lock INFINITI QX30 2017 User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2017, Model line: QX30, Model: INFINITI QX30 2017Pages: 556, PDF Size: 4.93 MB
Page 38 of 556
•The retractor is designed to lock during a
sudden stop or on impact. A slow pulling
motion permits the belt to move and al-
lows you some freedom of movement in
the seat.
•If the seat belt cannot be pulled from its
fully retracted position, firmly pull the belt
and release it. Then smoothly pull the belt
out of the retractor.
3. Position the lap belt portion low and snug on
the hips as shown 4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two
modes of operation:
•Emergency Locking Retractor (ELR)
•Automatic Locking Retractor (ALR)
The ELR mode allows the seat belt to extend and
retract to allow the driver and passengers some
freedom of movement in the seat. The ELR locks
the seat belt when the vehicle slows down
rapidly or during certain impacts.
The ALR mode (child restraint mode) locks the
seat belt for child restraint installation. When
the ALR mode is activated, the seat belt cannot be extended again until the seat belt tongue is
detached from the buckle and fully retracted.
The seat belt returns to the ELR mode after the
seat belt fully retracts. For additional informa-
tion, refer to
Child restraints later in this
section. The ALR mode should be used only for
child restraint installation. During normal seat
belt use by an occupant, the ALR mode should
not be activated. If it is activated, it may cause
uncomfortable seat belt tension. It can also
change the operation of the front passenger air
bag. For additional information, refer to Front
passenger air bag and status light in the
1. Safety — seats, seat belts and supplemental
restraint system section.
WARNING
When fastening the seat belts, be certain that
the seatbacks are completely secured in the
latched position. If they are not completely
secured, passengers may be injured in an acci-
dent or sudden stop.
SSS0292ZSSS0290Z
Safety — seats, seat belts and supplemental restraint system1-15
Page 39 of 556
Unfastening the seat belts
To unfasten the seat belt, push the button on
the buckle and guide the seat belt as it auto-
matically retracts.
Checking seat belt operation
Seat belt retractors are designed to lock seat
belt movement by two separate methods:
•When the belt is pulled quickly from the
retractor.
•When the vehicle slows down rapidly.
To increase your confidence in the seat belts,
check the operation as follows:
•Grasp the shoulder belt and pull forward
quickly. The retractor should lock and restrict
further belt movement.
If the retractor does not lock during this check,
get the system checked. It is recommended that
you visit an INFINITI retailer for this service, or
to learn more about seat belt operation.Shoulder belt height adjustment (if
equipped)
The shoulder belt anchor height should be
adjusted to the position that is best for you.
(See Fastening the seat belts earlier in this
section).
•To adjust, push the button and then move
the shoulder belt anchor to the desired po-
sition so that the belt passes over the center
of the shoulder. The belt should be away
from your face and neck, but not falling off of
your shoulder. Release the adjustment but-
ton to lock the shoulder belt anchor into
position.
SSS0326ZSSS0896Z
1-16Safety — seats, seat belts and supplemental restraint system
Page 41 of 556
WARNING
Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR) mode
seat belts. If the seat belt becomes wrapped
around a child’s neck with the ALR mode acti-
vated, the child can be seriously injured or
killed if the seat belt retracts and becomes
tight. This can occur even if the vehicle is
parked. Unbuckle the seat belt to release the
child. If the seat belt can not be unbuckled or is
already unbuckled, release the child by cutting
the seat belt with a suitable tool (such as a
knife or scissors) to release the seat belt.
Children need adults to help protect them.
They need to be properly restrained.
In addition to the general information in this
manual, child safety information is available
from many other sources, including doctors,
teachers, government traffic safety offices, and
community organizations. Every child is differ-
ent, so be sure to learn the best way to trans-
port your child.
There are three basic types of child restraint
systems:
•Rear-facing child restraint
•Forward-facing child restraint
•Booster seat
The proper restraint depends on the child’s
size. Generally, infants up to about 1 year and
less than 20 lb (9 kg) should be placed in
rear-facing child restraints. Forward-facing child
restraints are available for children who out-
grow rear-facing child restraints and are at least
1 year old. Booster seats are used to help
position a vehicle lap/ shoulder belt on a child
who can no longer use a forward-facing child
restraint.
WARNING
Infants and children need special protection.
The vehicle’s seat belts may not fit them prop-
erly. The shoulder belt may come too close to
the face or neck. The lap belt may not fit over
their small hip bones. In an accident, an im-
properly fitting seat belt could cause serious or
fatal injury. Always use appropriate child
restraints.
All U.S. states and Canadian provinces or terri-
tories require the use of approved child re-
straints for infants and small children. See
Child restraints in the1. Safety — seats, seat
belts and supplemental restraint system sec-
tion for more information. A child restraint may be secured in the vehicle
by using either the LATCH (Lower Anchor and
Tethers for CHildren) system or with the vehicle
seat belt. For additional information, refer to
Child restraints
in the1. Safety — seats, seat
belts and supplemental restraint system sec-
tion.
INFINITI recommends that all pre-teens and chil-
dren be restrained in the rear seat. Studies show
that children are safer when properly restrained
in the rear seat than in the front seat.
This is especially important because your ve-
hicle has a supplemental restraint system (air
bag system) for the front passenger. (See
Supplemental Restraint System (SRS) later in
this section.)
INFANTS
Infants up to at least 1 year old should be
placed in a rear-facing child restraint. INFINITI
recommends that infants be placed in child
restraints that comply with Federal Motor Ve-
hicle Safety Standards or Canadian Motor Ve-
hicle Safety Standards. You should choose a
child restraint which fits your vehicle and al-
ways follow the manufacturer’s instructions for
installation and use.
CHILD SAFETY
1-18Safety — seats, seat belts and supplemental restraint system
Page 48 of 556
4. After attaching the child restraint, test itbefore you place the child in it. Push it from
side to side while holding the child restraint
near the LATCH attachment path. The child
restraint should not move more than 1 inch
(25 mm), from side to side. Try to tug it
forward and check to see if the LATCH
attachment holds the restraint in place. If
the restraint is not secure, tighten the LATCH
attachment as necessary, or put the re-
straint in another seat and test it again. You
may need to try a different child restraint or
try installing by using the vehicle seat belt (if
applicable). Not all child restraints fit in all
types of vehicles. 5. Check to make sure the child restraint is
properly secured prior to each use. If the
child restraint is loose, repeat steps 2
through 4.
REAR-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision.
Rear-facing child restraints must not be used
on the front seats. For additional information, refer to all Warnings
and Cautions in the
Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a rear-facing child
restraint using the vehicle seat belts in the rear
seats:
LRS0673ZRear-facing — step 3LRS0674ZRear-facing — step 4
Safety — seats, seat belts and supplemental restraint system1-25
Page 51 of 556
7. Check to make sure that the child restraint isproperly secured prior to each use. If the
seat belt is not locked, repeat steps 1
through 6.
After the child restraint is removed and the
seat belt fully retracted, the ALR mode (child
restraint mode) is canceled.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING LATCH
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint.
Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint in the rear seats using the LATCH
system: 1. Position the child restraint on the seat. Al-
ways follow the child restraint manufactur-
er’s instructions.
2. Secure the child restraint anchor attach-ments to the LATCH lower anchors. Check to
make sure the LATCH attachment is properly
attached to the lower anchors.
If the child restraint is equipped with a top
tether strap, route the top tether strap and
secure the tether strap to the tether anchor
point. For additional information, refer to
Installing top tether strap in the1. Safety
— seats, seat belts and supplemental re-
straint system section.
Do not install child restraints that require
the use of a top tether strap in seating
positions that do not have a top tether
anchor.
3. The back of the child restraint should be secured against the vehicle seatback.SSS0645ZForward-facing web-mounted — step 2
1-28Safety — seats, seat belts and supplemental restraint system
Page 54 of 556
If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
For additional information, refer toFront pas-
senger air bag and status light in the1. Safety
— seats, seat belts and supplemental restraint
system section.
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section andChild restraints
in the 1. Safety — seats, seat belts and supple-
mental restraint system section before install-
ing a child restraint. Do not use the lower anchors if the combined
weight of the child and the child restraint
exceeds 65 lb (29.5 kg). If the combined weight
of the child and the child restraint is greater
than 65 lb (29.5 kg), use the vehicle seat belt
(not the lower anchors) to install the child
restraint. Be sure to follow the child restraint
manufacturer’s instructions for installation.
Follow these steps to install a forward-facing
child restraint using the vehicle seat belt in the
rear seats or in the front passenger seat:
1.If you must install a child restraint in the front
seat, it should be placed in a forward-facing
direction only. Move the seat to the rearmost
position. Child restraints for infants must be
used in the rear-facing direction and, there-
fore, must not be used in the front seat.
2. Position the child restraint on the seat. Always follow the child restraint manufactur-
er’s instructions. The back of the child re-
straint should be secured against the vehicle
seatback. If necessary, adjust or remove the
head restraint/headrest to obtain the correct
child restraint fit. If the head restraint/
headrest is removed, store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is removed.
For additional information about head
restraint/headrest adjustment, removal and
WRS0699ZForward-facing (front passenger seat) — step 1
Safety — seats, seat belts and supplemental restraint system1-31
Page 56 of 556
5. Allow the seat belt to retract. Pull up on theshoulder belt to remove any slack in the belt. 6. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint with your
knee to compress the vehicle seat cushion
and seatback while pulling up on the seat
belt.
7. Tighten the tether strap according to the manufacturer’s instructions to remove any
slack. 8. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten
the seat belt as necessary, or put the re-
straint in another seat and test it again. You
may need to try a different child restraint.
Not all child restraints fit in all types of
vehicles.
9. Check to make sure the child restraint is properly secured prior to each use. If the
seat belt is not locked, repeat steps 2
through 8.
LRS0668ZForward-facing — step 5WRS0681ZForward-facing — step 6WRS0698ZForward-facing — step 8
Safety — seats, seat belts and supplemental restraint system1-33
Page 60 of 556
To avoid injury to a child, do not use the lap/
shoulder belt in the Automatic Locking Retrac-
tor (ALR) mode when using a booster seat with
the seat belts.
For additional information, refer to all Warnings
and Cautions in the Child safetyin the
1. Safety — seats, seat belts and supplemental
restraint system section,Child restraints in
the 1. Safety — seats, seat belts and supple-
mental restraint system section andBooster
seats in the1. Safety — seats, seat belts and
supplemental restraint system section before
installing a child restraint.
Follow these steps to install a booster seat in
the rear seat or in the front passenger seat: 1.
If you must install a booster seat in the front
seat, move the seat to the rearmost position.
2. Position the booster seat on the seat. Only place it in a front-facing direction. Always
follow the booster seat manufacturer’s in-
structions. 3. The booster seat should be positioned on
the vehicle seat so that it is stable.
If necessary, adjust or remove the head
restraint to obtain the correct booster seat
fit. If the head restraint is removed, store it
in a secure place. Be sure to reinstall the
head restraint when the booster seat is re-
moved.
For additional information about head
restraint/headrest adjustment, removal and
installation, refer to Head
restraints/Headrests in the1. Safety —
seats, seat belts and supplemental restraint
system section.
If the seating position does not have an
adjustable head restraint/headrest and it is
interfering with the proper booster seat fit,
WRS0699ZLRS0451ZRear center position
Safety — seats, seat belts and supplemental restraint system1-37
Page 79 of 556
•The supplemental air bag warning light
flashes intermittently.
•The supplemental air bag warning light does
not come on at all.
Under these conditions, the front air bag,
side air bag, curtain air bag, knee air bag or
pretensioner systems may not operate prop-
erly. They must be checked and repaired. It is
recommended that you visit an INFINITI re-
tailer for this service.
WARNING
If the supplemental air bag warning light is on,
it could mean that the front air bag, side air
bag, knee air bag, curtain air bag and/or pre-
tensioner systems will not operate in an acci-
dent. To help avoid injury to yourself or others,
have your vehicle checked as soon as possible.
It is recommended that you visit an INFINITI
retailer for this service.
REPAIR AND REPLACEMENT
PROCEDURE
The front air bags, side air bags, curtain air
bags, knee air bags and pretensioner(s) are
designed to inflate on a one-time-only basis. As
a reminder, unless it is damaged, the supple-
mental air bag warning light remains illumi-
nated after inflation has occurred.
These systems should be repaired and/or re-
placed as soon as possible. It is recommended
that you visit an INFINITI retailer for this service.
When maintenance work is required on the
vehicle, the front air bags, side air bags, curtain
air bags, knee air bags, pretensioner(s) and
related parts should be pointed out to the
person performing the maintenance. The igni-
tion switch should always be in the LOCK
position when working under the hood or inside
the vehicle.
WARNING
•Once a front air bag, side air bag, knee air
bag, or curtain air bag has inflated, the air
bag module will not function again and must
be replaced. Additionally, the activated pre-
tensioner(s) must also be replaced. The air
bag module and pretensioner(s) should be
replaced. It is recommended that you visitan INFINITI retailer for this service. However,
the air bag module and pretensioner(s) can-
not be repaired.
•The front air bag, side air bag, knee air bag,
curtain air bag systems and the preten-
sioner system should be inspected if there
is any damage to the front end or side por-
tion of the vehicle. It is recommended that
you visit an INFINITI retailer for this service.
•If you need to dispose of a supplemental air
bag or pretensioner systems or scrap the
vehicle, it is recommended you visit an
INFINITI retailer. Incorrect disposal proce-
dures could cause personal injury.
•If there is an impact to your vehicle from any
direction, your automatic front-passenger
air bag deactivation system should be
checked to verify it is still functioning cor-
rectly. It is recommended that you visit an
INFINITI retailer for this service. The system
should be checked even if no air bags de-
ploy as a result of the impact. Failure to
verify proper automatic front-passenger air
bag deactivation system function may re-
sult in an improper air bag deployment re-
sulting in injury or death.
1-56Safety — seats, seat belts and supplemental restraint system
** Click HERE to see "Owner's Manual Supplement" **
Page 81 of 556
2 Instruments and controls
Cockpit............................ .2-2
Instrument panel ...................... .2-3
Meters and gauges ..................... .2-4
Speedometer and odometer ...............2-4
Outside temperature display ..............2-5
Tachometer .........................2-5
Engine coolant temperature gauge ..........2-6
Fuel gauge .........................2-6
Warning lights, indicator lights and audible
reminders .......................... .2-8
Checking lights ..................... .2-8
Warning lights ...................... .2-8
Indicator lights ..................... .2-13
Audible reminders ................... .2-14
Vehicle information display ................2-15
Menus and submenus ..................2-16
Display Messages ................... .2-29
Security system ...................... .2-58
Immobiliser ....................... .2-58
Anti-theft alarm system (if equipped) ........2-58
Wiper and washer switch .................2-59
Switching the windshield wipers on/off .......2-60
Switching the rear window wiper on/off .......2-61
Rear window and outside mirror defroster switch . . .2-61
Windshield de-icer switch (if equipped) .........2-62Headlight and turn signal switches
...........2-63
Headlight switch .................... .2-63
Combination switch .................. .2-65
Adaptive front lighting system (LED headlight
only) (if equipped) ................... .2-65
High beam assist (LED headlight only) .......2-67
Headlights misted up on the inside .........2-68
Instrument brightness control .............2-69
Fog light switch (If so equipped) .............2-69
Front fog lights .................... .2-69
Rear fog light ...................... .2-69
Horn .............................
.2-70
Seat heating
(if equipped) .................2-70
Windows .......................... .2-72
Power windows .................... .2-72
Fixed glass roof (if equipped) ...............2-75
Sunshade operation .................. .2-75
Clock ............................. .2-76
Adjusting time ..................... .2-76
Power outlet .........................2-76
Storage ........................... .2-77
Glove box .........................2-78
Front console compartment ..............2-78
Console box ...................... .2-78
Card holder ....................... .2-79