automatic transmission INFINITI QX30 2017 Owner's Manual

•If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS may
not operate correctly.
•Be sure to install the specified size of tires
to all four wheels correctly.
Malfunction Indicator light (MIL)
(yellow)
When the ignition switch is turned to the ON
position, the yellow Malfunction Indicator light
illuminates. This means that the system is
operational.
If the yellow engine malfunction indicator light
lights up while the engine is running, there may
be a fault, for example:
•In the engine management
•In the fuel injection system
•In the exhaust system
•In the ignition system (for vehicles with
gasoline engines)
•In the fuel system
•In other monitored items, for example the
automatic transmission.The emission limit values may be exceeded and
the engine may be running in emergency mode.
CAUTION
Continued vehicle operation without having
the engine control system checked and re-
paired as necessary could lead to poor drive-
ability, reduced fuel economy and possible
damage to the engine control system.
Incorrect setting of the engine control system
may lead to non-compliance of local and na-
tional emission laws and regulations.
Have the vehicle checked as soon as possible. It
is recommended you visit an INFINITI retailer for
this service.
Distance warning light (if
equipped)
This light illuminates if the distance to the
vehicle in front is too small for the speed
selected.
If a warning tone also sounds, you are ap-
proaching a vehicle or stationary obstacle in
your line of travel at too high a speed. For
additional information see Forward emergency
braking (FEB) system (if equipped) in the
5. Starting and driving section.
Electric parking brake
warning light
The red indicator illuminates when the electric
parking brake is engaged.
If the red indicator light for the electric parking
brake flashes or is lit and/or the yellow warning
light for the electric parking brake is lit, observe
the additional messages displayed in the ve-
hicle information display.
For further parking brake operation information
seeParking brake in the3. Pre-driving checks
and adjustments section.
Seat belt (driver and front
passenger) warning light
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion, seeSeat belt reminder chime later
in this section. See Seat beltsin the1. Safety
— seats, seat belts and supplemental restraint
system section for precautions on seat belt
usage.
Instruments and controls2-11

The [From start] trip computer is automatically
reset when:
•The ignition has been switched off for more
than four hours.
•999 hours have been exceeded.
•9999 kilometers have been exceeded.
The [From reset] trip computer is automatically
reset if the value exceeds 9999 hours or 99999
kilometers. Displaying the range and current fuel consump-
tion
:
Press theorbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select
approximate range
1and current fuel con-
sumption
2.
Approximate range
1that can be covered is
calculated according to your current driving
style and the amount of fuel in the tank. If there
is only a small amount of fuel left in the fuel
tank, the display shows a vehicle being refu-
elled instead of approximate range
1. Digital speedometer
:
Press theorbutton on the steering
wheel to select the [Trip] menu.
Press the
orbutton to select digital
speedometer
2.
A gearshift recommendation
1can also be
displayed.
Observe the information on gearshift recom-
mendation
1for automatic transmission (shift-
ing manually) (see Driving with Automatic
Transmission in the5. Starting and driving
section).
NIC2713NIC2714
Instruments and controls2-17

MessagePossible causes/consequences and solutions
[Inoperative See Operator’s
Manual]EBD (electronic brake force distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Contro), and
hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the
,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could therefore lock if
you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to Re-
lease the Parking Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
[Please Release Parking
Brake] The redindicator light flashes and a warning tone sounds. A condition for automatic release of the electric parking brake is not
fulfilled (see Applying automatically (vehicles with automatic transmission) in the5. Starting and driving section).
You are driving with the electric parking brake applied.
Release the electric parking brake manually.
The red
indicator light flashes and a warning tone sounds.
You are making an emergency stop using the electric parking brake (see Emergency brakingin the5. Starting and driving section)
[Parking Brake See Opera-
tor’s Manual] The yellowwarning light lights up.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off.
2. Press the electric parking brake handle for at least ten seconds.
3. Press the P (Park) button.
4. Have the system checked. It is recommended you consult an INFINITI retailer.
2-32Instruments and controls

MessagePossible causes/consequences and solutions
The yellow
warning light and the redindicator light are lit.
The electric parking brake is malfunctioning.
To release:
1. Switch the ignition off and turn it back on.
2. Release the electric parking brake manually.or
3. Release the electric parking brake automatically (see Applying automatically (vehicles with automatic transmission) in the
5. Starting and driving section).
If the electric parking brake still cannot be released: DO NOT drive on. It is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. The redindicator light flashes.
The electric parking brake is malfunctioning.
To release:
1. Switch the ignition off and turn it back on.
2. Release the electric parking brake manually.or
To apply:
1. Switch the ignition off and turn it back on.
2. Apply the electric parking brake manually.
If the red
. indicator light continues to flash:
1 DO NOT drive on
2. Secure the vehicle against rolling away
3. Press the P (Park) button.
4. Turn the front wheels towards the curb.
It is recommended you consult an INFINITI retailer.
Instruments and controls2-33

MessagePossible causes/consequences and solutions
The yellow
warning light is lit. The redindicator light flashes for about ten seconds after the electric parking brake has been
applied or released. It then goes out or remains lit.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off and turn it back on.
2. Apply the electric parking brake manually.If it is not possible to apply the electric parking brake:
3. Press the P (Park) button.
It is recommended you consult an INFINITI retailer.
If it is not possible to release the electric parking brake:
Release the electric parking brake automatically (see Applying automatically (vehicles with automatic transmission) in the5. Starting
and driving section).
If the electric parking: brake still cannot be released, it is recommended you consult an INFINITI retailer.
The yellow
warning light is lit. If you manually apply or release the electric parking brake, the redindicator light flashes.
The electric parking brake is malfunctioning. It is not possible to apply the electric parking brake manually.
or
Insert the seat belt in the belt buckle and accelerate slightly more when pulling away.
Press the P (Park) button, as the electric parking brake is not applied automatically.
It is recommended you consult an INFINITI retailer.
If you do not wish the electric parking brake to be applied, leave the ignition switched on, e. g. when washing the vehicle in an automatic
car wash or when having the vehicle towed.
2-34Instruments and controls

MessagePossible causes/consequences and solutions
[Only Shift to ’P’ when
Vehicle is Stationary] The vehicle is moving.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Shift the shift lever to position P.
[Reversing Not Possible Ser-
vice Required] The automatic transmission is malfunctioning. You cannot drive in reverse.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Transmission Malfunction] The automatic transmission is malfunctioning. Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Transmission Malfunction
Stop] The automatic transmission is malfunctioning.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. It is recommended you consult an INFINITI retailer.
[Stop vehicle Shift to P Leave
Engine Running] The automatic transmission has overheated.
Drive on carefully. If the display message disappears, the automatic transmission is available again.
If the display message continues to be displayed:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Wait until the automatic transmission has cooled down and the display message goes out.
[Auxiliary Battery Malfunc-
tion] The auxiliary battery for the automatic transmission is no longer being charged.
1. It is recommended you visit an INFINITI retailer at the next opportunity.
2. Until then, press the P (Park) button before you switch off the engine.
3. Before leaving the vehicle, apply the electric parking brake.
[Trans. Oil Overheated Drive
On With Care] Manual drive program M and the temporarily active manual drive program are no longer available. Engine power output is reduced
Allow the vehicle to cool down.
[4WD System Currently Un-
available] The 4WD system has overheated. The vehicle is only driven by the front wheels.
Drive on, the airflow cools the 4WD system more quickly.
When the display message goes out, the 4WD system is available again and the vehicle is driven by all four wheels.
[4WD system Inoperative] The 4WD system is malfunctioning. The vehicle is only driven by the front wheels. Have the system checked. It is recommended you visit an INFINITI retailer for this service.
2-54Instruments and controls

If the [Fold Mirrors in when Locking] option has
been activated in the Vehicle information dis-
play:
•The exterior mirrors fold in automatically as
soon as you lock the vehicle from the out-
side.
•The exterior mirrors fold out again automati-
cally as soon as you unlock the vehicle and
then open the driver’s or front-passenger
door.
Automatic parking positioner (if so
equipped)
The Parking position for the exterior mirror on
the front-passenger side function is only avail-
able if the vehicle is equipped with the Memory
package.
1Button for the exterior mirror on the left
hand side.
2Button for the exterior mirror on the right
hand side.
3Adjustment button.
4Memory button M.Setting and storing the parking position using
reverse gear
:
You can set the front-passenger side exterior
mirror so that you can see the rear wheel on
that side as soon as you engage reverse gear.
You can store this position.
1. Make sure that the vehicle is stationary.
2. Switch the ignition switch to the ON posi-
tion.
3. Press button
2for the external mirror on
the front-passenger side.
4. Engage reverse gear. The exterior mirror on the front-passenger side moves to the preset
parking position.
5. Use adjustment button
3to adjust the
exterior mirror. You should see the rear
wheel and the curb in the exterior mirror The
parking position is stored.
NOTE
•If you shift the transmission to another po-
sition, the exterior mirror on the front pas-
senger side returns to the driving position.
•If the driver’s side mirror is currently se-
lected, the passenger side mirror will not
move when reverse gear is engaged.
NIC2639
Pre-driving checks and adjustments3-19

5 Starting and driving
Precautions when starting and driving..........5-4
Exhaust gas (carbon monoxide) ............5-4
Three-way catalyst (if equipped) ............5-4
Tire Pressure Monitoring System (TPMS) .......5-5
On pavement and off-road driving precautions . . .5-10
Avoiding collision and rollover ............5-10
Off-road recovery .................... .5-11
Rapid air pressure loss .................5-11
Drinking alcohol/drugs and driving ..........5-12
Driving safety precautions ...............5-12
All-wheel drive (AWD) driving safety precautions
(if so equipped) .................... .5-14
Infiniti Vehicle Immobilizer system ............5-14
Ignition switch ....................... .5-15
Steering lock ...................... .5-15
Key positions ...................... .5-15
Before starting engine .................. .5-16
Starting engine ....................... .5-16
Starting procedure with the key ............5-16
Driving the vehicle ..................... .5-18
Driving with Automatic Transmission .........5-18
Parking brake .........................5-25
Applying/releasing manually ..............5-25
Applying automatically (vehicles with automatic
transmission) ...................... .5-26Releasing automatically
................5-26
Emergency braking .................. .5-26
Idle Stop/Start System (if equipped) ...........5-27
Automatic engine switch-off ..............5-27
Automatic engine start .................5-28
Deactivating/activating the Idle Stop/Start
function ..........................5-28
L
ane departure warning (LDW) system(if equipped) . .5-29
LDW system operation .................5-30
How to enable/disable the LDW system .......5-31
LDW system limitations .................5-31
LDW system temporarily unavailable .........5-33
System malfunction .................. .5-34
System maintenance ..................5-34
Blind Spot Warning (BSW) system (if equipped) . . . .5-35 BSW system operation .................5-36
How to enable/disable the BSW system ......5-38
BSW system limitations ................5-38
System temporarily unavailable ............5-43
Radar maintenance .................. .5-44
FCC Notice ....................... .5-44
Cruise control ....................... .5-44
Cruise control operations ................5-45

NOTE
For vehicles fitted with Idle Stop/Start System:
When the engine is automatically stopped by
the Idle Stop/Start System the ignition switch
can still be operated as usual.
At the end of a journey turn the ignition OFF to
avoid a discharged battery. The Idle Stop/Start
System does not automatically turn ignition off.•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer fluid
as frequently as possible, or at least when-
ever you refuel.
•Check that all windows and lights are clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view mir-
rors.
•Fasten your seat belt and ask all passengers
to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the ON
position.
STARTING PROCEDURE WITH THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park) by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N (Neu-
tral), you can also start the engine with the
brake pedal depressed.
The starter is designed not to operate if the shift
lever is in any of the driving positions.
NPA1483
BEFORE STARTING ENGINE STARTING ENGINE
5-16Starting and driving

DRIVING WITH AUTOMATIC
TRANSMISSION
Driving precautions
•Do not depress the accelerator pedal while
shifting from P (Park) or N (Neutral) to R (Re-
verse), D (Drive), or M (Manual shift mode).
Always depress the brake pedal until shifting
is completed. Failure to do so could cause you
to lose control and have an accident.
•Cold engine idle speed is high, so use caution
when shifting into a forward or reverse gear
before the engine has warmed up.
•Never shift to either the P (Park) or R (Reverse)
position while the vehicle is moving forward
and P (Park) or D (Drive) position while the
vehicle is reversing. This could cause an acci-
dent or damage the transmission.
•Except in an emergency, do not shift to the N
(Neutral) position while driving. Coasting
with the transmission in the N (Neutral) posi-
tion may cause serious damage to the trans-
mission.
WARNING
•Do not downshift abruptly on slippery
roads. this may cause a loss of control.
CAUTION
•To avoid possible damage to your vehicle;
when stopping the vehicle on an uphill
grade, do not hold the vehicle by depress-
ing the accelerator pedal. The foot brake
should be used for this purpose.
•Except in an emergency, do not shift to the N
(Neutral) position while driving. Coasting
with the transmission in the N (Neutral) po-
sition may cause serious damage to the
transmission.
Starting the vehicle
1. After starting the engine, fully depress thebrake pedal before shifting the shift lever to
R (Reverse), D (Drive) or Manual shift mode.
2. Keep the brake pedal depressed and push the shift lever to shift into a driving gear.
3. Release the parking brake and brake, then gradually put the vehicle in motion by press-
ing the accelerator pedal.
The automatic transmission is designed so that
the brake pedal MUSTbe depressed before
shifting from P (Park) to any drive position while
the ignition switch is ON.
Shifting
P Park position with parking lock
R Reverse
N Neutral
D Drive
NSD585
DRIVING THE VEHICLE
5-18Starting and driving