensor switches on
the low-beam headlights.
If you are driving at speeds above approxi-
mately 28 MPH (45 km/h) the headlight range is
set automatically depending on the distance
between the vehicle and other road users.
If you are driving at speeds above approxi-
mately 34 MPH (55 km/h) and no other road
users are detected, the high beam headlights
are switched on automatically. The
indi- cator light in the combination meter also lights
up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road users
are detected or the roads are adequately lit The
high beam headlights are switched off auto-
matically. The
indicator light in the com-
bination meter goes out. Theindicator
light in the vehicle information display remains
lit.
To deactivate
:
Move the combination switch back to its normal
position Theindicator light in the vehicle
information display goes out.
HEADLIGHTS MISTED UP ON THE
INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of the
headlight.
NIC2618
2-68Instruments and controls
Page 150 of 556
INSTRUMENT BRIGHTNESS CONTROL
The light sensor in the combination meter au-
tomatically controls the brightness of the in-
strument panel
In daylight, the displays in the combination
meter are not illuminated
The lighting in the combination meter, displays
and controls in the vehicle interior can be
adjusted using the brightness control knob.
The brightness control knob
1is located be-
hind the steering wheel.
Turn the brightness control knob clockwise or
counterclockwise. If the light switch is set to
orthe brightness is dependent
upon the brightness of the ambient light.
FRONT FOG LIGHTS
In conditions where visibility is poor due to fog,
snow or rain, the fog lights improve visibility as
well as making it easier for other road users to
see you. They can be operated together with the
side lights or together with the side lights and
low beam headlights.
To switch on the fog lights:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor
•Press thebutton. The greenindicator light in the combination meter
lights up To switch off the front fog lights:
•press thebutton The greenindica-
tor light in the combination meter turns off.
Only vehicles with front fog lights are equipped
with the “Fog lights” function.
REAR FOG LIGHT
The rear fog light improves the visibility of your
vehicle in heavy fog for the following traffic.
Please observe the country-specific laws on the
use of rear fog lights.
NOTE
The front fog lights must be switched on before
the rear fog light will operate.
To switch on the rear fog light:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor
•Press thebutton. The yellowindicator light in the combination meter
lights up
To switch off the rear fog light:
•press thebutton The yellowindicator light in the combination meter
turns off.
NIC2615NIC2699
FOG LIGHT SWITCH (IF SO EQUIPPED)
Instruments and controls2-69
Page 153 of 556
POWER WINDOWS
WARNING
•Make sure that all passengers have their
hands, etc. inside the vehicle while it is in
motion and before closing the windows. Use
the window lock switch to prevent unex-
pected use of the power windows.
•To help avoid risk of injury or death through
unintended operation of the vehicle and or
its systems, including entrapment in win-
dows or inadvertent door lock activation, do
not leave children, people who require the
assistance of others or pets unattended in
your vehicle. Additionally, the temperature
inside a closed vehicle on a warm day can
quickly become high enough to cause a sig-
nificant risk of injury or death to people and
pets.
The switches for all side windows are located on
the driver’s door. There is also a switch on each
door for the corresponding side window The
switches on the driver’s door take precedence.
Auto-reverse function
The auto-reverse function can be activated
when a window is closed by automatic opera-
tion. Depending on the environment or driving condi-
tions, the auto-reverse function may be acti-
vated if an impact or load similar to something
being caught in the window occurs.
WARNING
There are some small distances immediately
before the closed position which cannot be
detected. Make sure that all passengers have
their hands, etc., inside the vehicle before
closing the window.
If the vehicle’s battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate properly.
If this occurs, it is recommended you visit an
INFINITI retailer to re-initialize the power win-
dow auto-reverse system.
If the control unit detects something caught in a
window equipped with automatic operation as
it is closing, the window will be immediately
lowered.
Driver’s window switch
The power windows operate when the ignition
switch is in the ON position. 1. Front left side window
2. Front right side window
3. Rear left side window
4. Rear right side window
The driver’s switch, the main switch, can control
all windows.
•To open manually: press and hold the corre-
sponding button.
•To open fully: press the button beyond the
point of resistance to the second detent and
release it. Automatic operation is started.
•To close manually: pull the corresponding
button and hold it.
•To close fully: pull the button beyond the
point of resistance and release it. Automatic
operation is started.
NIC2715
WINDOWS
2-72Instruments and controls
Page 154 of 556
•To interrupt automatic operation: press/pull
the corresponding switch again.
NOTE
•If you press/pull the switch beyond the point
of resistance, automatic operation is started
in the corresponding direction. You can stop
automatic operation by pressing/pulling
again.
•You can continue to operate the side win-
dows after switching off the engine or remov-
ing the key. This function remains active for
five minutes or until the driver’s or front-
passenger door is opened.
•The side windows cannot be operated from
the rear when the override feature for the
side windows is activated. Locking rear side windows
:
To enable/disable the override feature for the
rear side windows, press button
2. If indicator
lamp
1is lit, operation of the rear side win-
dows is disabled. Operation is only possible
using the switches in the driver’s door. If indi-
cator lamp
1is off, operation is possible using
the switches in the rear compartment.
Passenger’s window switch
The passenger’s switch can control its corre-
sponding window.
Convenience opening feature
For vehicles with Intelligent key: you can venti-
late the vehicle before you start driving. The key
can also be used to carry out the following
functions simultaneously:
•Unlock the vehicle
•Open the side windows
NOTE
The convenience opening feature can only be
operated using the key.
The key must be in close proximity to the ve-
hicle.
NIC2716NIC2640
Instruments and controls2-73