service indicator INFINITI QX4 2005 Factory Owner's Guide

TF-3
C
E
F
G
H
I
J
K
L
MA
B
TF
Revision: October 20052005 QX56 DIAGNOSTIC PROCEDURE ............................. 117
4WD Warning Lamp Does Not Turn ON .............. 121
SYMPTOM: ....................................................... 121
DIAGNOSTIC PROCEDURE ............................ 121
4WD Shift Indicator Lamp or 4LO Indicator Lamp
Does Not Change ................................................. 123
SYMPTOM: ....................................................... 123
DIAGNOSTIC PROCEDURE ............................ 124
ATP Warning Lamp Turns ON .............................. 125
SYMPTOM: ....................................................... 125
DIAGNOSTIC PROCEDURE ............................ 125
4LO Indicator Lamp Repeats Flashing ................. 127
SYMPTOM: ....................................................... 127
DIAGNOSTIC PROCEDURE ............................ 127
4WD Warning Lamp Flashes Rapidly .................. 128
SYMPTOM: ....................................................... 128
DIAGNOSTIC PROCEDURE ............................ 128
4WD Warning Lamp Flashes Slowly .................... 129
SYMPTOM: ....................................................... 129
DIAGNOSTIC PROCEDURE ............................ 129
Heavy Tight-corner Braking Symptom Occurs ..... 130
SYMPTOM: ....................................................... 130
DIAGNOSTIC PROCEDURE ............................ 130
4WD System Does Not Operate .......................... 131
SYMPTOM: ....................................................... 131
DIAGNOSTIC PROCEDURE ............................ 131
TRANSFER CONTROL UNIT ................................. 132
Removal and Installation ...................................... 132
REMOVAL ......................................................... 132
INSTALLATION ................................................. 132
FRONT OIL SEAL .................................................. 133
Removal and Installation ...................................... 133
REMOVAL ......................................................... 133
INSTALLATION ................................................. 134
REAR OIL SEAL .................................................... 135
Removal and Installation ...................................... 135
REMOVAL ......................................................... 135
INSTALLATION ................................................. 135SIDE OIL SEAL .......................................................137
Removal and Installation ......................................137
REMOVAL .........................................................137
INSTALLATION .................................................137
TRANSFER CONTROL DEVICE ............................138
Removal and Installation ......................................138
AIR BREATHER HOSE ..........................................139
Removal and Installation ......................................139
TRANSFER MOTOR ...............................................140
Removal and Installation ......................................140
REMOVAL .........................................................140
INSTALLATION .................................................140
TRANSFER OIL FILTER .........................................141
Removal and Installation ......................................141
REMOVAL .........................................................141
INSTALLATION .................................................141
TRANSFER ASSEMBLY ........................................143
Removal and Installation ......................................143
REMOVAL .........................................................143
INSTALLATION .................................................143
Disassembly and Assembly ..................................144
COMPONENTS .................................................144
DISASSEMBLY .................................................146
INSPECTION AFTER DISASSEMBLY ..............161
ASSEMBLY .......................................................165
SERVICE DATA AND SPECIFICATIONS (SDS) ....181
General Specifications ..........................................181
Inspection and Adjustment ...................................181
CLEARANCE BETWEEN INNER GEAR AND
OUTER GEAR ...................................................181
CLUTCH ............................................................181
PINION GEAR END PLAY ................................181
CLEARANCE BETWEEN SHIFT FORK AND
SLEEVE ............................................................181
SELECTIVE PARTS ..........................................181

TF-4
PRECAUTIONS
Revision: October 20052005 QX56
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EDS002H3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NIN G:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Transfer Assembly and Transfer Control Unit ReplacementEDS002H4
When replacing transfer assembly or transfer control unit, check the 4WD shift indicator lamp as follows.
1. Turn ignition switch “ON”.
2. Check 4WD shift indicator lamp is turned ON for approx. 1 second.

If OK, the position between transfer assembly and transfer control unit is correct.

If NG, the position is different between transfer assembly and transfer control unit.
Adjust the position between transfer assembly and transfer control unit. Refer to TF-4, "
METHOD FOR
POSITION ADJUSTMENT" .
METHOD FOR POSITION ADJUSTMENT
1. Start engine. Run the engine for at least 10 seconds.
2. Stop vehicle and move A/T selector lever to “N” position with brake pedal depressed. Stay in "N" for at
least 2 seconds.
3. Turn 4WD shift switch to “2WD” position. Stay in "2WD" for at least 2 seconds.
4. Turn ignition switch “OFF”.
5. Start engine.
6. Erase self-diagnosis. Refer to TF-47, "
How to Erase Self-diagnostic Results" (with CONSULT-II) or TF-
53, "ERASE SELF-DIAGNOSIS" (without CONSULT-II).
7. Check 4WD shift indicator lamp. Refer to TF-32, "
CHECK BEFORE ENGINE IS STARTED" .
If 4WD shift indicator lamp does not indicate "2WD", install new transfer control unit and retry the above
check.
PrecautionsEDS002H5

Before connecting or disconnecting the transfer control
unit harness connector, turn ignition switch “OFF” and dis-
connect battery ground cable. Failure to do so may damage
the transfer control unit. Battery voltage is applied to trans-
fer control unit even if ignition switch is turned “OFF”.
SEF 2 89 H