instrument panel INFINITI QX30 2018 Owners Manual

0 Illustrated table of contents
Seats, Seat belts and Supplemental Restraint
System (SRS)....................... .0-2
Exterior front ....................... .0-3
Exterior rear ........................ .0-4
Passenger compartment .................0-5
Cockpit ........................... .0-6Instrument panel
..................... .0-7
Meters and gauges .................... .0-8
Engine compartment .................. .0-9
2.0L Gasoline engine ................ .0-9
Warning and indicator lights ..............0-10

1. Ventilators (P.4-42)
2. Center display* (P.4-4)
3. Meters and gauges (P.2-4)
4. Light switch (P.2-64)
5. Parking brake (P.3-27)6. Steering wheel
— Power steering system (P.5-90)
— Horn (P. 2-71)
— Driver’s supplemental front-impact air
bag (P.1-38)
7. Audio system (P.4-53) 8. Ignition switch (P.5-15)
— Push button ignition switch* (P.5-16)
9. Heater and air conditioner (P.4-43)
10. Switch panel — Seat heater switches* (P.2-72)
— Hazard indicator flasher switch (P.6-2)
— Idle Stop/Start system on/off switch
(P. 6-30)
— Front passenger air bag status light
(P.6-46)
11. Vehicle Information Display (P.2-15)
12. Glove box (P.2-79)
13. Front passenger supplemental air bag (P.1-38)
*: if equipped
NIC2898
INSTRUMENT PANEL
Illustrated table of contents0-7

Curtain air bags are also designed to inflate in
certain types of rollover collisions or near
rollovers. As a result, certain vehicle move-
ments (for example, during severe off-
roading) may cause the curtain air bags to
inflate.
The SRS is designed tosupplementthe crash
protection provided by the driver and front
passenger seat belts and is not a substitute
for them. Seat belts should always be cor-
rectly worn and the occupant seated a suit-
able distance away from the steering wheel,
instrument panel and front door finishers. For
additional information, see "Seat belts" earlier
in this section.
The supplemental air bags operate only
when the ignition switch is placed in the ON
position.
After placing the ignition switch in the ON,
the air bag warning light will illuminate. The
air bag warning light will turn off within a
few seconds after the engine is started if the
system is operational. See "Warning lights,
indicator lights and audible reminders" in the
"2. Instruments and controls" section for
further details.
WRS0031Z
Sit upright and well back
ARS1133Z
Sit upright and well back
Safety — seats, seat belts and supplemental restraint system1-39

SUPPLEMENTAL AIR BAG
SYSTEMS
1. Crash zone sensor
2. Supplemental front-impact air bag mod-ules 3. Front seat-mounted side-impact supple-
mental air bag modules
4. Roof-mounted curtain side-impact and rollover supplemental air bag inflators
5. Roof-mounted curtain side-impact and rollover supplemental air bag modules 6. Driver and passenger supplemental knee
air bags
7. Front door pressure sensors
8. Front seat belt with pretensioners
9. Satellite sensors
10. Air bag Control Unit (ACU)
11. Rear seat belt with pretensioners
Infiniti Advanced Air Bag System
(front seats)
WARNING
To ensure proper operation of the passen-
ger's INFINITI Advanced Air Bag System,
please observe the following items:
•If a forward-facing child restraint is in-
stalled in the front passenger seat, do
not position the front passenger seat so
the child restraint contacts the instru-
ment panel. If the child restraint does
contact the instrument panel, the sys-
tem may determine the seat is occupied
and the passenger air bag may deploy in
a collision. For additional information
about installing and using child re-
straints, refer to "Child restraints" in the
"1. Safety — seats, seat belts and
supplemental restraint system" section.
NIC2754
1-44Safety — seats, seat belts and supplemental restraint system

Other supplemental front-impact
air bag precautions
WARNING
•Do not place any objects on the steering
wheel pad or on the instrument panel.
Also, do not place any objects between
any occupant and the steering wheel or
instrument panel. Such objects may be-
come dangerous projectiles and cause
injury if the front air bags inflate.
•Immediately after inflation, several
front air bag system components will be
hot. Do not touch them; you may se-
verely burn yourself.
•No unauthorized changes should be
made to any components or wiring of
the supplemental air bag system. This is
to prevent accidental inflation of the
supplemental air bag or damage to the
supplemental air bag system.
•Do not make unauthorized changes to
your vehicle's electrical system, suspen-
sion system or front end structure. This
could affect proper operation of the
front air bag system.
•Tampering with the front air bag system
may result in serious personal injury. Tam-
pering includes changes to the steering
wheel and the instrument panel assembly
by placing material over the steering wheel
pad and above the instrument panel or by
installing additional trim material around
the air bag system.
•Removing or modifying the front pas-
senger seat may affect the function of
the air bag system and result in serious
personal injury.
•Modifying or tampering with the front
passenger seat may result in serious
personal injury. For example, do not
change the front seats by placing mate-
rial on the seat cushion or by installing
additional trim material, such as seat
covers, on the seat that are not specifi-
cally designed to assure proper air bag
operation. Additionally, do not stow any
objects under the front passenger seat
or the seat cushion and seatback. Such
objects may interfere with the proper
operation of the occupant classification
sensor (pressure sensor).
•No unauthorized changes should be
made to any components or wiring of the seat belt system. This may affect the
front air bag system. Tampering with
the seat belt system may result in seri-
ous personal injury.
•It is recommended that you visit an
INFINITI retailer for work on and around
the front air bag. It is also recommended
that you visit an INFINITI retailer for
installation of electrical equipment. The
Supplemental Restraint System (SRS)
wiring harnesses* should not be modi-
fied or disconnected. Unauthorized
electrical test equipment and probing
devices should not be used on the air bag
system.
•A cracked windshield should be replaced
immediately by a qualified repair facil-
ity. A cracked windshield could affect
the function of the supplemental air bag
system.
* The SRS wiring harness connectors are
yellow and orange for easy identification.
When selling your vehicle, we request that
you inform the buyer about the front air bag
system and guide the buyer to the appropri-
ate sections in this Owner's Manual.
Safety — seats, seat belts and supplemental restraint system1-51

SUPPLEMENTAL AIR BAG
WARNING LIGHT
The supplemental air bag warning light, dis-
playingin the instrument panel, moni-
tors the circuits for the air bag systems, pre-
tensioner(s) and all related wiring.
When the ignition switch is placed in the ON
position, the supplemental air bag warning
light illuminates. The air bag warning light will
turn off within a few seconds after the engine
is started, if the system is operational.
If any of the following conditions occur, the
front air bag, side air bag, curtain air bag and
pretensioner systems need servicing:
•The supplemental air bag warning light
remains on after approximately 7 seconds.
•The supplemental air bag warning light
flashes intermittently.
•The supplemental air bag warning light
does not come on at all.
Under these conditions, the front air bag,
side air bag, curtain air bag, knee air bag or
pretensioner systems may not operate
properly. They must be checked and re-
paired. It is recommended that you visit an
INFINITI retailer for this service.
WARNING
If the supplemental air bag warning light is
on, it could mean that the front air bag, side
air bag, knee air bag, curtain air bag and/or
pretensioner systems will not operate in an
accident. To help avoid injury to yourself or
others, have your vehicle checked as soon
as possible. It is recommended that you
visit an INFINITI retailer for this service.
REPAIR AND REPLACEMENT
PROCEDURE
The front air bags, side air bags, curtain air
bags, knee air bags and pretensioner(s) are
designed to inflate on a one-time-only basis.
As a reminder, unless it is damaged, the
supplemental air bag warning light remains
illuminated after inflation has occurred. These systems should be repaired and/or re-
placed as soon as possible. It is recom-
mended that you visit an INFINITI retailer for
this service.
When maintenance work is required on the
vehicle, the front air bags, side air bags, cur-
tain air bags, knee air bags, pretensioner(s)
and related parts should be pointed out to the
person performing the maintenance. The ig-
nition switch should always be in the LOCK
position when working under the hood or
inside the vehicle.
WARNING
•Once a front air bag, side air bag, knee
air bag, or curtain air bag has inflated,
the air bag module will not function
again and must be replaced. Addition-
ally, the activated pretensioner(s) must
also be replaced. The air bag module and
pretensioner(s) should be replaced. It is
recommended that you visit an INFINITI
retailer for this service. However, the air
bag module and pretensioner(s) cannot
be repaired.
•The front air bag, side air bag, knee air
bag, curtain air bag systems and the
pretensioner system should be in-
spected if there is any damage to the
front end or side portion of the vehicle. It
SPA1097Z
1-56Safety — seats, seat belts and supplemental restraint system

2 Instruments and controls
Cockpit........................... .2-2
Instrument panel ..................... .2-3
Meters and gauges .................... .2-4
Speedometer and odometer .............2-4
Outside temperature display .............2-5
Tachometer ...................... .2-6
Engine coolant temperature gauge .........2-6
Fuel gauge ....................... .2-7
Warning lights, indicator lights and audible
reminders .......................... .2-8
Checking lights .................... .2-8
Warning lights ..................... .2-8
Indicator lights .................... .2-13
Audible reminders .................. .2-14
Vehicle information display ...............2-15
Menus and submenus ............... .2-16
Display Messages .................. .2-29
Security system ..................... .2-59
Immobiliser ...................... .2-59
Anti-theft alarm system (if equipped) .......2-59
Wiper and washer switch ................2-60
Switching the windshield wipers on/off .....2-61
Switching the rear window wiper on/off . . . .2-62
Rear window and outside mirror defroster
switch ........................... .2-63
Windshield de-icer switch (if equipped) .......2-63
Headlight and turn signal switches ..........2-64Headlight switch
.................. .2-64
Combination switch ................ .2-66
Adaptive front lighting system
(LED headlight only) (if equipped) .........2-67
High beam assist (LED headlight only) ......2-68
Headlights misted up on the inside ........2-70
Instrument brightness control ...........2-70
Fog light switch (If so equipped) ............2-70
Front fog lights ................... .2-70
Rear fog light ..................... .2-71
Horn ............................ .2-71
Seat
heating (if equipped) ............... .2-72
Windows ......................... .2-73
Power windows ................... .2-73
Fixed glass roof (if equipped) ..............2-76
Sunshade operation ................ .2-76
Clock ............................ .2-77
Adjusting time .................... .2-77
Power outlet ....................... .2-78
Storage .......................... .2-79
Glove box ....................... .2-79
Front console compartment ............2-79
Console box ..................... .2-80
Card holder ...................... .2-80
Cup holders ..................... .2-80
Coat hooks ...................... .2-81
Cargo tie-down hooks ............... .2-81

1. Ventilators (P.4-42)
2. Center display* (P.4-4)
3. Meters and gauges (P.2-4)
4. Light switch (P.2-64)
5. Parking brake (P.3-27)6. Steering wheel
— Power steering system (P.5-90)
— Horn (P. 2-71)
— Driver’s supplemental front-impact air
bag (P.1-38)
7. Audio system (P.4-53) 8. Ignition switch (P.5-15)
— Push button ignition switch* (P.5-16)
9. Heater and air conditioner (P.4-43)
10. Switch panel — Seat heater switches* (P.2-72)
— Hazard indicator flasher switch (P.6-2)
— Idle Stop/Start system on/off switch
(P. 6-30)
— Front passenger air bag status light
(P.6-46)
11. Vehicle Information Display (P.2-15)
12. Glove box (P.2-79)
13. Front passenger supplemental air bag (P.1-38)
*: if equipped
NIC2898
INSTRUMENT PANEL
Instruments and controls2-3

Freeway mode
Freeway mode adjusts the light beam to re-
duce the amount of light that shines on the
opposite lane of the freeway, and oncoming
traffic.
Freeway mode is active if you are driving at a
speed above 68 MPH (110 km/h) and do not
make any large steering movements for at
least 3300 ft (1000 m) or if you are driving at
a speed above 81 MPH (130 km/h).
It is not active if you are driving at speeds
below 50 MPH (80 km/h) following activa-
tion.
HIGH BEAM ASSIST (LED
HEADLIGHT ONLY)
You can use this function to set the head-
lights to change between low beam and high
beam automatically. The system recognizes
vehicles with their lights on, either approach-
ing from the opposite direction or traveling in
front of your vehicle, and consequently
switches the headlights from high beam to
low beam.
The system automatically adapts the low
beam headlight range depending on the dis-
tance to the other vehicle. Once the system
no longer detects any other vehicles, it
switches on the high beam headlights again.
The system's optical sensor is located behind
the windshield near the overhead control
panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe
driving operation. The driver should re-
main alert at all times, ensure safe driv-
ing practices and switch the high beams
and low beam manually when necessary.
•The high beam or low beam may not
switch automatically under the follow-
ing conditions. Switch the high beam
and low beam manually. – During bad weather (rain, fog, snow,
wind, etc.).
– When a light source similar to a head-
light or tail light is in the vicinity of
the vehicle.
– When the headlights of the oncoming
vehicle or the leading vehicle are
turned off, when the color of the light
is affected due to foreign materials
on the lights, or when the light beam
is out of position.
– When there is a sudden, continuous
change in brightness.
– When driving on a road that passes
over rolling hills, or a road that has
level differences.
– When driving on a road with many
curves.
NSD594NDS595
2-68Instruments and controls

indicator light in the combination meter also
lights up.
If you are driving at speeds below approxi-
mately 28 MPH (45 km/h) or other road
users are detected or the roads are ad-
equately lit The high beam headlights are
switched off automatically. The
indica-
tor light in the combination meter goes out.
The
indicator light in the vehicle infor-
mation display remains lit.
To deactivate:
Move the combination switch back to its nor-
mal position The
indicator light in the
vehicle information display goes out.
HEADLIGHTS MISTED UP ON
THE INSIDE
Certain climatic and physical conditions may
cause moisture to form in the headlight. This
moisture does not affect the functionality of
the headlight.
INSTRUMENT BRIGHTNESS
CONTROL
The light sensor in the combination meter
automatically controls the brightness of the
instrument panel
In daylight, the displays in the combination
meter are not illuminated
The lighting in the combination meter, dis-
plays and controls in the vehicle interior can
be adjusted using the brightness control
knob.
The brightness control knob
1is located
behind the steering wheel.
Turn the brightness control knob clockwise or
counterclockwise. If the light switch is set to
orthe brightness is dependent
upon the brightness of the ambient light.
FRONT FOG LIGHTS
In conditions where visibility is poor due to
fog, snow or rain, the fog lights improve vis-
ibility as well as making it easier for other
road users to see you. They can be operated
together with the side lights or together with
the side lights and low beam headlights.
To switch on the fog lights:
•Turn the ignition switch to the ON position
or start the engine.
•Turn the light switch toor .
•Press thebutton. The greenindicator light in the combination meter
lights up
NIC2615NIC2699
FOG LIGHT SWITCH (IF SO
EQUIPPED)
2-70Instruments and controls