transmission fluid INFINITI QX56 2004 Factory User Guide

AT-78
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
30
Slips/Will
Not
engageNo shock at all or the
clutch slips when
vehicle changes
speed D
4 → D5 .ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT-5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. Front brake (brake band)AT- 2 7 3
11. Input clutchAT- 2 9 5
12. Gear systemAT- 2 6 1
13. High and low reverse clutchAT- 3 0 5
31When you press the
accelerator pedal and
shift speed D5 → D4
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT-5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. Input clutchAT- 2 9 5
11. Gear systemAT- 2 6 1
12. High and low reverse clutchAT- 3 0 5
13. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-79
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
32
Slips/Will
Not
engageWhen you press the
accelerator pedal and
shift speed D4 → D3
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 7 8,
AT- 1 4 5
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5,
AT- 1 5 1
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT- 5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converter AT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 3rd one-way clutchAT- 2 9 2
11. Gear systemAT- 2 6 1
12. High and low reverse clutchAT- 3 0 5
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
33When you press the
accelerator pedal and
shift speed D3 → D2
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 8 4,
AT- 1 6 3
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
5. CAN communication lineAT- 1 0 3
6. Line pressure testAT- 5 9
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 3rd one-way clutchAT- 2 9 2
11. Gear systemAT- 2 6 1
12. Direct clutchAT- 3 0 7
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

AT-80
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
34
Slips/Will
Not
EngageWhen you press the
accelerator pedal and
shift speed D2 → D1
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 8
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7
4. CAN communication lineAT- 1 0 3
5. Line pressure testAT-5 9
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. 3rd one-way clutchAT- 2 9 2
10. 1st one-way clutchAT- 3 0 0
11. Gear systemAT- 2 6 1
12. Reverse brakeAT- 2 7 3
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
35With selector lever in
“D” position, accelera-
tion is extremely poor.ON vehicle1. Fluid level and stateAT-5 8
2. Line pressure testAT-5 9
3. Accelerator pedal position sensorAT- 1 2 9
4. CAN communication lineAT- 1 0 3
5. PNP switchAT- 1 0 9
6. Control cable adjustmentAT- 2 3 4
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Torque converterAT- 2 7 3
9. Oil pump assemblyAT- 2 9 0
10. 1st one-way clutchAT- 3 0 0
11. Gear systemAT- 2 6 1
12. Reverse brakeAT- 2 7 3
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-87
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
56
OthersMaximum speed low.ON vehicle1. Fluid level and stateAT- 5 8
2. Line pressure testAT- 5 9
3. Accelerator pedal position sensorAT- 1 2 9
4. CAN communication lineAT- 1 0 3
5. Direct clutch solenoid valveAT- 1 5 7
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. Input clutchAT- 2 9 5
10. Gear systemAT- 2 6 1
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
57Extremely large
creep.ON vehicle1. Engine idle speed EC-32

2. CAN communication lineAT- 1 0 3
3. ATF pressure switch 5AT- 1 8 1
OFF vehicle 4. Torque converterAT- 2 7 3
58With selector lever in
“P” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT- 1 9 3 , "
In
“P” Position, Vehicle
Moves When Pushed"
.ON vehicle1. PNP switchAT- 1 0 9
2. Control cable adjustmentAT- 2 3 4
3. Parking pawl componentsAT- 2 6 1
59Vehicle runs with
transmission in “P”
position.ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT- 5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
5. Parking pawl componentsAT- 2 6 1
OFF vehicle 6. Gear systemAT- 2 6 1
No. Items Symptom Condition Diagnostic ItemReference
page

AT-88
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
60
OthersVehicle runs with
transmission in “N”
position.
Refer to AT-194, "In
“N” Position, Vehicle
Moves" .ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT-5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Input clutchAT- 2 9 5
6. Gear systemAT- 2 6 1
7. Direct clutchAT- 3 0 7
8. Reverse brakeAT- 2 7 3
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
61Engine does not start
in “N” or “P” position.
Refer to AT-192, "Engine Cannot Be
Started In “P” or “N”
Position" .ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
62Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
63 Engine stall.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
64Engine stalls when
select lever shifted “N”
→ “D”, “R”.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

DTC P1702 TRANSMISSION CONTROL MODULE (RAM)
AT-127
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
DTC P1702 TRANSMISSION CONTROL MODULE (RAM)PFP:31036
DescriptionUCS002EP
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls the A/T.
On Board Diagnosis LogicUCS002EQ

This is not an OBD-II self-diagnostic item.

Diagnostic trouble code “TCM·RAM” with CONSULT-II is detected when TCM memory RAM is malfunc-
tioning.
Possible CauseUCS002ER
TCM.
DTC Confirmation ProcedureUCS002ES
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Run engine for at least 2 consecutive seconds at idle speed.
5. If DTC is detected, go to AT - 1 2 7 , "
Diagnostic Procedure" .
Diagnostic ProcedureUCS002ET
1. CHECK DTC
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II.
3. Touch “ERASE”.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Perform “DTC Confirmation Procedure”, AT-127, "
DTC Confir-
mation Procedure" .
Is the
“TCM·RAM” displayed again?
YES >> Replace the control valve with TCM. Refer to AT-241,
"Control Valve With TCM and A/T Fluid Temperature
Sensor 2" .
NO >>INSPECTION END
BCIA0030E
BCIA0031E

AT-128
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)
Revision: August 20072004 QX56
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)PFP:31036
DescriptionUCS002EU
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls the A/T.
On Board Diagnosis LogicUCS002EV

This is not an OBD-II self-diagnostic item.

Diagnostic trouble code “TCM·ROM” with CONSULT-II is detected when TCM memory ROM is malfunc-
tioning.
Possible CauseUCS002EW
TCM.
DTC Confirmation Procedure UCS002EX
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch to “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for A/T with CONSULT-II.
3. Start engine.
4. Run engine for at least 2 consecutive seconds at idle speed.
5. If DTC is detected, go to AT-128, "
Diagnostic Procedure" .
Diagnostic ProcedureUCS002EY
1. CHECK DTC
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELF-DIAG RESULTS” mode for “A/T” with CONSULT-
II.
3. Touch “ERASE”.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Perform “DTC Confirmation Procedure”, AT-128, "
DTC Confir-
mation Procedure" .
Is the
“TCM·ROM” displayed again?
YES >> Replace the control valve with TCM. Refer to AT-241,
"Control Valve With TCM and A/T Fluid Temperature
Sensor 2" .
NO >>INSPECTION END
BCIA0030E
BCIA0031E

AT-196
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
4. CHECK A/T FLUID LEVEL
Check the A/T fluid level. Refer to AT-13, "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 5.
NG >> Refill ATF.
5. CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer
to AT - 5 9 , "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
–Power train system. Refer to AT-273, "Disassembly" .
–Transmission case. Refer to AT-273, "Disassembly" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
SAT6 3 8A
SAT4 9 4G

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-199
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
5. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
2. Check the following items:
–Reverse brake. Refer to AT-273, "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
6. CHECK LINE PRESSURE
Check the line pressure with the engine idling. Refer to AT-59, "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 9.
NG - 1 >> Line pressure high. GO TO 7.
NG - 2 >> Line pressure low. GO TO 8.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
8. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 7 3 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
–Power train system. Refer to AT- 2 7 3 , "Disassembly" .
–Transmission case. Refer to AT - 2 7 3 , "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
SAT4 9 4G

AT-202
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
5. CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer
to AT - 5 9 , "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
–Power train system. Refer to AT-273, "Disassembly" .
–Transmission case. Refer to AT-273, "Disassembly" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 8 , "
Fluid Condition
Check" .
OK or NG
OK >> GO TO 9.
NG >> GO TO 12.
SAT4 9 4G
SCIA5199E