light INFINITI QX30 2018 Owners Manual

The Idle Stop/Start function switches the
engine off automatically if the vehicle is
stopped under certain conditions.
When pulling away again, the engine starts
automatically. The Idle Stop/Start function
thereby helps you to reduce the fuel con-
sumption and emissions of your vehicle.
WARNING
If the engine is switched off automatically
and you exit the vehicle, the engine is re-
started automatically. The vehicle may be-
gin moving There is a risk of accident and
injury.
If you wish to exit the vehicle, always turn
off the ignition and secure the vehicle
against rolling away.If the
Idle Stop/Start symbol is shown
in green in the vehicle information display, the
Idle Stop/Start function switches the engine
off automatically once the vehicle stops mov-
ing.
The Idle Stop/Start function is automatically
activated each time you start the engine with
the ignition key.
If the Idle Stop/Start function has been
manually deactivated (see "Deactivating/
activating the Idle Stop/Start function" later
in this section) or a malfunction has caused
the system to be deactivated, the
Idle
Stop/Start symbol is not displayed.
AUTOMATIC ENGINE
SWITCH-OFF
The Idle Stop/Start function is operational
and theIdle Stop/Start symbol is dis-
played in green in the vehicle information dis-
play, if:
•The indicator light in the ECO button is lit
green.
•The outside temperature is within the
range that is suitable for the system.
•The engine is at normal operating tem-
perature.
•The set temperature for the vehicle interior
has been reached.
•The battery is sufficiently charged.
•The system detects that the windshield is
not misted up when the air-conditioning
system is switched on.
•The hood is closed.
•The driver's door is closed and the driver's
seat belt is fastened.
If the conditions for automatic engine
switch-off are not all fulfilled, the
Idle
Stop/Start symbol is shown in yellow.
NSD620
Idle Stop/Start symbol
IDLE STOP/START SYSTEM (IF
EQUIPPED)
Starting and driving5-29

All of the vehicle's systems remain active
when the engine is switched off automati-
cally.
The engine can be switched off automatically
a maximum of four times (initial stop, then
three subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yel-
low in the vehicle information display after
the engine has been started automatically for
the fourth time. When the
Idle Stop/
Start symbol is shown in green in the vehicle
information display, automatic engine
switch-off is again possible.
NOTE
If the hood is opened while the engine is run-
ning and the Idle Stop/Start function is op-
erational, the engine will switch off auto-
matically.
If the vehicle is brought to a standstill in D or
N, the Idle Stop/Start function switches off
the engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start func-
tion by pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver's door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior de-
viates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery's charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you shift the transmission from R (Reverse)
to D (Drive), the Idle Stop/Start function is
available again once the
Idle Stop/
Start symbol reappears in green in the vehicle
information display.
DEACTIVATING/ACTIVATING
THE IDLE STOP/START
FUNCTION
•To deactivate: press ECO button1. Indi-
cator light
2and theIdle Stop/
Start symbol in the vehicle information dis-
play turn off.
•To activate: press ECO button1. Indica-
tor light
2lights up. If all conditions for
automatic engine switch-off (see "Auto-
matic engine switch-off" earlier in this sec-
tion) are fulfilled, the
Idle Stop/Start
symbol is shown in green in the vehicle
information display.
NIC2633
5-30Starting and driving

If not all conditions for automatic engine
switch-off are met, theIdle Stop/
Start symbol is lit yellow in the vehicle
information display. If this is the case, the
Idle Stop/Start function is not active.
If indicator light
2on ECO button1is off,
the Idle Stop/Start function has been deacti-
vated manually or as the result of a malfunc-
tion. The engine will then not be switched off
automatically when the vehicle stops.
WARNING
Failure to follow the warnings and instruc-
tions for proper use of the LDW system
could result in serious personal injury or
death. The LDW system will not steer the
vehicle or prevent loss of control. It is the
driver’s responsibility to stay alert, drive
safely, keep the vehicle in the traveling
lane, and be in control of the vehicle at all
times.
The LDW system warns the driver with a
warning light and intermittent steering vibra-
tion that the vehicle is beginning to leave the
traveling lane. The LDW system uses a camera
1installed
behind the windshield to monitor the lane
markers of your traveling lane.
NSD644
LANE DEPARTURE WARNING (LDW)
SYSTEM (IF EQUIPPED)
Starting and driving5-31

•The system will not operate at speeds
below approximately 40 MPH (60
km/h) or if it cannot detect lane mark-
ers.
•The LDW system is primarily intended
for use on well-developed freeways or
highways. It may not detect the lane
markers in certain roads, weather or
driving conditions.
•Do not use the LDW system under the
following conditions as it may not func-
tion properly: – During bad weather (rain, fog, snow,
etc.).
– When driving on slippery roads, such
as on ice or snow, etc.
– When driving on winding or uneven
roads.
– When there is a lane closure due to
road repairs.
– When driving in a makeshift or tem-
porary lane.
– When driving on roads where the lane
width is too narrow.
– When driving without normal tire
conditions (for example, tire wear,
low tire pressure, installation of
spare tire, tire chains, non-standard
wheels). –
When the vehicle is equipped with
non-original brake parts or suspen-
sion parts.
•The camera may not detect lane markers
in the following situations and the LDW
system may not operate properly. – On roads where there are multiple
parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; non-
standard lane markers; or lane mark-
ers covered with water, dirt, snow,
etc.
– On roads where the discontinued lane
markers are still detectable.
– On roads where there are sharp
curves.
– On roads where there are sharply
contrasting objects, such as shad-
ows, snow, water, wheel ruts, seams
or lines remaining after road repairs.
(The LDW system could detect these
items as lane markers.)
– On roads where the traveling lane
merges or separates.
– When the vehicle’s traveling direc-
tion does not align with the lane
marker.
– When traveling close to the vehicle in
front of you, which obstructs the lane
camera unit detection range. –
When rain, snow or dirt adheres to
the windshield in front of the lane
camera unit.
– When the headlights are not bright
due to dirt on the lens or if the aiming
is not adjusted properly.
– When strong light enters the lane
camera unit. (For example, the light
directly shines on the front of the ve-
hicle at sunrise or sunset.)
– When a sudden change in brightness
occurs. (For example, when the ve-
hicle enters or exits a tunnel or under
a bridge.)
– When there is poor visibility. (For ex-
ample, due to insufficient illumina-
tion of the road, or due to snow, rain,
fog or spray.
– When there is glare. (For example,
from oncoming traffic, the sun or re-
flection when the road is wet).
5-34Starting and driving

SYSTEM MAINTENANCE
The lane camera unit1for the LDW system
is located above the inside mirror.
To ensure the proper operation of the LDW
system and prevent a system malfunction, be
sure to observe the following:
•Always keep the windshield clean.
•Do not attach a sticker (including transpar-
ent material) or install an accessory near
the camera unit.
•Do not place reflective materials, such as
white paper or a mirror, on the instrument
panel. The reflection of sunlight may ad-
versely affect the camera unit’s capability
of detecting the lane markers.
•Do not strike or damage the areas around
the camera unit. Do not touch the camera
lens or remove parts from the camera unit.
If the camera unit is damaged due to an
accident, it is recommended you contact
an INFINITI retailer.WARNING
Failure to follow the warnings and instruc-
tions for proper use of the BSW system
could result in serious injury or death.
•The Blind Spot Warning (BSW) system
is not a replacement for proper driving
procedure and is not designed to pre-
vent contact with vehicles or objects.
When changing lanes, always use the
side and rear mirrors and turn and look in
the direction you will move to ensure it is
safe to change lanes. Never rely solely
on the BSW system.
The Blind Spot Warning (BSW) system can
help alert the driver of other vehicles in adja-
cent lanes when changing lanes.
NSD644
BLIND SPOT WARNING (BSW)
SYSTEM (IF EQUIPPED)
5-36Starting and driving

BSW SYSTEM OPERATION
1Side indicator light
2Steering wheel mounted controls
3Vehicle information display
AMENU barThe BSW system operates above approxi-
mately 20 MPH (30 km/h). When the BSW is
activated, the side indicator light illuminates
in yellow up to a speed of 20 MPH (30
km/h). At speeds above 20 MPH (30 km/h),
the indicator light goes out and the BSW
system is operational. Illustration 1:
If the radar sensors detect a
vehicle in the detection zone, the BSW indi-
cator light
1located by the outside mirrors
illuminates.
NSD623
SSD1026Z
Illustration 1
5-38Starting and driving

Illustration 2:If the turn signal is then acti-
vated, the system chimes (twice) and the
BSW indicator light flashes. The BSW indica-
tor light continues to flash until the detected
vehicles leave the detection zone.
NOTE
•The BSW indicator lights illuminate for a
few seconds when the ignition switch is
placed in the ON position.
•The brightness of the BSW indicator lights
is adjusted automatically depending on the
brightness of the ambient light.
•If a vehicle comes into the detection zone
after the driver activates the turn signal,
then only the BSW indicator light flashes
and no chime sounds. (See "Another ve-
hicle approaching from behind" later in this
section.)
A chime sounds if the radar sensors have
already detected vehicles when the driver ac-
tivates the turn signal.
WARNING
•Do not use the BSW system when tow-
ing a trailer because the system may not
function properly.
•Excessive noise (for example audio sys-
tem volume, open vehicle window) will
interfere with the chime sound, and it
may not be heard.
•The radar sensors may not be able to
detect and activate BSW when certain
objects are present such as: – Pedestrians, bicycles, animals
– Several types of vehicles such as mo-
torcycles
– Oncoming vehicles
– Vehicles remaining in the detection
zone when you accelerate from a
stop. –
A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
– A vehicle approaching rapidly from
behind.
– A vehicle which your vehicle over-
takes rapidly.
•Severe weather or road spray conditions
may reduce the ability of the radar to
detect other vehicles.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar
sensors may not detect vehicles in an
adjacent lane. When driving in a narrow
lane, the radar sensors may detect ve-
hicles driving two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however ob-
jects such as guardrails, walls, foliage
and parked vehicles may occasionally be
detected. This is a normal operating
condition.
SSD1031Z
Illustration 2
Starting and driving5-39

–Vehicles such as motorcycles, low
height vehicles, or high ground clear-
ance vehicles.
– Oncoming vehicles.
– Vehicles remaining in the detection
zone when you accelerate from a
stop.
– A vehicle merging into an adjacent
lane at a speed approximately the
same as your vehicle.
– A vehicle that is too close to your
vehicle.
– A vehicle approaching rapidly from
behind.
– A vehicle which your vehicle over-
takes rapidly.
•The radar sensors detection zone is de-
signed based on a standard lane width.
When driving in a wider lane, the radar
sensors may not detect vehicles in an
adjacent lane. When driving in a narrow
lane, the radar sensors may detect ve-
hicles driving two lanes away.
•The radar sensors are designed to ignore
most stationary objects, however ob-
jects such as guardrails, walls, foliage
and parked vehicles may occasionally be
detected. This is a normal operating
condition.
•The following conditions may reduce the
ability of the radar to detect other ve-
hicles: – Severe weather
– Road spray
– Ice/frost/dirt build-up on the vehicle
•Do not attach stickers (including trans-
parent material), install accessories or
apply additional paint near the radar
sensors. These conditions may reduce
the ability of the radar to detect other
vehicles.
•Do not use the BSW system when tow-
ing a trailer because the system may not
function properly.
•Excessive noise (e.g. audio system vol-
ume, open vehicle window) will interfere
with the chime sound, and it may not be
heard.
•The BSW system may not provide a
warning for vehicles that pass through
the detection zone quickly.
Another vehicle approaching from
behind
Illustration 1: The BSW indicator light illumi-
nates if a vehicle enters the detection zone
from behind in an adjacent lane.
However, if the overtaking vehicle is travel-
ling much faster than your vehicle, the indica-
tor light may not illuminate before the de-
tected vehicle is beside your vehicle. Always
use the side and rear mirrors and turn and
look in the direction your vehicle will move to
ensure it is safe to change lanes.
SSD1026Z
Illustratio n 1 – Approaching from behind
Starting and driving5-41

Illustration 2: If the driver activates the turn
signal, then the system chimes (twice) and the
BSW indicator light flashes.
NOTE
•The radar sensors may not detect vehicles
which are approaching rapidly from be-
hind.
•If the driver activates the turn signal be-
fore a vehicle enters the detection zone,
the BSW indicator light will flash but no
chime will sound when the other vehicle is
detected.
Accelerate from a stop
NOTE
Illustration 3: If you accelerate from a stop
with a vehicle in the detection zone, the
other vehicle may not be detected.
Overtaking another vehicle
When you overtake a vehicle, the warning
only occurs if the difference in speed is less
than 7 MPH (12 km/h).
Illustration 4: The side indicator light illumi-
nates if you overtake a vehicle and that ve-
hicle stays in the detection zone for approxi-
mately 3 seconds.
SSD1031Z
Illustratio n 2 – Approaching from behind
SSD1032Z
Illustration3–Acceleratefromastop
SSD1033Z
Illustration 4 – Overtaking another vehicle
5-42Starting and driving

Illustration 5: If the driver activates the turn
signal while another vehicle is in the detection
zone, then the system chimes (twice) and the
BSW indicator light flashes.
NOTE
•When overtaking several vehicles in a row,
the vehicles after the first vehicle may not
be detected if they are travelling close to-
gether.
•The radar sensors may not detect slower
moving vehicles if they are passed quickly.
•If the driver activates the turn signal be-
fore a vehicle enters the detection zone,
the side indicator light will flash but no
chime will sound when the other vehicle is
detected.
Overtaking several vehicles
Illustration 6: When overtaking several ve-
hicles in a row, the vehicles after the first
vehicle may not be detected if they are trav-
elling close together.
SSD1034Z
Illustratio n 5 – Overtaking another vehicle
SSD1036Z
Illustration 6 – Overtaking several vehicles
Starting and driving5-43