torque INFINITI QX30 2017 Owner's Manual

VDC warning lightmay illuminate. This
is not a malfunction. Restart the engine af-
ter driving onto a stable surface.
•If wheels or tires other than the INFINITI
recommended ones are used, the VDC sys-
tem may not operate properly and the VDC
warning light
may illuminate.
•The VDC system is not a substitute for win-
ter tires or tire chains on a snow covered
road.
•If VDC is malfunctioning, VDC is unable to
stabilize the vehicle. In addition, other driv-
ing safety systems are switched off. This
increases the risk of skidding and an acci-
dent. Drive on carefully. Have VDC checked.
It is recommended you visit an INFINITI re-
tailer for this service.
CAUTION
•When VDC is deactivated, theVDC
OFF warning light lights up continuously.
•If both thewarning light andwarning light are lit continuously, VDC is
not available due to a malfunction.
TRACTION CONTROL SYSTEM (TCS)
The Traction Control System (TCS) is part of
VDC..
Traction control brakes the drive wheels indi-
vidually if they spin. This enables you to pull
away and accelerate on slippery surfaces, for
example if the road surface is slippery on one
side. In addition, more drive torque is trans-
ferred to the wheel or wheels with traction.
Traction control remains active if you deactivate
VDC.
CHARACTERISTICS OF VDC
If theVDC warning light goes out before
beginning the journey, VDC is automatically
active.
If VDC intervenes, the
VDC warning lamp
flashes in the combination meter.
If VDC intervenes:
•Do not deactivate VDC under any circum-
stances.
•When pulling away, only depress the accel-
erator pedal as far as is necessary.
•Adapt your driving style to suit the prevailing
road and weather conditions.
Deactivating/activating VDC
WARNING
If you deactivate VDC, VDC no longer stabilizes
the vehicle. There is an increased risk of skid-
ding and an accident.
Only deactivate VDC in the situations de-
scribed in the following section.
You can select between the following statuses
of VDC:
•VDC is activated.
•VDC is deactivated.
It may be best to deactivate VDC in the follow-
ing situations:
•When using snow chains.
•In deep snow.
•On sand or gravel.
NOTE
Activate VDC as soon as the situations described
above no longer apply. VDC will otherwise not be
Starting and driving5-91

able to stabilize the vehicle if the vehicle starts
to skid or a wheel starts to spin.
You can activate/deactivate VDC using the ve-
hicle information display. To activate/
deactivate VDC:
1. Start the engine
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu in the vehicle information display.
3. Press the
orbutton to select
VDC.
4. Press the button on the steering wheel.
The current selection is displayed.
5. To activate/deactivate: press the but-
ton again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
Characteristics when VDC is deactivated
:
If VDC is deactivated and one or more wheels
start to spin, theVDC warning lamp
flashes in the combination meter. In such situ-
ations, VDC will not stabilize the vehicle. If you deactivate VDC:
•VDC no longer intervenes in understeer or
oversteer situations.
•Engine torque is no longer limited and the
drive wheels are able to spin.
The spinning of the wheels results in a
cutting action, so the tires cut through the
loose surface until the hit solid ground,
giving better traction.
•Traction control is still activated.
•VDC still provides support when you brake.
EBD (ELECTRONIC BRAKE FORCE
DISTRIBUTION)
EBD monitors and controls the brake pressure
on the rear wheels to help improve handling
during braking.
WARNING
If EBD is malfunctioning, the EBD [Inoperative
See Operator’s Manual] warning is displayed
in the vehicle information display. The
VDC warning lamp may also light up.
If EBD is malfunctioning as a result of a VDC
malfunction, the rear wheels can lock, e.g. un-
der full braking. This increases the risk of skid-
ding and an accident.You should therefore adapt your driving style
to the different handling characteristics. Have
the brake system checked. It is recommended
you see an INFINITI retailer.
STEER CONTROL
STEER CONTROL helps you by transmitting a
noticeable steering force to the steering wheel
in the direction required for vehicle stabilisa-
tion.
This steering support is provided in particular if:
•Both right wheels or both left wheels are on
a wet or slippery road surface when you
brake.
•The vehicle starts to skid.
WARNING
No steering support is provided from STEER
CONTROL, if:
•VDC is malfunctioning.
•The steering is faulty.
Power steering will, however, continue to
function.
5-92Starting and driving

5. Tighten the wheel bolts securely using thewheel wrench in the sequence as illustrated.
6. Lower the vehicle completely.
7. Install the wheel cover (if equipped).
Wheel
bolt tightening torque:96 ft-lb (130 N•m, 13
kg-m)
As soon as possible, tighten the wheel bolts to
the specified torque with a torque wrench.
The wheel bolts must be kept tightened to
specification at all times. It is recommended
that the wheel bolts be tightened to specifica-
tion at each maintenance interval.
Adjust the tire pressure to the COLD pressure.
COLD pressure is the tire pressure as measured
after the vehicle has been parked for three
hours or more or driven for less than 1 mile (1.6
km).
COLD tire pressures are shown on the tire and
loading information label affixed to the driver’s
side center pillar.
Wheel lock bolts (if equipped)
In order to prevent theft, the specially designed
wheel lock bolt is installed to each wheel. The
wheel lock bolt cannot be removed with the
commonly used tools. When removing tires, use the lock key provided
with your vehicle.
Removing the wheel lock bolt
:
1. Insert the wheel lock key1to the wheel
lock bolt.
2. To remove the wheel lock bolt, turn the wheel lock key counterclockwise using the
wheel wrench.
CAUTION
•Do not use a power tool to remove the wheel
lock bolts.
•When installing the wheel, tighten the
wheel lock bolts to the same tightening
torque as the normal wheel bolts. For de-
tails, see Installing the wheel earlier in
this section. NOTE
•The wheel lock bolt has an individual code. A
wheel lock key with other than the individual
code cannot remove the wheel lock bolt. If
you lose the wheel lock key, it is recom-
mended you contact an INFINITI retailer for a
duplicate with the original wheel lock key
code.
•Record the key number and keep it in a safe
place, not in the vehicle.
•When you ask for a service at an INFINITI
retailer, make sure to keep the lock key in
the vehicle. Otherwise, wheels cannot be
removed and the service cannot be per-
formed.
NCE143Z
In case of emergency6-9

1. Park the vehicle on a level surface and applythe parking brake.
2. Start the engine and let it idle until it reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it coun- terclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer to Changing
engine oil filter later in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with
a wrench. Do not use excessive force.Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer to Recommended fluids/
lubricants and capacities in the
9. Maintenance and Schedules section.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10 minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and applythe parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

5. Wipe the engine oil filter sealing surface witha clean rag.
CAUTION
•Be sure to remove any old gasket material
remaining on the sealing surface of the en-
gine. Failure to do so could lead to an oil
leak and engine damage.
•The dipstick must be inserted in place to
prevent oil spillage from the dipstick hole
when filling the engine with oil.
6. Coat the gasket on the new filter with clean engine oil.
7. Screw on the oil filter until a slight resis- tance is felt, then tighten an additional
2/3 turn. Engine oil filter tightening torque:
19 ft-lb, 25 N•m
8. Start the engine and check for leakage around the oil filter. Correct as required.
9. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil
if necessary. It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
CAUTION
•Use only Shell DCT-M1 or equivalent. Do not
mix with other fluids.
•Using automatic transmission fluid other
than Shell DCT-M1 may cause deterioration
in driveability and automatic transmission
durability, and may damage the automatic
transmission. Damage caused by the use of
fluids other than as recommended is not
covered by the warranty.
WARNING
•Use only new fluid. Old, inferior, or contami-
nated fluid may damage the brake systems.
The use of improper fluids can damage the
brake system and affect the vehicle’s stop-
ping ability.
•Clean the filler cap before removing.
•Brake fluid is poisonous and should be
stored carefully in marked containers out of
the reach of children.
CAUTION
•Do not spill the fluid on painted surfaces.
This will damage the paint. If fluid is spilled,
wash with water.
NDI1599
AUTOMATIC TRANSMISSION FLUID (ATF) BRAKE FLUID
Do-it-yourself8-7

some tire damage may not be obvious. Re-
place the tires as necessary to prevent tire
failure and possible personal injury.
•Improper service of the spare tire may result
in serious personal injury. If it is necessary
to repair the spare tire, it is recommended
that you visit an INFINITI retailer for this
service.
•For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada)
in the Warranty Information Booklet.
Tires should be periodically inspected for wear,
cracking, bulging or objects caught in the tread.
If excessive wear, cracks, bulging or deep cuts
are found, the tire should be replaced immedi-
ately.
The original tires have a built-in tread wear
indicator. When the wear indicator is visible,
the tire should be replaced.
Improper servicing of a tire may result in seri-
ous personal injury. If it is necessary to repair a
tire, it is recommended you contact an INFINITI
retailer.
TIRE ROTATION
INFINITI recommends rotating the tires every
5,000 miles (8,000 km).
For additional information on tire replacing
procedures, refer to Flat tirein the6. In case
of emergency section.As soon as possible,
tighten the wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque: 96 ft-lb (130 N·m)
The wheel nuts must be kept tightened to speci-
fications at all times. It is recommended that
wheel nuts be tightened to specification at each
tire rotation interval.
WARNING
•After rotating the tires, check and adjust the
tire pressure.
•Do not include the spare tire in the tire rota-
tion.
•For additional information regarding tires,
refer to Important Tire Safety Information
(US) or Tire Safety Information in the War-
ranty Information Booklet.
REPLACING WHEELS AND TIRES
WARNING
Do not install a deformed wheel or tire even if it
has been repaired. Such wheels or tires could
have structural damage and could fail without
warning.
When replacing a tire, use the same size, speed
rating and load carrying capacity as originally
equipped. (See Wheels and Tires in the
9. Maintenance and Schedules section for
recommended types and sizes of tires and
wheels.)
If the wheels are changed for any reason,
always replace with wheels which have the
same offset dimension. Wheels of a different
offset could cause early tire wear, possibly
degraded vehicle handling characteristics
and/or interference with the brake discs/
drums. Such interference can lead to decreased
braking efficiency and/or early brake pad/shoe
wear.
8-32Do-it-yourself