INFINITI QX4 2001 Factory Service Manual

3 CHECK POWER SOURCE AND DROPPING RESISTOR CIRCUIT
1. Turn ignition switch to ªOFFº position.
2. Disconnect TCM harness connector.
3. Check resistance between terminal 6 and TCM harness connector terminal 2.
SAT522J
Is resistance approx. 11.2 - 12.8W?
Ye s©GO TO 5.
No©GO TO 4.
4 DETECT MALFUNCTIONING ITEM
Check the following items:
IDropping resistor
Refer to ªComponent Inspectionº, AT-167.
IHarness for short or open between TCM terminal 2 and terminal cord assembly (Main harness)
OK or NG
OK©GO TO 5.
NG©Repair or replace damaged parts.
5 CHECK POWER SOURCE CIRCUIT
1. Turn ignition switch to ªOFFº position.
2. Check continuity between terminal 6 and TCM harness connector terminal 1. Refer to wiring diagram Ð AT Ð LPSV.
Continuity should exist.
If OK, check harness for short to ground or to power.
3. Reinstall any part removed.
Ye s©GO TO 6.
No©Repair or replace harness between TCM terminal 1 and terminal cord assembly.
6 CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-163.
OK or NG
OK©INSPECTION END
NG©GO TO 7.
DTC P0745 LINE PRESSURE SOLENOID VALVE
Diagnostic Procedure (Cont'd)
AT-166

7 CHECK TCM INSPECTION
1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK©INSPECTION END
NG©Repair or replace damaged parts.
SAT657I
Component InspectionNBAT0059LINE PRESSURE SOLENOID VALVENBAT0059S01IFor removal, refer to AT-273.
Resistance CheckNBAT0059S0101ICheck resistance between terminal 6 and ground.
Solenoid valve Terminal No. Resistance (Approx.)
Line pressure solenoid valve 6 Ground 2.5 - 5W
SAT658I
Operation CheckNBAT0059S0102ICheck solenoid valve by listening for its operating sound while
applying battery voltage to the terminal 6 and ground.
SAT848BD
DROPPING RESISTORNBAT0059S02ICheck resistance between two terminals.
Resistance: 11.2 - 12.8W
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0745 LINE PRESSURE SOLENOID VALVE
Diagnostic Procedure (Cont'd)
AT-167

SAT341H
DescriptionNBAT0060Shift solenoid valves A and B are turned ªONº or ªOFFº by the TCM
in response to signals sent from the PNP switch, vehicle speed and
throttle position sensors. Gears will then be shifted to the optimum
position.
Gear position1234
Shift solenoid valve A ON (Closed) OFF (Open) OFF (Open) ON (Closed)
Shift solenoid valve B ON (Closed) ON (Closed) OFF (Open) OFF (Open)
TCM TERMINALS AND REFERENCE VALUENBAT0060S02Remarks: Specification data are reference values.
Terminal
No.Wire color Item ConditionJudgement
standard
(Approx.)
11 L/WShift solenoid
valve A
When shift solenoid valve A operates.
(When driving in ªD
1ºorªD4º.)Battery volt-
age
When shift solenoid valve A does not operate.
(When driving in ªD
2ºorªD3º.)0V
ON BOARD DIAGNOSIS LOGICNBAT0060S03
Diagnostic trouble code Malfunction is detected when ... Check item (Possible cause)
: SFT SOL A/CIRC TCM detects an improper voltage drop
when it tires to operate the solenoid
valve.IHarness or connectors
(The solenoid circuit is open or shorted.)
IShift solenoid valve A
: P0750
SAT014K
SAT020K
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
NBAT0060S01CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If ªDIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DUREº has been previously conducted, always turn ignition
switch ªOFFº and wait at least 5 seconds before conducting
the next test.
After the repair, perform the following procedure to confirm the
malfunction is eliminated.
With CONSULT-II
1) Turn ignition switch ªONº and select ªDATA MONITORº mode
for ªENGINEº with CONSULT-II.
2) Start engine.
3) Drive vehicle in ªDº position and allow the transmission to shift
ª1º,ª2º (ªGEARº).
With GST
Follow the procedure ªWith CONSULT-IIº.
DTC P0750 SHIFT SOLENOID VALVE A
Description
AT-168

Wiring Diagram Ð AT Ð SSV/ANBAT0197
MAT738A
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0750 SHIFT SOLENOID VALVE A
Wiring Diagram Ð AT Ð SSV/A
AT-169

Diagnostic ProcedureNBAT0061
1 CHECK VALVE RESISTANCE
1. Turn ignition switch to ªOFFº position.
2. Disconnect terminal cord assembly connector on the right side of transfer assembly.
3. Check resistance between terminal 3 and ground.
SAT164J
Is resistance approx. 20 - 40W?
Ye s©GO TO 3.
No©GO TO 2.
2 CHECK VALVE OPERATION
1. Remove control valve assembly.
Refer to AT-273.
2. Check the following items:
IShift solenoid valve A
Refer to ªComponent Inspectionº, AT-171.
IHarness of terminal cord assembly for short or open
OK or NG
OK©GO TO 3.
NG©Repair or replace damaged parts.
3 CHECK POWER SOURCE CIRCUIT
1. Turn ignition switch to ªOFFº position.
2. Disconnect TCM harness connector.
3. Check resistance between terminal 3 and TCM harness connector terminal 11. Refer to wiring diagram Ð AT Ð
SSV/A.
Continuity should exist.
If OK, check harness for short to ground and short to power.
4. Reinstall any part removed.
OK or NG
OK©GO TO 4.
NG©Repair open circuit or short to ground or short to power in harness or connectors.
4 CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-168.
OK or NG
OK©INSPECTION END
NG©GO TO 5.
DTC P0750 SHIFT SOLENOID VALVE A
Diagnostic Procedure
AT-170

5 CHECK TCM INSPECTION
1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK©INSPECTION END
NG©Repair or replace damaged parts.
SAT654I
Component InspectionNBAT0062SHIFT SOLENOID VALVE ANBAT0062S01IFor removal, refer to AT-273.
Resistance CheckNBAT0062S0101ICheck resistance between terminal 3 and ground.
Solenoid valve Terminal No. Resistance (Approx.)
Shift solenoid valve A 3 Ground 20 - 40W
SAT653I
Operation CheckNBAT0062S0102ICheck solenoid valve by listening for its operating sound while
applying battery voltage to the terminal 3 and ground.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0750 SHIFT SOLENOID VALVE A
Diagnostic Procedure (Cont'd)
AT-171

SAT341H
DescriptionNBAT0063Shift solenoid valves A and B are turned ªONº or ªOFFº by the TCM
in response to signals sent from the PNP switch, vehicle speed and
throttle position sensors. Gears will then be shifted to the optimum
position.
Gear position1234
Shift solenoid valve A ON (Closed) OFF (Open) OFF (Open) ON (Closed)
Shift solenoid valve B ON (Closed) ON (Closed) OFF (Open) OFF (Open)
TCM TERMINALS AND REFERENCE VALUENBAT0063S02Remarks: Specification data are reference values.
Terminal
No.Wire color Item ConditionJudgement
standard
(Approx.)
12 L/RShift solenoid
valve B
When shift solenoid valve B operates.
(When driving in ªD
1ºorªD2º.)Battery volt-
age
When shift solenoid valve B does not operate.
(When driving in ªD
3ºorªD4º.)0V
ON BOARD DIAGNOSIS LOGICNBAT0063S03
Diagnostic trouble code Malfunction is detected when ... Check item (Possible cause)
: SFT SOL B/CIRC TCM detects an improper voltage drop
when it tires to operate the solenoid
valve.IHarness or connectors
(The solenoid circuit is open or shorted.)
IShift solenoid valve B
: P0755
SAT014K
SAT020K
DIAGNOSTIC TROUBLE CODE (DTC) CONFIRMATION
PROCEDURE
NBAT0063S01CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If ªDIAGNOSTIC TROUBLE CODE CONFIRMATION PROCE-
DUREº has been previously conducted, always turn ignition
switch ªOFFº and wait at least 5 seconds before conducting
the next test.
After the repair, perform the following procedure to confirm the
malfunction is eliminated.
With CONSULT-II
1) Turn ignition switch ªONº and select ªDATA MONITORº mode
for ªENGINEº with CONSULT-II.
2) Drive vehicle in ªDº position and allow the transmission to shift
1,2,3 (ªGEARº).
With GST
Follow the procedure ªWith CONSULT-IIº.
DTC P0755 SHIFT SOLENOID VALVE B
Description
AT-172

Wiring Diagram Ð AT Ð SSV/BNBAT0198
MAT739A
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0755 SHIFT SOLENOID VALVE B
Wiring Diagram Ð AT Ð SSV/B
AT-173

Diagnostic ProcedureNBAT0064
1 CHECK VALVE RESISTANCE
1. Turn ignition switch to ªOFFº position.
2. Disconnect terminal cord assembly connector on the right side of transfer assembly.
3. Check resistance between terminal 2 and ground.
SAT166J
Is resistance approx. 20 - 40W?
Ye s©GO TO 3.
No©GO TO 2.
2 CHECK VALVE OPERATION
1. Remove control valve assembly.
Refer to AT-273.
2. Check the following items:
IShift solenoid valve B
Refer to ªComponent Inspectionº, AT-175.
IHarness of terminal cord assembly for short or open
OK or NG
OK©GO TO 3.
NG©Repair or replace damaged parts.
3 CHECK POWER SOURCE CIRCUIT
1. Turn ignition switch to ªOFFº position.
2. Disconnect TCM harness connector.
3. Check resistance between terminal 2 and TCM harness connector terminal 12. Refer to wiring diagram Ð AT Ð
SSV/B.
Continuity should exist.
If OK, check harness for short to ground and short to power.
4. Reinstall any part removed.
Is resistance approx. 0W?
Ye s©GO TO 4.
No©Repair open circuit or short to ground or short to power in harness or connectors.
4 CHECK DTC
Perform Diagnostic Trouble Code (DTC) confirmation procedure, AT-172.
OK or NG
OK©INSPECTION END
NG©GO TO 5.
DTC P0755 SHIFT SOLENOID VALVE B
Diagnostic Procedure
AT-174

5 CHECK TCM INSPECTION
1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK©INSPECTION END
NG©Repair or replace damaged parts.
SAT651I
Component InspectionNBAT0065SHIFT SOLENOID VALVE BNBAT0065S01IFor removal, refer to AT-273.
Resistance CheckNBAT0065S0101ICheck resistance between terminal 2 and ground.
Solenoid valve Terminal No. Resistance (Approx.)
Shift solenoid valve B 2 Ground 20 - 40W
SAT650I
Operation CheckNBAT0065S0102ICheck solenoid valve by listening for its operating sound while
applying battery voltage to the terminal 2 and ground.
GI
MA
EM
LC
EC
FE
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
DTC P0755 SHIFT SOLENOID VALVE B
Diagnostic Procedure (Cont'd)
AT-175