transmission oil INFINITI QX56 2004 Factory Owner's Manual

AT-216
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
3. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT- 5 9 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 6.
NG - 1 >> Line pressure high. GO TO 4.
NG - 2 >> Line pressure low. GO TO 5.
4. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-273, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-290, "Oil Pump" .
–Power train system. Refer to AT-273, "Disassembly" .
–Transmission case. Refer to AT-273, "Disassembly" .
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
6. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-241, "
Control Valve With TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 8 , "
Fluid Condition
Check" .
OK or NG
OK >> GO TO 7.
NG >> GO TO 10.
SAT4 9 4G
SCIA5199E

ON-VEHICLE SERVICE
AT-241
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
ON-VEHICLE SERVICEPFP:00000
Control Valve With TCM and A/T Fluid Temperature Sensor 2UCS002J B
COMPONENTS
1. Transmission 2. Control valve with TCM 3. Bracket
4. A/T fluid temperature sensor 2 5. Oil pan gasket 6. Oil pan
7. Magnet 8. Drain plug gasket 9. Drain plug
10. Oil pan mounting bolt 11. Snap ring 12. O-ring
SCIA5190E

ON-VEHICLE SERVICE
AT-247
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
9. Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip.
10. Connect revolution sensor connector.
11. Securely fasten revolution sensor harness with terminal clips.
12. Install magnets in oil pan.
13. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan.
CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old gasket, etc. From oil pan gasket mounting surfaces.
SCIA5146E
SCIA5024E
SCIA3969E
SCIA5200E

AT-248
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old gasket, etc.
From oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse oil pan mounting bolts.
14. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse drain plug gasket.
15. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
16. Install snap ring to A/T assembly harness connector.
17. Connect A/T assembly harness connector.
18. Pour ATF into transmission assembly. Refer to AT - 1 3 , "
Chang-
ing A/T Fluid" .
19. Connect the negative battery terminal
SCIA2308E
SCIA2492E
SCIA5038E
SCIA5039E

ON-VEHICLE SERVICE
AT-251
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
3. Connect A/T fluid temperature sensor 2 connector.
4. Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan.
CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old sealant, etc. From oil pan gasket mounting surfaces.
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old sealant, etc.
From oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT- 2 4 1 , "
COMPONENTS" .
CAUTION:
Do not reuse oil pan mounting bolts.
6. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-241, "
COMPONENTS" .
CAUTION:
Do not reuse drain plug gasket.
7. Pour ATF into transmission assembly. Refer to AT-13, "
Chang-
ing A/T Fluid" .
8. Connect the negative battery terminal
SCIA5023E
SCIA5146E
SCIA2308E
SCIA2492E

AT-252
ON-VEHICLE SERVICE
Revision: August 20072004 QX56
Rear Oil SealUCS002JC
REMOVAL AND INSTALLATION
Removal
1. Remove rear propeller shaft.Refer to PR-9, "REMOVAL" .
2. Remove transfer from transmission (4WD models). Refer to TF-
109, "REMOVAL AND INSTALLATION" .
3. Remove rear oil seal using a flat-bladed screwdriver.
CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (4WD models).
Installation
CAUTION:
After completing installation, check fluid leakage and fluid level. Refer to AT-1 3, "
Changing A/T Fluid"
,AT- 1 3 , "Checking A/T Fluid" .
1. As shown below, use a drift to drive rear oil seal into the exten-
sion case (2WD models) or adapter case (4WD models) until it
is flush.
CAUTION:

Apply ATF to rear oil seal.

Do not reuse rear oil seal
2. Install transfer to transmission (4WD models). Refer to TF-109,
"REMOVAL AND INSTALLATION" .
3. Install rear propeller shaft. Refer to PR-9, "
INSTALLATION" .
SCIA5254E
SCIA5255E

TRANSMISSION ASSEMBLY
AT-257
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

AT-260
TRANSMISSION ASSEMBLY
Revision: August 20072004 QX56
INSTALLATION
Installation of the remaining components is in the reverse order of
the removal, while paying attention to the following work.

If removed, install drive plate.
–Align dowel pin of crankshaft rear end with pin holes of each
parts to install.
–Install drive plate, reinforcement plate and pilot converter as
shown.
–Face chamfered or rounded edge side to crankshaft.
CAUTION:

When replacing an engine or transmission you must make
sure the dowels are installed correctly during re-assembly.

Improper alignment caused by missing dowels may cause
vibration, oil leaks or breakage of drivetrain components.

When installing transmission to the engine, attach the bolts in
accordance with the following standard.
*: No.2 bolt also secures air breather vent.
–Align the positions of tightening bolts for drive plate with those of
the torque converter, and temporarily tighten the bolts. Then,
tighten the bolts with the specified torque.
CAUTION:

When turning crankshaft, turn it clockwise as viewed from the front of the engine.

After converter is installed to drive plate, rotate crankshaft several turns and check to be sure that
transmission rotates freely without binding.

After completing installation, check fluid leakage, fluid level, and the positions of A/T. Refer to AT-13,
"Checking A/T Fluid" , AT-234, "Checking of A/T Position" , AT-234, "Adjustment of A/T Position" .
KBIA2494E
KBIA2537E
Bolt No. 1 2* 3
Number of bolts 4 1 4
Bolt length
“”mm (in)70 (2.76) 70 (2.76) 70 (2.76)
Tightening torque
N·m (kg-m, ft-lb)11 3
(12, 83)11 3
(12, 83)
LCIA0371E
LCIA0335E

AT-266
OVERHAUL
Revision: August 20072004 QX56
7. Parking pawl 8. Pawl shaft 9. Self-sealing bolt
10. Bracket 11. Seal ring 12. Needle bearing
13. Revolution sensor 14. Parking gear 15. Output shaft
16. Bearing race 17. Needle bearing 18. Manual plate
19. Parking rod 20. Manual shaft oil seal 21. Manual shaft
22. O-ring 23. Band servo anchor end pin 24. Detent spring
25. Spacer 26. Seal rings 27. Snap ring
28. O-ring 29. Transmission case 30. Retaining pin
31. Return spring 32. O-ring 33. Servo assembly
34. Snap ring 35. Control valve with TCM 36. Bracket
37. A/T fluid temperature sensor 2 38. Oil pan gasket 39. Oil pan
40. Magnet 41. Drain plug 42. Drain plug gasket
43. Oil pan mounting bolt

AT-268
OVERHAUL
Revision: August 20072004 QX56
7. Pawl shaft 8. Bracket 9. Self-sealing bolt
10. Seal ring 11. Needle bearing 12. Gasket
13. Revolution sensor 14. Parking gear 15. Output shaft
16. Bearing race 17. Needle bearing 18. Manual plate
19. Parking rod 20. Manual shaft oil seal 21. Manual shaft
22. O-ring 23. Band servo anchor end pin 24. Detent spring
25. Spacer 26. Seal ring 27. Snap ring
28. O-ring 29. Transmission case 30. Retaining pin
31. Return spring 32. O-ring 33. Servo assembly
34. Snap ring 35. Control valve with TCM 36. Bracket
37. A/T fluid temperature sensor 2 38. Oil pan gasket 39. Oil pan
40. Magnet 41. Drain plug 42. Drain plug gasket
43. Oil pan mounting bolt