engine oil INFINITI QX4 2005 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: QX4, Model: INFINITI QX4 2005Pages: 3419, PDF Size: 80.18 MB
Page 2106 of 3419
PRECAUTIONS
GI-5
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: October 20052005 QX56
Use approved bonding agent, sealants or their equivalents when required.
Use hand tools, power tools (disassembly only) and recom-
mended special tools where specified for safe and efficient ser-
vice repairs.
When repairing the fuel, oil, water, vacuum or exhaust systems,
check all affected lines for leaks.
Before servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate cov-
ers.
Take caution that keys, buckles or buttons do not scratch paint.
WA RN ING:
To prevent ECM from storing the diagnostic trouble codes, do not carelessly disconnect the harness
connectors which are related to the engine control system and TCM (transmission control module)
system. The connectors should be disconnected only when working according to the WORK FLOW of
TROUBLE DIAGNOSES in EC and AT sections.
Precautions for Three Way CatalystEAS001F8
If a large amount of unburned fuel flows into the catalyst, the catalyst temperature will be excessively high. To
prevent this, follow the instructions.
Use unleaded gasoline only. Leaded gasoline will seriously damage the three way catalyst.
When checking for ignition spark or measuring engine compression, make tests quickly and only when
necessary.
Do not run engine when the fuel tank level is low, otherwise the engine may misfire, causing damage to
the catalyst.
Do not place the vehicle on flammable material. Keep flammable material off the exhaust pipe and the three
way catalyst.
Precautions for Fuel (Unleaded Regular Gasoline Recommended)EAS001XQ
Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research
octane number 91). E-85 fuel (85% fuel ethanol, 15% unleaded gasoline) may only be used in vehicles specif-
ically designed for E-85 fuel (i.e. Flexible Fuel Vehicle - FFV models.)
CAUTION:
Do not use leaded gasoline. Using leaded gasoline will damage the three way catalyst. Do not use E-85
fuel (85% fuel ethanol, 15% unleaded gasoline) unless the vehicle is specifically designed for E-85 fuel
(i.e. Flexible Fuel Vehicle - FFV Models). Using a fuel other than that specified could adversely affect
the emission control devices and systems, and could also affect the warranty coverage validity.
PBIC0190E
SGI234
Page 2108 of 3419
PRECAUTIONS
GI-7
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: October 20052005 QX56
After installing leaf spring clamps, apply force to them in the
direction of the arrow, tightening rubber hose equally all around.
Precautions for Engine OilsEAS001FC
Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin contact
with used oil.
If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.
HEALTH PROTECTION PRECAUTIONS
Avoid prolonged and repeated contact with oils, particularly used engine oils.
Wear protective clothing, including impervious gloves where practicable.
Do not put oily rags in pockets.
Avoid contaminating clothes, particularly underpants, with oil.
Heavily soiled clothing and oil-impregnated footwear should not be worn. Overalls must be cleaned regu-
larly.
First aid treatment should be obtained immediately for open cuts and wounds.
Use barrier creams, applying them before each work period, to help the removal of oil from the skin.
Wash with soap and water to ensure all oil is removed (skin cleansers and nail brushes will help). Prepa-
rations containing lanolin replace the natural skin oils which have been removed.
Do not use gasoline, kerosene, diesel fuel, gas oil, thinners or solvents for cleaning skin.
If skin disorders develop, obtain medical advice without delay.
Where practical, degrease components prior to handling.
Where there is a risk of eye contact, eye protection should be worn, for example, chemical goggles or face
shields; in addition an eye wash facility should be provided.
ENVIRONMENTAL PROTECTION PRECAUTIONS
Dispose of used oil and used oil filters through authorized waste disposal contractors to licensed waste dis-
posal sites, or to the waste oil reclamation trade. If in doubt, contact the local authority for advice on disposal
facilities.
It is illegal to pour used oil on to the ground, down sewers or drains, or into water sources.
The regulations concerning pollution vary between regions.
Precautions for Air ConditioningEAS001FD
Use an approved refrigerant recovery unit any time the air conditioning system must be discharged. Refer to
ATC-175, "
HFC-134a (R-134a) Service Procedure" for specific instructions.
SM A02 2D
Page 2256 of 3419
IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Body repair ....................................................... BL-160
Body sealing ..................................................... BL-168
Brake booster .................................................... BR-16
Brake fluid level ................................................. MA-28
Brake hydraulic line ........................................... BR-11
Brake inspection ................................................ MA-28
Brake lines and cables inspection ..................... MA-28
Brake master cylinder ....................................... BR-14
Brake switch ...................................... EC-569, EC-586
BRK/SW - Wiring diagram ............................... EC-587
Bulb specifications ........................................... LT-170
Bumper, front ...................................................... EI-13
Bumper, rear ....................................................... EI-15
C
Camshaft ........................................................... EM-43
Camshaft inspection .......................................... EM-46
Camshaft position sensor (PHASE) ................ EC-291
CAN - Wiring diagram EC-164, LAN-18, LAN-52, LAN-
92, LAN-128
CAN (Controller Area Network) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
CAN communication ... EC-31, EC-163, AT-95, TF-20,
TF-113
, BRC-10, SE-17, LAN-16, LAN-50, LAN-90,
LAN-126
Canister-See EVAP canister ............................. EC-35
Center case (Transfer) ....................... TF-152, TF-165
CHARGE - Wiring diagram ............................... SC-18
Charging system ............................................... SC-17
Chassis and body maintenance ........................ MA-21
Chassis and body maintenanceSchedule 1 ........ MA-8
Chassis and body maintenanceSchedule 2 ...... MA-10
CHIME - Wiring diagram ..................................... DI-44
Circuit breaker ................................................... PG-66
Clock ................................................................... DI-69
CLOCK - Wiring diagram .................................... DI-69
Closed loop control ........................................... EC-25
Closed loop control (Bank 1) ........................... EC-437
Closed loop control (Bank 2) ........................... EC-437
Clutch drum (Transfer) ....................... TF-152, TF-165
Clutch pressure switch (Transfer) ...... TF-152, TF-165
Coil spring (front) ............................................. FSU-10
Collision diagnosis .......................................... SRS-61
Combination lamp, front, removal and installation . LT-
32
Combination lamp, rear, removal and installation .. LT-
122
Combination meter ................................................ DI-5
Combination switch ............................................ LT-97
COMBSW - Wiring diagram ............................... LT-97
COMM - Wiring diagram ................................... AV-87
COMPAS - Wiring diagram ................................. DI-27
Compass ............................................................. DI-26
Component Location (auto A/C) ...................... ATC-39
Compressor clutch removal and installation . ATC-180
Compressor mounting ................................... ATC-179
Compressor precaution ................................... ATC-11
Compressor special service tool ..................... ATC-14
Condenser ..................................................... ATC-185
Connecting rod .................................................. EM-91
Connecting rod bearing clearance ..................... EM-91
Connecting rod bushing clearance .................... EM-91
Console box - See Instrument panel ................... IP-10
CONSULT for VDC ......................................... BRC-28
CONSULT general information ........................... GI-37
CONSULT-II for engine ................................... EC-126
Control units (terminal arrangement) ................. PG-71
Control valve (A/T) ............................................. AT-35
Control valve (Transfer) ...................... TF-152, TF-165
Controller Area Network (CAN) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
Converter housing installation ............ AT-246, AT-249
COOL/F - Wiring diagram ................................ EC-443
Coolant mixture ratio ......................................... MA-12
Coolant replacement ......................................... MA-13
Cooling circuit (engine) ........................................ CO-8
Cooling fan ........................................................ CO-15
Cooling fan control ........................................... EC-440
Cooling fan motor ............................................ EC-449
Cooling unit (A/C evaporator) ....... ATC-156, ATC-186
Corrosion protection ......................................... BL-165
Crankcase ventilation system - See Positive crankcase
ventilation .......................................................... EC-45
Crankshaft ......................................................... EM-74
Crankshaft position sensor (POS) ................... EC-284
Crash zone sensor .......................................... SRS-56
CVT shift lock system - Wiring diagram ........... AT-223
Cylinder block .................................................... EM-73
Cylinder block boring ......................................... EM-94
D
D/LOCK - Wiring diagram ................................... BL-19
Data link connector for Consult ......... EC-128, EC-140
Daytime light system .......................................... LT-33
Daytime running light - See Daytime light system .. LT-
33
Diagnosis sensor unit ...................................... SRS-59
Diagnostic trouble code (DTC) for OBD system . EC-8,
EC-53
Diagnostic trouble code (DTC) inspection priority chart
EC-101
Differential carrier assembly ............................ RFD-12
Differential carrier disassembly ....................... RFD-14
Differential gear oil replacement ........................ MA-25
Dimensions ......................................................... GI-49
Direct clutch solenoid valve ................ AT-148, AT-150
Display and amp.assembly .............................. ATC-61
Display Control Unit ......................................... AV-158
Dome light - See Interior lamp .......................... LT-129
Door glass .......................................... GW-68, GW-71
Door lock .......................................................... BL-131
Door mirror lamp ............................................... LT-129
Door trim .............................................................. EI-32
Door, front ........................................... BL-128, GW-68
Door, rear ........................................... BL-128, GW-71
Drive belt ........................................................... EM-12
Page 2257 of 3419
IDX-4
ALPHABETICAL INDEX
Drive chain (Transfer) ......................... TF-147, TF-174
Drive pinion diff. inspection ............................. RFD-13
Drive pinion height .......................................... RFD-18
Drive shaft (rear) ............................................... RAX-7
Driver air bag .................................................. SRS-46
DTC work support ............................................ EC-136
DTRL - Wiring diagram ....................................... LT-37
Duct and grilles .............................................. ATC-170
DVD Player ........................................................ AV-60
E
ECM input/output signal ..................... EC-117
, EC-141
ECM power supply ............................. EC-157, EC-393
ECM relay ........................................................ EC-157
ECM/PW - Wiring diagram ............................... EC-394
ECTS - Wiring diagram .................................... EC-197
Electric sunroof .................................................. RF-10
Electric throttle control actuator ......... EC-397, EC-399
Electrical load signal circuit .............................. EC-648
Electrical units location ...................................... PG-63
Electronic ignition (EI) system ........................... EC-26
Engine control circuit diagram ......................... EC-115
Engine control component parts location ......... EC-108
Engine control module (ECM) .......................... EC-383
Engine control system diagram ......................... EC-23
Engine coolant .................................................. CO-10
Engine coolant temperature sensor (ECTS) ... EC-195,
EC-208
Engine fail-safe system .................................... EC-103
Engine oil ............................................................. LU-7
Engine oil filter replacement ............................. MA-17
Engine oil precautions .......................................... GI-7
Engine oil replacement ..................................... MA-17
Engine removal ................................................. EM-69
Engine room cover ............................................ EM-11
Engine serial number .......................................... GI-48
ETC1 - Wiring diagram .................................... EC-400
ETC2 - Wiring diagram .................................... EC-407
ETC3 - Wiring diagram .................................... EC-411
EVAP canister .................................................... EC-35
EVAP canister purge volume control solenoid valve ....
EC-318
, EC-531
EVAP canister vent control valve ....... EC-325, EC-539
EVAP control system (small leak) diagnosis .. EC-309,
EC-349
, EC-357
EVAP control system pressure sensor .... EC-332, EC-
335, EC-341
EVAP control system purge flow monitoring diagnosis
EC-304
EVAP vapor lines inspection ............................. MA-20
Evaporative emission (EVAP) system ............... EC-32
Evaporator ..................................................... ATC-186
Exhaust manifold .............................................. EM-19
Exhaust system ................................................... EX-3
Exhaust system inspection .................................. EX-3
Expansion valve ............................................. ATC-188
F
F/FOG - Wiring diagram ..................................... LT-71
F/PUMP - Wiring diagram ............................... EC-638
Final drive pre-inspection .................. FFD-14, RFD-13
Final drive removal and installation ... FFD-11, RFD-10
Flow charts .......................................................... GI-27
Fluid temperature sensor (A/T) ........................ AT-126
Fluids ................................................................ MA-11
Fluorescent leak detector .............................. ATC-189
Fog lamp, front ................................................... LT-69
Foot lamp ......................................................... LT-130
Freeze frame data ............................... EC-54, EC-130
Front brake solenoid valve ................. AT-144, AT-146
Front bumper ...................................................... EI-13
Front case (Transfer) .......................... TF-147, TF-174
Front combination lamp removal and installation LT-32
Front door ............................. BL-128, BL-131, GW-68
Front Door Trim ................................................... EI-32
Front drive shaft (Transfer) ................. TF-147, TF-174
Front fog lamp .................................................... LT-69
Front passenger air bag .................................. SRS-51
Front seat ........................................................... SE-97
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ............... SRS-3, SRS-58
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTTS - Wiring diagram ...................... EC-255, EC-260
Fuel cut control (at no load high engine speed) EC-27
Fuel filter replacement ......................................... FL-5
Fuel gauge ............................................................ DI-5
Fuel injection system (Bank 1) .......... EC-236, EC-245
Fuel injection system (Bank 2) .......... EC-236, EC-245
Fuel injector and fuel tube ................................. EM-29
Fuel level sensor ................. EC-366, EC-368, EC-370
Fuel line inspection .............................................. FL-3
Fuel pressure check .......................................... EC-93
Fuel pressure release ....................................... EC-93
Fuel pump ....................................................... EC-637
Fuel pump and gauge .......................................... FL-5
Fuel system .......................................................... FL-3
Fuel tank .............................................................. FL-9
Fuel tank temperature sensor ........... EC-253, EC-259
Fuel tank vacuum relief valve ........................... EC-35
FUELB1 - Wiring diagram ................. EC-238, EC-247
FUELB2 - Wiring diagram ................. EC-239, EC-248
Fuse ...................................................... PG-66, PG-77
Fuse and fusible link box .................................. PG-77
Fuse block ......................................................... PG-76
Fusible link ............................................ PG-66, PG-77
G
Garage jack and safety stand ............................. GI-40
Gauges ................................................................. DI-5
Generator .......................................................... SC-17
Generic scan tool (GST) ................................. EC-139
Glass ...................................... GW-11, GW-68, GW-71
Glove box lamp ................................................ LT-153
Page 2258 of 3419
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
GPS antenna ..................................................... AV-62
Grease .............................................................. MA-11
Ground distribution ............................................ PG-29
H
H/AIM - Wiring diagram ...................................... LT-66
Handling precautions for plastics ..................... BL-187
Harness connector ............................................ PG-67
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-80
Headlamp aiming control ................................... LT-66
Headlamp leveler - See Headlamp aiming control . LT-
66
Headlamp removal and installation .................... LT-32
Heated oxygen sensor 2 (bank 1) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 (bank 2) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 heater (bank 1) ........ EC-166
Heated oxygen sensor 2 heater (bank 2) ........ EC-166
Heated seat ....................................................... SE-90
Heater and cooling unit (Heater core) . ATC-156, ATC-
160
Heater unit (heater core) ............... ATC-156, ATC-160
Height (Dimensions) ........................................... GI-49
HFC134a (R134a) system identification ........... ATC-7
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-175
HFC134a (R134a) system service tools ......... ATC-14
HFC134a system service equipment precaution ATC-
11
High & low reverse clutch solenoid valve . AT-152, AT-
154
Homelink universal transceiver ........................ BL-156
Horn ................................................................ WW-58
HORN - Wiring diagram .................................. WW-58
How to erase DTC for OBD system .................. EC-62
HSEAT - Wiring diagram ................................... SE-92
I
I/MIRR - Wiring diagram ................................... GW-75
IATS - Wiring diagram ..................................... EC-192
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................................. EC-562
ICC/SW - Wiring diagram ................................ EC-547
ICCBOF - Wiring diagram ............................... EC-650
Identification plate .............................................. GI-47
Idle air volume learning ..................................... EC-91
Idle mixture ratio ................................................ EC-79
Idle speed .............................................. EC-72, EC-77
Idle speed control (ISC) .................... EC-374, EC-376
Ignition coil .......................................... EM-26, EC-619
Ignition control system .................................... EC-619
Ignition key hole illumination ............................ LT-129
Ignition timing ........................................ EC-72, EC-77
IGNSYS - Wiring diagram ............................... EC-620
ILL - Wiring diagram ......................................... LT-158
Illumination ....................................................... LT-152
In vehicle sensor ........................... ATC-140, ATC-149
INJECT - Wiring diagram ................................. EC-632
Injector ............................................................. EC-631
Input clutch solenoid valve ................. AT-140, AT-142
Instrument panel .................................................. IP-10
Instrument panel speaker .................................. AV-46
Intake air temperature sensor ............ EC-191, EC-211
Intake door control linkage adjustment . ATC-85, ATC-
88
Intake door motor ........................... ATC-83, ATC-164
Intake manifold .................................................. EM-15
Intake sensor ................................ ATC-145, ATC-151
Integrated homelink transmitter - See Homelink univer-
sal tranceiver .................................................... BL-156
Intelligent cruise control (ICC) system ............... ACS-6
Interior ................................................................. EI-35
Interior lamp ...................................................... LT-129
Interior lamp on-off control ................................ LT-130
Internal gear (Transfer) ....................... TF-147, TF-174
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVIS (Infiniti vehicle immobilizer system) .......... BL-137
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
J
Jacking points ..................................................... GI-40
Junction box (J/B) .............................................. PG-76
K
Key illumination ................................................ LT-130
KEYLES - Wiring diagram .................................. BL-49
Knock sensor (KS) ........................................... EC-279
KS - Wiring diagram ........................................ EC-280
L
Length (Dimensions) .......................................... GI-49
License lamp .................................................... LT-108
Lifting points ....................................................... GI-41
Line pressure solenoid valve ........................... AT-119
Line pressure switch (Transfer) .......... TF-152, TF-165
Line pressure test (A/T) ..................................... AT-51
Location of electrical units ................................. PG-63
Low coast brake solenoid valve .......... AT-156, AT-158
Low tire pressure warning system ...................... WT-8
Low tire pressure warning system - trouble diagnoses
WT-11
Low tire pressure warning system - Wiring diagram .....
WT-11
Lubricant (R134a) A/C ..................................... ATC-22
Lubricants .......................................................... MA-11
Lubrication circuit (engine) .................................. LU-5
Lubrication oil A/C ........................................... ATC-22
Lubrication-locks, hinges and hood latches ....... MA-31
Page 2259 of 3419
IDX-6
ALPHABETICAL INDEX
M
MAFS - Wiring diagram ..................... EC-177
, EC-185
Magnet clutch ............................... ATC-115, ATC-180
MAIN - Wiring diagram .................................... EC-157
Main oil pump (Transfer) ..................... TF-152, TF-165
Mainshaft (Transfer) ........................... TF-152, TF-165
Maintenance (engine)Schedule 1 ....................... MA-7
Maintenance (engine)Schedule 2 ....................... MA-9
Major overhaul (Final drive) .............. FFD-13, RFD-14
Major overhaul (Transfer) ................................ TF-144
Malfunction indicator lamp (MIL) ........................ EC-64
Map lamp .......................................................... LT-130
Mass air flow sensor (MAFS) ............. EC-174, EC-183
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-10
MIL data link connectors circuit ....................... EC-667
MIL/DL - Wiring diagram .................................. EC-667
Misfire .............................................................. EC-271
Mode door control linkage adjustment ............. ATC-66
Mode door motor ............................ ATC-64, ATC-165
Model variation ................................................... GI-46
Multiport fuel injection (MFI) system .................. EC-24
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ............................................................... BL-44
N
NATS - Wiring diagram .................................... BL-140
NAVI - Wiring diagram ....................................... AV-79
NAVI Control Unit ............................................ AV-157
Neutral-4LO switch ............................................ TF-62
NVH troubleshooting (AX) ................................. FAX-4
NVH troubleshooting (EM) .................................. EM-9
NVH troubleshooting (Final drive) ..................... RFD-5
NVH troubleshooting (Propeller shaft) ................. PR-3
NVH troubleshooting (RAX) .............................. RAX-4
NVH troubleshooting (RSU) .............................. RSU-5
NVH troubleshooting (ST) .................................... PS-5
NVH troubleshooting (Transfer) ......................... TF-10
NVH troubleshooting (WT)NVH troubleshooting (WT) .
WT-4
NVIS (Nissan vehicle immobilizer system) precautions
GI-3
O
O2H2B1 - Wiring diagram ................................ EC-168
O2H2B2 - Wiring diagram ................................ EC-170
O2S2B1 - Wiring diagram .. EC-218, EC-228, EC-418,
EC-429
O2S2B2 - Wiring diagram .. EC-220, EC-230, EC-420,
EC-431
Oil cooler (engine) ............................................. LU-11
Oil filter ............................................................... LU-10
Oil filter (Transfer) ............................................ TF-141
Oil pan (engine) ................................................ EM-22
Oil pressure (engine) ........................................... LU-7
Oil pressure relief valve (engine) ......................... LU-5
Oil pump (engine) .............................................. LU-13
Oil seal replacement (engine) ........................... EM-55
Oil seal replacement (front of final drive) FFD-7, RFD-6
Oil seal replacement (side of final drive) FFD-9, RFD-8
On board diagnostic system ............................. EC-48
ORVR (On-board Refueling Vapor Recovery) .. EC-39
Overheat ......................................................... EC-440
P
P/SCKT - Wiring diagram ................................. WW-56
Pantograph jack .................................................. GI-40
Park/Neutral position switch ............................ EC-581
Park/neutral position switch (A/T) .................... AT-104
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................ EC-45
Periodic maintenance ......................................... MA-7
Personal lamp .................................................. LT-130
PGC/V - Wiring diagram ................... EC-320, EC-533
PHASE - Wiring diagram ................................ EC-291
Pinion bearing preload diff. ............................. RFD-22
Piston pin inspection ......................................... EM-89
Piston ring inspection ........................................ EM-90
Piston to bore clearance ................................... EM-94
Planetary carrier (Transfer) ................. TF-147, TF-174
PNP/SW - Wiring diagram .............................. EC-583
POS - Wiring diagram ..................................... EC-286
POWER - Wiring diagram ................................... PG-6
Power door lock ................................................. BL-16
Power seat ......................................................... SE-89
Power steering fluid level .................................. MA-29
Power steering gear ........................................... PS-15
Power steering oil pump .................................... PS-26
Power steering pressure (PSP) sensor ........... EC-378
Power steering system bleeding .......................... PS-6
Power supply routing .......................................... PG-4
Power window .................................................. GW-15
PRE/SE - Wiring diagram ................. EC-337, EC-343
Precautions (General) ........................................... GI-4
Precautions in repairing high strength steel ..... BL-190
Pressure switch 1 ............................... AT-146, AT-160
Pressure switch 2 ............................................. AT-158
Pressure switch 3 ............................... AT-142, AT-162
Pressure switch 5 ............................... AT-150, AT-164
Pressure switch 6 ............................... AT-154, AT-166
Pressure test (A/T) ............................................. AT-51
Propeller shaft ........................................... PR-4, PR-8
Propeller shaft inspection .................................. MA-25
Propeller shaft on vehicle service ....................... PR-8
Propeller shaft vibration ............................ PR-4, PR-8
PS/SEN - Wiring diagram ............................... EC-379
R
R/VIEW - Wiring diagram .................................... DI-74
Radiator ............................................................ CO-12
Rear Audio Remote Control Unit ....................... AV-47
Rear axle ........................................................... RAX-5
Page 2261 of 3419
IDX-8
ALPHABETICAL INDEX
Torque converter installation AT-245, AT-246, AT-248,
AT-249
Torque convertor clutch solenoid valve ... AT-115, AT-
117
Tow truck towing ................................................. GI-42
Towing point ....................................................... GI-43
TPS1 - Wiring diagram .................................... EC-266
TPS2 - Wiring diagram .................................... EC-203
TPS3 - Wiring diagram .................................... EC-606
Traction control system - Wiring diagram ....... BRC-16
Transfer control device ............. TF-76, TF-80, TF-138
Transfer control unit inspection table ................. TF-36
Transfer dropping resistor .................................. TF-90
Transfer fluid temperature sensor TF-104, TF-152, TF-
165
Transfer motor .................................... TF-102, TF-140
Transfer motor relay ........................................ TF-102
Transfer oil replacement ................................... MA-24
Transfer serial number ........................................ GI-48
Transmission serial number ................................ GI-48
Tread-FR&RR (Dimensions) ............................... GI-49
Trim ..................................................................... EI-35
TRNSCV - Wiring diagram .................. BL-140, BL-156
Trouble diagnoses .............................................. GI-11
Turbine revolution sensor ................................ AT-131
TURN - Wiring diagram ...................................... LT-83
Turn signal lamp ................................................. LT-80
Two trip detection logic ...................................... EC-48
Two-pole lift ........................................................ GI-41
V
Vacuum hose (brake system) ............................ BR-19
Vacuum hose drawing (Engine control) ........... EC-114
Valve clearance ................................................ EM-51
Valve guide ....................................................... EM-65
Vanity mirror lamp ............................................. LT-129
VDC (vehicle dynamics control) ........................ BRC-7
VDC -Wiring diagram ...................................... BRC-16
Vehicle identification number .............................. GI-47
Vehicle recovery (freeing a stuck vehicle) .......... GI-43
Vehicle security (theft warning) system ............. BL-75
Vehicle speed sensor (VSS) ............................ EC-372
VEHSEC - Wiring diagram ................................. BL-79
VENT/V - Wiring diagram .................. EC-327, EC-541
Video Monitor ..................................................... AV-60
VIN registration .................................................. EC-90
Viscosity number (SAE) .................................... MA-12
W
W/ANT - Wiring diagram .................................... AV-49
Wait detection switch ......................................... TF-69
WARN - Wiring diagram ..................................... DI-31
Warning chime .................................................... DI-42
Warning lamps .................................................... DI-30
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-35
Water pump ...................................................... CO-17
Water temperature gauge ..................................... DI-5
Wheel alignment (front) ..................................... FSU-6
Wheel alignment (rear) ................................... RSU-27
Wheel bearing (front) ........................................ FAX-5
Wheel bearing (rear) ......................................... RAX-5
Wheel hub (rear) ............................................... RAX-5
Wheel size .......................................................... GI-49
Wheelbase (Dimensions) .................................... GI-49
Width (Dimensions) ............................................. GI-49
WINDOW - Wiring diagram .............................. GW-22
Window, door ...................................... GW-68, GW-71
Windshield ....................................................... GW-11
WIP/R - Wiring diagram ................................... WW-39
WIPER - Wiring diagram .................................. WW-11
Wiper, front ........................................................ WW-4
Wiper, rear ....................................................... WW-35
Wiring Diagram (Cell code) list ......................... PG-60
Wiring diagrams .................................................. GI-15
WT-T/WARN - Wiring diagram .......................... WT-11
Page 2453 of 3419
LT-6
HEADLAMP (FOR USA)
Revision: October 20052005 QX56
HEADLAMP (FOR USA)PFP:26010
Component Parts and Harness Connector LocationEKS00B7S
System DescriptionEKS00B7T
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
requesting the headlamps (and tail lamps) illuminate. This input is communicated to the IPDM E/R (intelligent
power distribution module engine room) across the CAN communication lines. The CPU (central processing
unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When energized, these relays
direct power to the respective headlamps, which then illuminate.
OUTLINE
Power is supplied at all times
to ignition relay, located in the IPDM E/R, and
to headlamp high relay, located in the IPDM E/R, and
to headlamp low relay, located in the IPDM E/R, and
through 20A fuse (No. 53, located in the IPDM E/R)
to CPU of the IPDM E/R, and
through 50A fusible link (letter f , located in the fuse and fusible link box)
WKIA3463E
Page 2477 of 3419
LT-30
HEADLAMP (FOR USA)
Revision: October 20052005 QX56
Aiming AdjustmentEKS00B89
For details, refer to the regulations in your state.
Before performing aiming adjustment, check the following.
1. Ensure all tires are inflated to correct pressure.
2. Place vehicle and screen on level surface.
3. Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant and engine oil filled to correct level, and fuel tank full.
4. Confirm spare tire, jack and tools are properly stowed.
5. If equipped, confirm headlamp aiming switch is set to "0" (zero) position.
LOW BEAM AND HIGH BEAM
NOTE:
Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
1. Turn headlamp low beam on.
2. Use adjusting screw to perform aiming adjustment.
WKIA1859E
Page 2481 of 3419
LT-34
HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
Revision: October 20052005 QX56
System DescriptionEKS00B8E
Daytime light system turns on daytime light lamps while driving. Daytime light lamps are not turned on if
engine is activated with parking brake applied. Release parking brake to turn on daytime light lamps. The
lamps turn off when lighting switch is in the 2ND position or AUTO position (Headlamp is "ON") and when light-
ing switch is in the PASSING position. (Daytime light lamps are not turned off only by parking brake itself.)
A parking brake signal and engine run or stop signal are sent to BCM (body control module) by CAN commu-
nication line.
OUTLINE
Power is supplied at all times
to ignition relay, located in the IPDM E/R (intelligent power distribution module engine room), and
through 50A fusible link (letter f , located in the fuse and fusible link box)
to BCM terminal 70, and
through 20A fuse (No. 53, located in the IPDM E/R)
to CPU (central processing unit) of the IPDM E/R, and
through 10A fuse [No. 19, located in the fuse block (J/B)]
to combination meter terminal 8, and
through 10A fuse (No. 45, located in the IPDM E/R)
to daytime light relay terminals 2 and 5.
When the ignition switch is in ON or START position, power is supplied
to ignition relay, located in the IPDM E/R, and
through 10A fuse (No. 59, located in the fuse and relay box)
to BCM terminal 38, and
through 10A fuse [No. 14, located in the fuse block (J/B)]
to combination meter terminal 24.
Ground is supplied
to BCM terminal 67 and
to combination meter terminal 17
through grounds M57, M61 and M79.
DAYTIME LIGHT OPERATION
With the engine running, the lighting switch in the OFF or 1ST position and parking brake released, the IPDM
E/R receives input requesting the daytime lights illuminate. This input is communicated across the CAN com-
munication lines. The CPU of the IPDM E/R controls the daytime light relay coil. When energized, this relay
directs power
through daytime light relay terminal 3
to front combination lamp LH terminal 2
through front combination lamp LH terminal 6
to IPDM E/R terminal 55
through 10A fuse (No. 35, located in the IPDM E/R)
through 10A fuse (No. 34, located in the IPDM E/R)
through IPDM E/R terminal 56
to front combination lamp RH terminal 6.
Ground is supplied
to front combination lamp RH terminal 2
through grounds E9, E15 and E24.
With power and ground supplied, the daytime lights illuminate. The high beam headlamps are now wired in
series and illuminate at a reduced intensity.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .