fuel pressure INFINITI QX4 2005 Factory Owners Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: QX4, Model: INFINITI QX4 2005Pages: 3419, PDF Size: 80.18 MB
Page 2073 of 3419
FL-8Revision: October 2005
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
2005 QX56
11. Remove the lock ring using Tool.
12. Remove the fuel level sensor, fuel filter, and fuel pump assem-
bly.
CAUTION:
Do not bend the float arm during removal.
Avoid impacts such as dropping when handling the com-
ponents.
INSTALLATION
Installation is in the reverse order of removal.
Connect the quick connector as follows:
–Check the connection for any damage or foreign materials.
–Align the connector with the pipe, then insert the connector straight into the pipe until a click is heard.
–After connecting the quick connector, make sure that the con-
nection is secure by checking as follows:
–Pull the tube and the connector to make sure they are securely
connected.
–Visually inspect the connector to make sure the two retainer tabs
are securely connected.
INSPECTION AFTER INSTALLATION
1. Turn the ignition switch ON but do not start engine, then check the fuel pipes and hose connections for
leaks while applying fuel pressure to the system.
2. Start the engine and rev it above idle speed, then check that there are no fuel leaks at any of the fuel pipe
and hose connections.Tool number : — (J-46536)
LBIA0389E
PBIC1653E
Page 2075 of 3419
FL-10Revision: October 2005
FUEL TANK
2005 QX56
REMOVAL
WAR NIN G:
Follow the “General Precautions” before working on the fuel system. Refer to FL-3, "
General Precau-
tions" .
1. Drain the fuel from the fuel tank, if necessary.
Position the vehicle so it is level.
2. Remove the fuel filler cap to release the pressure from inside the fuel tank.
3. Check the fuel level on level gauge. If the fuel gauge indicates
more than the level as shown (full or almost full), drain the fuel
from the fuel tank until the fuel gauge indicates the level as
shown, or less.
If the fuel pump does not operate, use the following procedure
to drain the fuel to the specified level after disconnecting the
fuel filler hose from the fuel filler pipe.
a. Insert a suitable hose of less than 15 mm (0.59 in) diameter into
the fuel filler pipe through the fuel filler opening to drain the fuel
from fuel filler pipe.
b. Insert a suitable hose into the fuel tank through the fuel filler
hose to drain the fuel from the fuel tank.
As a guide, the fuel level reaches the fuel gauge position as shown, or less, when approximately 14
liters (3 3/4 US gal, 3 1/8 Imp gal) of fuel are drained from the fuel tank.
4. Remove the LH rear wheel and tire. Refer to WT-7, "
Rotation" .
5. Remove the four clips and remove the rear fender protector, front.
6. Disconnect the fuel filler hose from the fuel filler pipe and dis-
connect the vent hose quick connector.
7. Release the fuel pressure from the fuel lines. Refer to EC-93, "
FUEL PRESSURE RELEASE" .
8. Remove the second row LH rear seat and the third row rear seat. Refer to SE-104, "
REAR SEAT" .
9. Remove the second and third row rear seat belt buckles mounted on the floor. Refer to SB-3, "
SEAT
BELTS" .
10. Remove the LH center pillar trim, the LH rear trim panel, and the LH rear side door kick plate and weather
stripping. Refer to EI-35, "
BODY SIDE TRIM" .
11. Remove the second row rear center console and base. Refer to EI-37, "
FLOOR TRIM" .
12. Reposition the floor carpet out of the way to access the inspection hole cover, located under the center LH
rear seat.
10. Fuel filler hose 11. Fuel filler pipe 12. Fuel filler cup
13. Fuel filler hose grommet 14. Fuel filler cap 15. Fuel tank shield
WBIA0390E
LBIA0386E
Page 2078 of 3419
FUEL TANK
FL-13
C
D
E
F
G
H
I
J
K
L
MA
FL
Revision: October 20052005 QX56
19. Remove the fuel tank strap bolts while supporting the fuel tank
with a suitable lift jack.
20. Disconnect the EVAP hose from the molded clip in the top of the fuel tank while lowering the fuel tank.
21. Lower the fuel tank using a suitable lift jack and remove it.
22. If necessary, remove the lock ring using Tool.
23. If necessary, remove the fuel level sensor, fuel filter, and fuel
pump assembly.
CAUTION:
Do not bend the float arm during removal.
Avoid impacts such as dropping when handling the com-
ponents.
INSTALLATION
Installation is in the reverse order of removal.
Connect the quick connector as follows:
–Check the connection for any damage or foreign materials.
–Align the connector with the pipe, then insert the connector straight into the pipe until a click is heard.
–After connecting the quick connector, make sure that the con-
nection is secure by checking as follows:
–Pull the tube and the connector to make sure they are securely
connected.
–Visually inspect the connector to make sure the two retainer tabs
are securely connected.
INSPECTION AFTER INSTALLATION
1. Turn the ignition switch ON but do not start engine, then check the fuel pipe and hose connections for
leaks while applying fuel pressure.
2. Start the engine and rev it above idle, then check that there are no fuel leaks at any of the fuel pipe and
hose connections.
LBIA0387E
Tool number : — (J-46536)
LBIA0389E
PBIC1653E
Page 2085 of 3419
FSU-6
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
ON-VEHICLE SERVICEPFP:00000
Front Suspension PartsEES001GI
Check front suspension parts for excessive play, cracks, wear and
other damage.
Shake each front wheel to check for excessive play.
If looseness is noted, inspect wheel bearing end play, then
check ball joint end play. Refer to FAX-5, "
WHEEL BEARING
INSPECTION" and FSU-15, "Inspection" .
Make sure that the cotter pin is inserted (4x4 only).
Retighten all nuts and bolts to the specified torque.
Check shock absorber for oil leakage and other damage.
Check suspension ball joint for grease leakage and ball joint
dust cover for cracks and other damage.
Front Wheel AlignmentEES001GJ
PRELIMINARY INSPECTION
WAR NIN G:
Always adjust the alignment with the vehicle on a flat surface.
NOTE:
If alignment is out of specification, inspect and replace any damaged or worn suspension parts before making
any adjustments.
1. Check and adjust the wheel alignment with the vehicle under unladen conditions. “Unladen conditions”
means that the fuel, coolant, and lubricant are full; and that the spare tire, jack, hand tools and mats are in
their designated positions.
2. Check the tires for incorrect air pressure and excessive wear.
3. Check the wheels for run out and damage. Refer to WT-5, "
Inspection" .
4. Check the wheel bearing axial end play. Refer to FAX-5, "
WHEEL BEARING INSPECTION" .
5. Check the shock absorbers for leaks or damage.
6. Check each mounting point of the suspension components for any excessive looseness or damage.
7. Check each link, arm, and the rear suspension member for any damage.
8. Check the vehicle height. Refer to FSU-21, "
Wheelarch Height (Unladen*1 )" .
Verify the level using Consult-II memory register 1103 and set to 0 ± 10 mm (0 ± 0.39 in) as necessary.
GENERAL INFORMATION AND RECOMMENDATIONS
1. A Four-Wheel Thrust Alignment should be performed.
This type of alignment is recommended for any NISSAN vehicle.
The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel
is centered.
The alignment machine itself should be capable of accepting any NISSAN vehicle.
The alignment machine should be checked to ensure that it is level.
2. Make sure the alignment machine is properly calibrated.
Your alignment machine should be regularly calibrated in order to give correct information.Suspension component torques : Refer to FSU-5,
"Components" .SM A52 5A
SFA392B
Page 2107 of 3419
GI-6
PRECAUTIONS
Revision: October 20052005 QX56
Precautions for Multiport Fuel Injection System or Engine Control SystemEAS001FA
Before connecting or disconnecting any harness connector for
the multiport fuel injection system or ECM:
Turn ignition switch to “OFF” position.
Disconnect negative battery terminal.
Otherwise, there may be damage to ECM.
Before disconnecting pressurized fuel line from fuel pump to
injectors, be sure to release fuel pressure.
Be careful not to jar components such as ECM and mass air
flow sensor.
Precautions for HosesEAS001FB
HOSE REMOVAL AND INSTALLATION
To prevent damage to rubber hose, do not pry off rubber hose
with tapered tool or screwdriver.
To reinstall the rubber hose securely, make sure of hose inser-
tion length and clamp orientation. (If tube is equipped with hose
stopper, insert rubber hose into tube until it butts up against
hose stopper.)
HOSE CLAMPING
If old rubber hose is re-used, install hose clamp in its original
position (at the indentation where the old clamp was). If there is
a trace of tube bulging left on the old rubber hose, align rubber
hose at that position.
Discard old clamps; replace with new ones.
SGI787
SM A01 9D
SM A02 0D
SM A02 1D
Page 2151 of 3419
GI-50
TERMINOLOGY
Revision: October 20052005 QX56
TERMINOLOGYPFP:00011
SAE J1930 Terminology List EAS001G6
All emission related terms used in this publication in accordance with SAE J1930 are listed. Accordingly, new
terms, new acronyms/abbreviations and old terms are listed in the following chart.
NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM
Air cleaner ACL Air cleaner
Barometric pressure BARO ***
Barometric pressure sensor-BCDD BAROS-BCDD BCDD
Camshaft position CMP ***
Camshaft position sensor CMPS Crank angle sensor
Canister *** Canister
Carburetor CARB Carburetor
Charge air cooler CAC Intercooler
Closed loop CL Closed loop
Closed throttle position switch CTP switch Idle switch
Clutch pedal position switch CPP switch Clutch switch
Continuous fuel injection system CFI system ***
Continuous trap oxidizer system CTOX system ***
Crankshaft position CKP ***
Crankshaft position sensor CKPS ***
Data link connector DLC ***
Data link connector for CONSULT-II DLC for CONSULT-II Diagnostic connector for CONSULT-II
Diagnostic test mode DTM Diagnostic mode
Diagnostic test mode selector DTM selector Diagnostic mode selector
Diagnostic test mode I DTM I Mode I
Diagnostic test mode II DTM II Mode II
Diagnostic trouble code DTC Malfunction code
Direct fuel injection system DFI system ***
Distributor ignition system DI system Ignition timing control
Early fuel evaporation-mixture heater EFE-mixture heater Mixture heater
Early fuel evaporation system EFE system Mixture heater control
Electrically erasable programmable read
only memoryEEPROM ***
Electronic ignition system EI system Ignition timing control
Engine control EC ***
Engine control module ECM ECCS control unit
Engine coolant temperature ECT Engine temperature
Engine coolant temperature sensor ECTS Engine temperature sensor
Engine modification EM ***
Engine speed RPM Engine speed
Erasable programmable read only memory EPROM ***
Evaporative emission canister EVAP canister Canister
Evaporative emission system EVAP system Canister control solenoid valve
Exhaust gas recirculation valve EGR valve EGR valve
Page 2152 of 3419
TERMINOLOGY
GI-51
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: October 20052005 QX56
Exhaust gas recirculation control-BPT
valveEGRC-BPT valve BPT valve
Exhaust gas recirculation control-solenoid
valveEGRC-solenoid valve EGR control solenoid valve
Exhaust gas recirculation temperature sen-
sor
EGRT sensor Exhaust gas temperature sensor
EGR temperature sensor
Flash electrically erasable programmable
read only memoryFEEPROM ***
Flash erasable programmable read only
memoryFEPROM ***
Flexible fuel sensor FFS ***
Flexible fuel system FF system ***
Fuel pressure regulator *** Pressure regulator
Fuel pressure regulator control solenoid
valve*** PRVR control solenoid valve
Fuel trim FT ***
Heated Oxygen sensor HO2S Exhaust gas sensor
Idle air control system IAC system Idle speed control
Idle air control valve-air regulator IACV-air regulator Air regulator
Idle air control valve-auxiliary air control
valveIACV-AAC valve Auxiliary air control (AAC) valve
Idle air control valve-FICD solenoid valve IACV-FICD solenoid valve FICD solenoid valve
Idle air control valve-idle up control sole-
noid valveIACV-idle up control solenoid valve Idle up control solenoid valve
Idle speed control-FI pot ISC-FI pot FI pot
Idle speed control system ISC system ***
Ignition control IC ***
Ignition control module ICM ***
Indirect fuel injection system IFI system ***
Intake air IA Air
Intake air temperature sensor IAT sensor Air temperature sensor
Knock *** Detonation
Knock sensor KS Detonation sensor
Malfunction indicator lamp MIL Check engine light
Manifold absolute pressure MAP ***
Manifold absolute pressure sensor MAPS ***
Manifold differential pressure MDP ***
Manifold differential pressure sensor MDPS ***
Manifold surface temperature MST ***
Manifold surface temperature sensor MSTS ***
Manifold vacuum zone MVZ ***
Manifold vacuum zone sensor MVZS ***
Mass air flow sensor MAFS Air flow meter
Mixture control solenoid valve MC solenoid valve Air-fuel ratio control solenoid valve
Multiport fuel injection System MFI system Fuel injection controlNEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM
Page 2257 of 3419
IDX-4
ALPHABETICAL INDEX
Drive chain (Transfer) ......................... TF-147, TF-174
Drive pinion diff. inspection ............................. RFD-13
Drive pinion height .......................................... RFD-18
Drive shaft (rear) ............................................... RAX-7
Driver air bag .................................................. SRS-46
DTC work support ............................................ EC-136
DTRL - Wiring diagram ....................................... LT-37
Duct and grilles .............................................. ATC-170
DVD Player ........................................................ AV-60
E
ECM input/output signal ..................... EC-117
, EC-141
ECM power supply ............................. EC-157, EC-393
ECM relay ........................................................ EC-157
ECM/PW - Wiring diagram ............................... EC-394
ECTS - Wiring diagram .................................... EC-197
Electric sunroof .................................................. RF-10
Electric throttle control actuator ......... EC-397, EC-399
Electrical load signal circuit .............................. EC-648
Electrical units location ...................................... PG-63
Electronic ignition (EI) system ........................... EC-26
Engine control circuit diagram ......................... EC-115
Engine control component parts location ......... EC-108
Engine control module (ECM) .......................... EC-383
Engine control system diagram ......................... EC-23
Engine coolant .................................................. CO-10
Engine coolant temperature sensor (ECTS) ... EC-195,
EC-208
Engine fail-safe system .................................... EC-103
Engine oil ............................................................. LU-7
Engine oil filter replacement ............................. MA-17
Engine oil precautions .......................................... GI-7
Engine oil replacement ..................................... MA-17
Engine removal ................................................. EM-69
Engine room cover ............................................ EM-11
Engine serial number .......................................... GI-48
ETC1 - Wiring diagram .................................... EC-400
ETC2 - Wiring diagram .................................... EC-407
ETC3 - Wiring diagram .................................... EC-411
EVAP canister .................................................... EC-35
EVAP canister purge volume control solenoid valve ....
EC-318
, EC-531
EVAP canister vent control valve ....... EC-325, EC-539
EVAP control system (small leak) diagnosis .. EC-309,
EC-349
, EC-357
EVAP control system pressure sensor .... EC-332, EC-
335, EC-341
EVAP control system purge flow monitoring diagnosis
EC-304
EVAP vapor lines inspection ............................. MA-20
Evaporative emission (EVAP) system ............... EC-32
Evaporator ..................................................... ATC-186
Exhaust manifold .............................................. EM-19
Exhaust system ................................................... EX-3
Exhaust system inspection .................................. EX-3
Expansion valve ............................................. ATC-188
F
F/FOG - Wiring diagram ..................................... LT-71
F/PUMP - Wiring diagram ............................... EC-638
Final drive pre-inspection .................. FFD-14, RFD-13
Final drive removal and installation ... FFD-11, RFD-10
Flow charts .......................................................... GI-27
Fluid temperature sensor (A/T) ........................ AT-126
Fluids ................................................................ MA-11
Fluorescent leak detector .............................. ATC-189
Fog lamp, front ................................................... LT-69
Foot lamp ......................................................... LT-130
Freeze frame data ............................... EC-54, EC-130
Front brake solenoid valve ................. AT-144, AT-146
Front bumper ...................................................... EI-13
Front case (Transfer) .......................... TF-147, TF-174
Front combination lamp removal and installation LT-32
Front door ............................. BL-128, BL-131, GW-68
Front Door Trim ................................................... EI-32
Front drive shaft (Transfer) ................. TF-147, TF-174
Front fog lamp .................................................... LT-69
Front passenger air bag .................................. SRS-51
Front seat ........................................................... SE-97
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ............... SRS-3, SRS-58
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTTS - Wiring diagram ...................... EC-255, EC-260
Fuel cut control (at no load high engine speed) EC-27
Fuel filter replacement ......................................... FL-5
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) .......... EC-236, EC-245
Fuel injection system (Bank 2) .......... EC-236, EC-245
Fuel injector and fuel tube ................................. EM-29
Fuel level sensor ................. EC-366, EC-368, EC-370
Fuel line inspection .............................................. FL-3
Fuel pressure check .......................................... EC-93
Fuel pressure release ....................................... EC-93
Fuel pump ....................................................... EC-637
Fuel pump and gauge .......................................... FL-5
Fuel system .......................................................... FL-3
Fuel tank .............................................................. FL-9
Fuel tank temperature sensor ........... EC-253, EC-259
Fuel tank vacuum relief valve ........................... EC-35
FUELB1 - Wiring diagram ................. EC-238, EC-247
FUELB2 - Wiring diagram ................. EC-239, EC-248
Fuse ...................................................... PG-66, PG-77
Fuse and fusible link box .................................. PG-77
Fuse block ......................................................... PG-76
Fusible link ............................................ PG-66, PG-77
G
Garage jack and safety stand ............................. GI-40
Gauges ................................................................. DI-5
Generator .......................................................... SC-17
Generic scan tool (GST) ................................. EC-139
Glass ...................................... GW-11, GW-68, GW-71
Glove box lamp ................................................ LT-153
Page 2259 of 3419
IDX-6
ALPHABETICAL INDEX
M
MAFS - Wiring diagram ..................... EC-177
, EC-185
Magnet clutch ............................... ATC-115, ATC-180
MAIN - Wiring diagram .................................... EC-157
Main oil pump (Transfer) ..................... TF-152, TF-165
Mainshaft (Transfer) ........................... TF-152, TF-165
Maintenance (engine)Schedule 1 ....................... MA-7
Maintenance (engine)Schedule 2 ....................... MA-9
Major overhaul (Final drive) .............. FFD-13, RFD-14
Major overhaul (Transfer) ................................ TF-144
Malfunction indicator lamp (MIL) ........................ EC-64
Map lamp .......................................................... LT-130
Mass air flow sensor (MAFS) ............. EC-174, EC-183
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ....................... EC-667
MIL/DL - Wiring diagram .................................. EC-667
Misfire .............................................................. EC-271
Mode door control linkage adjustment ............. ATC-66
Mode door motor ............................ ATC-64, ATC-165
Model variation ................................................... GI-46
Multiport fuel injection (MFI) system .................. EC-24
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ............................................................... BL-44
N
NATS - Wiring diagram .................................... BL-140
NAVI - Wiring diagram ....................................... AV-79
NAVI Control Unit ............................................ AV-157
Neutral-4LO switch ............................................ TF-62
NVH troubleshooting (AX) ................................. FAX-4
NVH troubleshooting (EM) .................................. EM-9
NVH troubleshooting (Final drive) ..................... RFD-5
NVH troubleshooting (Propeller shaft) ................. PR-3
NVH troubleshooting (RAX) .............................. RAX-4
NVH troubleshooting (RSU) .............................. RSU-5
NVH troubleshooting (ST) .................................... PS-5
NVH troubleshooting (Transfer) ......................... TF-10
NVH troubleshooting (WT)NVH troubleshooting (WT) .
WT-4
NVIS (Nissan vehicle immobilizer system) precautions
GI-3
O
O2H2B1 - Wiring diagram ................................ EC-168
O2H2B2 - Wiring diagram ................................ EC-170
O2S2B1 - Wiring diagram .. EC-218, EC-228, EC-418,
EC-429
O2S2B2 - Wiring diagram .. EC-220, EC-230, EC-420,
EC-431
Oil cooler (engine) ............................................. LU-11
Oil filter ............................................................... LU-10
Oil filter (Transfer) ............................................ TF-141
Oil pan (engine) ................................................ EM-22
Oil pressure (engine) ........................................... LU-7
Oil pressure relief valve (engine) ......................... LU-5
Oil pump (engine) .............................................. LU-13
Oil seal replacement (engine) ........................... EM-55
Oil seal replacement (front of final drive) FFD-7, RFD-6
Oil seal replacement (side of final drive) FFD-9, RFD-8
On board diagnostic system ............................. EC-48
ORVR (On-board Refueling Vapor Recovery) .. EC-39
Overheat ......................................................... EC-440
P
P/SCKT - Wiring diagram ................................. WW-56
Pantograph jack .................................................. GI-40
Park/Neutral position switch ............................ EC-581
Park/neutral position switch (A/T) .................... AT-104
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................ EC-45
Periodic maintenance ......................................... MA-7
Personal lamp .................................................. LT-130
PGC/V - Wiring diagram ................... EC-320, EC-533
PHASE - Wiring diagram ................................ EC-291
Pinion bearing preload diff. ............................. RFD-22
Piston pin inspection ......................................... EM-89
Piston ring inspection ........................................ EM-90
Piston to bore clearance ................................... EM-94
Planetary carrier (Transfer) ................. TF-147, TF-174
PNP/SW - Wiring diagram .............................. EC-583
POS - Wiring diagram ..................................... EC-286
POWER - Wiring diagram ................................... PG-6
Power door lock ................................................. BL-16
Power seat ......................................................... SE-89
Power steering fluid level .................................. MA-29
Power steering gear ........................................... PS-15
Power steering oil pump .................................... PS-26
Power steering pressure (PSP) sensor ........... EC-378
Power steering system bleeding .......................... PS-6
Power supply routing .......................................... PG-4
Power window .................................................. GW-15
PRE/SE - Wiring diagram ................. EC-337, EC-343
Precautions (General) ........................................... GI-4
Precautions in repairing high strength steel ..... BL-190
Pressure switch 1 ............................... AT-146, AT-160
Pressure switch 2 ............................................. AT-158
Pressure switch 3 ............................... AT-142, AT-162
Pressure switch 5 ............................... AT-150, AT-164
Pressure switch 6 ............................... AT-154, AT-166
Pressure test (A/T) ............................................. AT-51
Propeller shaft ........................................... PR-4, PR-8
Propeller shaft inspection .................................. MA-25
Propeller shaft on vehicle service ....................... PR-8
Propeller shaft vibration ............................ PR-4, PR-8
PS/SEN - Wiring diagram ............................... EC-379
R
R/VIEW - Wiring diagram .................................... DI-74
Radiator ............................................................ CO-12
Rear Audio Remote Control Unit ....................... AV-47
Rear axle ........................................................... RAX-5
Page 2286 of 3419
![INFINITI QX4 2005 Factory Owners Manual CAN COMMUNICATION
LAN-7
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: October 20052005 QX56
Fuel level sensor signal R T
Fuel level low warning signal T R
ASCD SET lamp signal T R
ASCD CRUISE lamp signal](/img/42/57035/w960_57035-2285.png "INFINITI QX4 2005 Factory Owners Manual CAN COMMUNICATION
LAN-7
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: October 20052005 QX56
Fuel level sensor signal R T
Fuel level low warning signal T R
ASCD SET lamp signal T R
ASCD CRUISE lamp signal")
CAN COMMUNICATION
LAN-7
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: October 20052005 QX56
Fuel level sensor signal R T
Fuel level low warning signal T R
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp signal T R
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch signal T R R
Rear window defogger control signal R R R T
Hood switch signalRT
Theft warning horn request signal T R
Horn chirp signalTR
Steering angle sensor signalTR
ABS warning lamp signal R T
VDC OFF indicator lamp signal R T
SLIP indicator lamp signal R T
Brake warning lamp signal R T
System setting signalRT
TR
Distance to empty signal T R
ASCD operation signal T R
ASCD OD cancel request T R
A/T CHECK indicator lamp signal T R
A/T position indicator lamp signal T R
Tire pressure signal R T
Tire pressure data signal R T
1st position switch signal R T
4th position switch signal R T
Tow mode switch signal R T
A/T fluid temperature sensor signal T RSignals ECM TCMDriver
seat
con-
trol
unitCom-
bina-
tion
meterDis-
play
con-
trol
unitBCMStee r-
ing
angle
sensorFront
air
control ABS
actua-
tor and
elec-
tric unit
(con-
trol
unit)IPDM
E/R