belt INFINITI QX30 2017 Manual PDF

MessagePossible causes/consequences and solutions
[Coolant Too Hot Stop Vehicle
Turn Engine Off] The coolant is too hot.
A warning tone also sounds.
CAUTIONIf the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the
gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle
may seriously damage the engine. For additional information, refer to
If your vehicle overheatsin the6. In case of emergency section
for immediate action required.
1. Stop the vehicle immediately, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Wait until the engine has cooled down.
4. Make sure that the air supply to the engine radiator is not blocked, e.g. by frozen slush.
5. Do not start the engine again until the display message goes out and the coolant temperature is below 120
oC. The engine may
otherwise be damaged.
6. Pay attention to the coolant temperature display.
7. If the temperature increases again, have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
Under normal operating conditions and with the specified coolant level, the coolant temperature may rise to 250
oF (120oC).
See If your vehicle overheats in the6. In case of emergency section.
[See Operator’s Manual] The battery is not being charged.
A warning tone also sounds.
Possible causes:
•Faulty alternator.•Torn poly-V-belt.•A malfunction in the electronics.
CAUTIONDo not continue driving. The engine could otherwise overheat.
1. Stop the vehicle immediately, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Have the system checked. It is recommended you visit an INFINITI retailer for this service.
2-44Instruments and controls

MessagePossible causes/consequences and solutions
[Blind Spot Warning
Inoperative] Blind Spot Warning (BSW) is faulty.
The BSW indicator lights also light up.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Canceled] The driver’s door is open and the driver’s seat belt has not been fastened. Repeat the parking process with the seat belt fastened and the driver’s door closed.
You inadvertently touched the steering wheel while steering intervention was active.
While steering intervention is active, make sure not to touch the steering wheel.
The vehicle has started to skid and VDC has intervened.
Use Intelligent Park Assist again later.
[Park Assist Inoperative] You have just carried out a large number of turning or parking maneuvers. Intelligent Park Assist will become available again after approximately ten minutes.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Restart the engine.
If the display message continues to be displayed, have the system checked. It is recommended you visit an INFINITI retailer for this service.
The parking sensor system is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Finished] The vehicle is parked. A warning tone also sounds. The display message disappears automatically.
[ICC Off] Intelligent Cruise Control has been deactivated (see Intelligent Cruise Control (ICC) system (Full speed range) (if equipped) in the
5. Starting and driving section).
If it was not deactivated by the driver, a warning tone also sounds.
[ICC Now Available] Intelligent Cruise Control is operational again after having been temporarily unavailable. You can now reactivate Intelligent Cruise Control (seeIntelligent Cruise Control (ICC) system (Full speed range) (if equipped) in the5. Starting and driving section)
2-48Instruments and controls

•Never allow anyone to ride in the cargo area
or on the rear seat when it is in the fold-
down position. Use of these areas by pas-
sengers without proper restraints could re-
sult in serious injury or death in an accident
or sudden stop.
•Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts.
•The child restraint top tether strap may be
damaged by contact with items in the cargo
area. Secure any items in the cargo area.
Your child could be seriously injured or
killed in a collision if the top tether strap is
damaged.
•Be sure everyone in your vehicle is in a seat
and using a seat belt properly.
CAUTION
•Do not apply a total load of more than 22 lb
(10 kg) to a single eyelet.
•Secure the load using the cargo tie-down
hooks.
•Distribute the load on the cargo tie-down
hooks evenly.
•Do not use elastic straps or nets to secure a
load. These are only intended as anti-slip
protection for light loads.
•Do not route tie-down ropes or straps across
sharp edges or corners.
•Pad sharp edges for protection.
LUGGAGE HOOKS
The luggage hooks1are for shopping bags,
etc.
CAUTION
•Do not apply a total load of more than 7 lb
(3 kg) to the hook.
•Do not use luggage hooks to secure a load.
NIC2671
Instruments and controls2-81

•Do not fill a portable fuel container in the
vehicle or trailer. Static electricity can cause
an explosion of flammable liquid, vapor or
gas in any vehicle or trailer. To reduce the
risk of serious injury or death when filling
portable fuel containers:– Always place the container on the
ground when filling.
– Do not use electronic devices when fill-
ing.
– Keep the pump nozzle in contact with the
container while you are filling it.
– Use only approved portable fuel contain-
ers for flammable liquid.
CAUTION
•Do not use E-15 or E-85 fuel in your vehicle.
For additional information, refer to Fuel
Recommendation in theTechnical and
consumer information section of this
manual.
•If fuel is spilled on the vehicle body, flush it
away with water to avoid paint damage.
WARNING
•Do not adjust the steering wheel while driv-
ing. You could lose control of your vehicle
and cause an accident.
•Do not adjust the steering wheel any closer
to you than is necessary for proper steering
operation and comfort. The driver’s air bag
inflates with great force. If you are unre-
strained, leaning forward, sitting sideways
or out of position in any way, you are at
greater risk of injury or death in a crash. You
may also receive serious or fatal injuries
from the air bag if you are up against it when
it inflates. Always sit back against the seat-
back and as far away as practical from the
steering wheel. Always use the seat belts. Release the lock lever
1as illustrated and
adjust the steering wheel to the desired posi-
tion (up or down
2, forwards or backwards
3). Firmly push the lock lever back into posi-
tion to lock the steering wheel in place.
NPA1481
STEERING WHEEL
3-16Pre-driving checks and adjustments

seat. If someone becomes trapped, immedi-
ately release the memory function position
button The adjustment is stopped.
•If children activate the memory function,
they could become trapped, especially if
they are unattended. There is a risk of in-
jury.
When leaving the vehicle, always take the
key with you and lock the vehicle. Never
leave children unattended in the vehicle.
The memory function can be used at any time,
e.g. even when the key isn’t in the ignition lock.
STORING SETTINGS
With the memory function, you can store up to
three different settings.
•Seat and seatback position
•Driver’s side: position of the exterior mirrors
on the driver’s and front-passenger sides.
To store settings:
1. Adjust the seat (see Power seat adjustment
in the 1. Safety — seats, seat belts and
supplemental restraint system section).
2. Adjust the exterior mirror on the driver’s side (see Adjusting in the3. Pre-driving checks
and adjustments section).
3. Briefly press the M memory button
1, and
then press preset position button 1, 2 or 3
2within three seconds.
The settings are stored in the selected pre-
set position. A tone sounds when the set-
tings have been completed.
CALLING UP A STORED SETTING
Press and hold the relevant preset position
button 1, 2 or 3 until the seat and exterior
mirrors are in the stored position.
NOTE
The setting procedure is interrupted as soon as
you release the storage position button.
Pre-driving checks and adjustments3-21

If you wish to confirm the restart:
5. Press to confirm.The [Tire Press. Monitor Restarted] message
appears in the vehicle information display.
After you have driven for a few minutes, the
system checks whether the current tire pres-
sures are within the specified range The new
tire pressures are then accepted as refer-
ence values and monitored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher roll-
over rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of perform-
ing in a variety of on-pavement and off-road
applications. This gives them a higher center of
gravity than ordinary vehicles. An advantage of
higher ground clearance is a better view of the
road, allowing you to anticipate problems. How-
ever, they are not designed for cornering at the
same speeds as conventional 2-wheel drive
vehicles any more than low-slung sports cars
are designed to perform satisfactorily underoff-road conditions. If at all possible, avoid
sharp turns at high speeds. As with other
vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or
vehicle rollover. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt.
For additional information, refer to
Driving
safety precautions later in this section.
AVOIDING COLLISION AND ROLLOVER
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of control or
an accident.
Be alert and drive defensively at all times. Obey
all traffic regulations. Avoid excessive speed,
high speed cornering, or sudden steering ma-
neuvers, because these driving practices could
cause you to lose control of your vehicle.
As with any vehicle, loss of control could result
in a collision with other vehicles or objects or
cause the vehicle to roll over, particularly if the
loss of control causes the vehicle to slide side-
ways. Be attentive at all times, and avoid
driving when tired. Never drive when under the
5-10Starting and driving

influence of alcohol or drugs (including pre-
scription or over the- counter drugs which may
cause drowsiness). Always wear your seat belt
as outlined in the “Safety – Seats, seat belts
and supplemental restraint system” section of
this manual, and also instruct your passengers
to do so.
Seat belts help reduce the risk of injury in
collisions and rollovers.In a rollover crash, an
unbelted or improperly belted person is signifi-
cantly more likely to be injured or killed than a
person properly wearing a seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels
may unintentionally leave the road surface. If
this occurs, maintain control of the vehicle by
following the procedure below. Please note that
this procedure is only a general guide. The
vehicle must be driven as appropriate based on
the conditions of the vehicle, road and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
4. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle. 5. If there is nothing in the way, steer the
vehicle to follow the road while vehicle
speed is reduced. Do not attempt to drive
the vehicle back onto the road surface until
vehicle speed is reduced.
6. When it is safe to do so, gradually turn the steering wheel until both tires return to the
road surface. When all tires are on the road
surface, steer the vehicle to stay in the
appropriate driving lane.
If you decide that it is not safe to return the
vehicle to the road surface based on vehicle,
road or traffic conditions, gradually slow the
vehicle to a stop in a safe place off the road.RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged due
to hitting a curb or pothole. Rapid air pressure
loss can also be caused by driving on under-
inflated tires.
Rapid air pressure loss can affect the handling
and stability of the vehicle, especially at high-
way speeds.
Help prevent rapid air pressure loss by main-
taining the correct air pressure and visually
inspect the tires for wear and damage. For
additional information, refer to “Wheels and
tires” in the “Maintenance and do-it-yourself” section of this manual. If a tire rapidly loses air
pressure or “blows-out” while driving, maintain
control of the vehicle by following the proce-
dure below. Please note that this procedure is
only a general guide. The vehicle must be driven
as appropriate based on the conditions of the
vehicle, road and traffic.
WARNING
The following actions can increase the chance
of losing control of the vehicle if there is a
sudden loss of tire air pressure. Losing control
of the vehicle may cause a collision and result
in personal injury.
•The vehicle generally moves or pulls in the
direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
3. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle.
Starting and driving5-11

4. Gradually steer the vehicle to a safe locationoff the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually stop the vehicle.
6. Turn on the hazard warning flashers and contact a roadside emergency service to
change the tire. For additional information,
refer to Flat tire in the6. In case of
emergency section.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of alcohol or
drugs. Alcohol in the bloodstream reduces co-
ordination, delays reaction time and impairs
judgement. Driving after drinking alcohol in-
creases the likelihood of being involved in an
accident injuring yourself and others. Addi-
tionally, if you are injured in an accident, alco-
hol can increase the severity of the injury.
INFINITI is committed to safe driving. However,
you must choose not to drive under the influ-
ence of alcohol. Every year thousands of people
are injured or killed in alcohol-related acci-
dents. Although the local laws vary on what is
considered to be legally intoxicated, the fact is that alcohol affects all people differently and
most people underestimate the effects of alco-
hol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs). Don’t drive if
your ability to operate your vehicle is impaired
by alcohol, drugs, or some other physical con-
dition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal and
off-road use. However, avoid driving in deep
water or mud as your INFINITI is mainly de-
signed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are less
capable than all-wheel drive (AWD) models for
rough road driving and extrication when stuck
in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery sur-
faces may cause the AWD warning message
to display and the AWD system to automati-
cally switch from the AWD to 2WD mode.
This could reduce the traction. Be especially
careful when towing a trailer. (AWD models)
•Drive carefully when off the road and avoid
dangerous areas. Every person who drives
or rides in this vehicle should be seated
with their seat belt fastened. This will keep
you and your passengers in position when
driving over rough terrain.
•Do not drive across steep slopes. Instead
drive either straight up or straight down the
slopes. Off-road vehicles can tip over side-
ways much more easily than they can for-
ward or backward.
•Many hills are too steep for any vehicle. If
you drive up them, you may stall. If you drive
down them, you may not be able to control
your speed. If you drive across them, you
may roll over.
•Do not shift gears while driving on downhill
grades as this could cause loss of control of
the vehicle.
•Stay alert when driving to the top of a hill. At
the top there could be a drop-off or other
hazard that could cause an accident.
•If your engine stalls or you cannot make it to
the top of a steep hill, never attempt to turn
around. Your vehicle could tip or roll over.
5-12Starting and driving

Always back straight down in R (Reverse)
gear and apply brakes to control your
speed.
•Heavy braking going down a hill could cause
your brakes to overheat and fade, resulting
in loss of control and an accident. Apply
brakes lightly and use a low gear to control
your speed.
•Unsecured cargo can be thrown around
when driving over rough terrain. Properly
secure all cargo so it will not be thrown
forward and cause injury to you or your pas-
sengers.
•Secure heavy loads in the cargo area as far
forward and as low as possible. Do not
equip the vehicle with tires larger than
specified in this manual. This could cause
your vehicle to roll over.
•Do not grip the inside or spokes of the steer-
ing wheel when driving off-road. The steer-
ing wheel could move suddenly and injure
your hands. Instead drive with your fingers
and thumbs on the outside of the rim.
•Before operating the vehicle, ensure that
the driver and all passengers have their seat
belts fastened.
•Always drive with the floor mats in place as
the floor may become hot.
•Lower your speed when encountering
strong crosswinds. With a higher center of
gravity, your INFINITI is more affected by
strong side winds. Slower speeds ensure
better vehicle control.
•Do not drive beyond the performance capa-
bility of the tires, even with AWD engaged.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpectedvehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel ex-
cessively.
•Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•If at all possible, avoid sharp turning ma-
neuvers, particularly at high speeds. Your
INFINITI vehicle has a higher center of grav-
ity than a passenger car. The vehicle is not
designed for cornering at the same speeds
as passenger cars. Failure to operate this
vehicle correctly could result in loss of con-
trol and/or a rollover accident.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted, or
radial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•Be sure to check the brakes immediately
after driving in mud or water.
Starting and driving5-13

•Avoid parking your vehicle on steep hills. If
you get out of the vehicle and it rolls for-
ward, backward or sideways, you could be
injured.
•Whenever you drive off-road through sand,
mud or water as deep as the wheel hub,
more frequent maintenance may be re-
quired. For additional information, refer to
Maintenance schedulesin the
9. Maintenance and Schedules section.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS (IF SO
EQUIPPED)
WARNING
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•This vehicle is not designed for offroad
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any D (Drive) or R (Re-
verse) position with the engine running. Do-
ing so may result in drivetrain damage or
unexpected vehicle movement which could
result in serious vehicle damage or personal
injury
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer, (such
as the dynamometers used by some states
for emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpected
vehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively. The INFINITI Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll road
device or automated payment device on the key
ring. Restart the engine using the following
procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK position and wait approximately 5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the device (which may have caused the interference)
separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
INFINITI VEHICLE IMMOBILIZER SYSTEM
5-14Starting and driving