door lock INFINITI QX56 2006 Factory Service Manual

POWER WINDOW SYSTEMGW-35
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
Trouble Diagnoses Symptom ChartEIS005XX

Check that other systems using the signal of the following systems operate normally.
DOOR SW-DRIndicates (ON/OFF) condition of front door switch driver side
DOOR SW-AS Indicates (ON/OFF) condition of front door switch passenger side
Symptom Repair orderRefer to page
None of the power windows can be operated using any switch 1. BCM power supply and ground circuit check
GW-37
2. Main power window and door lock/unlock
power supply and ground circuit checkGW-38
3. Power window serial link check front LH and
RHGW-39
Front power window LH alone does not operate 1. Main power window and door lock/unlock
power supply and ground circuit check
GW-382. Front power window motor LH circuit check
GW-40
3. Replace main power window and door lock/
unlock switch EI-32
Front power window RH alone does not operate 1. Power window and door lock/unlock switch
RH power supply and ground circuit check
GW-392. Power window serial link check front LH and
RHGW-51
3. Front power window motor RH circuit check
GW-41
4. Replace BCMBCS-20
Rear power window LH alone does not operate 1. Rear power window control unit LH or RH
power supply and ground circuit check
GW-53
2. Rear power window switch LH or RH power
supply and ground circuit checkGW-54
3. Rear power window motor LH circuit check
GW-54
4. Power window serial link check rear LH and
RHGW-59
5. Replace BCM
BCS-20
Rear power window RH alone does not operate 1. Rear power window control unit LH or RH
power supply and ground circuit check
GW-53
2. Rear power window switch LH or RH power
supply and ground circuit checkGW-54
3. Rear power window motor RH circuit check
GW-55
4. Power window serial link check rear LH and
RHGW-59
5. Replace BCM
BCS-20
Rear power vent windows do not operate 1. Rear power vent window switch circuit checkGW-61
Rear power vent window LH alone does not operate 1. Rear power vent window motor LH circuit
checkGW-61
Rear power vent window RH alone does not operate
1. Rear power vent window motor RH circuit
checkGW-61
Rear power vent windows do not open 1. Rear power vent window relay (OPEN)
check
GW-61
Rear power vent windows do not close 1. Rear power vent window relay (CLOSE)
checkGW-61

GW-36
POWER WINDOW SYSTEM
Revision: November 20092006 QX56
Anti-pinch system does not operate normally (Front LH)1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.
—
2. Limit switch adjusting GW-66
3. Limit switch circuit check front LHGW-41
4. Encoder circuit check front LHGW-44
Anti-pinch system does not operate normally (Front RH) 1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.
—
2. Limit switch adjusting GW-66
3. Limit switch circuit check front RHGW-43
4. Encoder circuit check front RHGW-46
Anti-pinch system does not operate normally (Rear LH) 1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.
—
2. Limit switch adjusting GW-66
3. Limit switch circuit check rear LH or RHGW-56
4. Encoder circuit check rear LH or RHGW-58
Anti-pinch system does not operate normally (Rear RH) 1. Door window sliding part malfunction

A foreign material adheres to window glass
or glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.
—
2. Limit switch adjusting GW-66
3. Limit switch circuit check rear LH or RHGW-56
4. Encoder circuit check rear LH or RHGW-58
Power window retained power operation does not operate properly 1. Check the retained power operation mode
setting.
GW-342. Door switch check
GW-48
3. Replace BCM.BCS-20
Power windows do not operate by front door lock assembly LH
(key cylinder switch) 1. Front door lock assembly LH (key cylinder
switch) check
GW-49
2. Replace main power window and door lock/
unlock switch
EI-32
Power window lock switch does not function
1. Power window lock switch circuit checkGW-51
Symptom Repair orderRefer to page

GW-38
POWER WINDOW SYSTEM
Revision: November 20092006 QX56
Main Power Window and Door Lock/Unlock Switch Power Supply and Ground
Circuit Check
EIS005XZ
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connector D7 terminal 10, D8 terminal 19 and
ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between main power window and door lock/ unlock switch connector D8 terminal 17 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Repair or replace harness.
3. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM and main power window and door lock/unlock switch.
3. Check continuity between BCM connector and main power win- dow and door lock/unlock switch connectors.
4. Check continuity between BCM and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness. 10 - Ground
: Battery voltage
19 - Ground : Battery voltage
LIIA2297E
17 - Ground : Continuity should exist.
LIIA0392E
Connector
Terminal Connector
Terminal Continuity
AB
BCM: M20 68
Main power window and
door lock/unlock switch:
D7 10 Yes
69 C
19 Yes
Main power window and
door lock/unlock switch: D8
Connector Terminal
GroundContinuity
A
BCM: M20 68
No
69 No
LIIA2215E

POWER WINDOW SYSTEMGW-39
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M20 terminals 68, 69 and ground.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace BCM.
Power Window and Door Lock/Unlock Switch RH Power Supply and Ground
Circuit Check
EIS005Y0
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between power window and door lock/unlock switch RH connector D105 terminal 10 and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 11 and ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Repair or replace harness.
3. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between BCM connector M20 (A) terminal 69 and power window and door lock/unlock switch RH connector
D105 (B) terminal 10.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness. 68 - Ground
: Battery voltage
69 - Ground : Battery voltage
LIIA0917E
10 - Ground : Battery voltage
LIIA1257E
11 - Ground: Continuity should exist.
LIIA1258E
69 - 10 : Continuity should exist.
LIIA2298E

GW-40
POWER WINDOW SYSTEM
Revision: November 20092006 QX56
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M20 terminal 69 and ground.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace BCM. Refer to BCS-20, "
BCM" .
Front Power Window Motor LH Circuit CheckEIS005Y1
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connector D7 terminals 8, 11 and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace main power window and door lock/unlock switch. Refer to EI-32, "
REMOVAL" .
2. CHECK POWER WINDOW MOTOR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and front power window motor LH.
3. Check continuity between main power window and door lock/ unlock switch connector D7 terminals 8, 11 and front power win-
dow motor LH connector D9 terminals 1, 2.
OK or NG
OK >> Replace front power window motor LH.
NG >> Repair or replace harness. Refer to GW-66, "
FRONT DOOR GLASS REGULATOR" .
69 - Ground
: Battery voltage
WIIA0508E
ConnectorTerminals
ConditionVoltage (V)
(Approx.)
(+) (-)
D7 8
Ground UP Battery voltage
DOWN 0
11 UP
0
DOWN Battery voltage
LIIA0317E
8 - 2 : Continuity should exist.
11 - 1 : Continuity should exist.
LIIA1260E

POWER WINDOW SYSTEMGW-41
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
Front Power Window Motor RH Circuit CheckEIS005Y2
1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL
1. Connect power window and door lock/unlock switch RH.
2. Turn ignition switch ON.
3. Check voltage between power window and door lock/unlock switch RH connector D105 terminals 8, 9 and ground.
OK or NG
OK >> GO TO 2.
NG >> Replace power window and door lock/unlock switch RH. Refer to EI-32, "
REMOVAL" .
2. CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window motor RH and power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D105 terminals 8, 9 and front power win-
dow motor RH connector D104 terminals 1, 2.
OK or NG
OK >> Replace front power window motor RH. Refer to GW-66,
"FRONT DOOR GLASS REGULATOR" .
NG >> Repair or replace harness.
Limit Switch Circuit Check Front LHEIS005Y3
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH LIMIT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connector D7 termimal 9 and ground.
OK or NG
OK >> Limit switch circuit is OK.
NG >> GO TO 2.
Connector Terminals
ConditionVoltage (V)
(Approx.)
(+) (-)
D105 9
Ground UP
0
DOWN Battery voltage
8 UP Battery voltage
DOWN 0
LIIA1261E
8 - 2 : Continuity should exist.
9 - 1 : Continuity should exist.
LIIA1262E
ConnectorTerminal
Condition Voltage (V)
(Approx.)
(+) (-)
D7 9 Ground Front power window LH is
between fully-open and just
before fully-closed position
(ON)
0
Front power window LH is
between just before fully-
closed position and fully-
closed position (OFF) 5
LIIA0339E

GW-42
POWER WINDOW SYSTEM
Revision: November 20092006 QX56
2. CHECK FRONT POWER WINDOW MOTOR LH LIMIT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor LH connector D9 terminal 5 and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK LIMIT SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between front power window motor LH connec- tor D9 terminal 6 and ground.
OK or NG
OK >> Replace front power window motor LH. Refer to GW-66,
"FRONT DOOR GLASS REGULATOR" .
NG >> GO TO 4.
4. CHECK HARNESS CONTINUITY
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between front power window motor LH connec- tor D9 terminal 6 and main power window and door lock/unlock
switch connector D7 terminal 2.
OK or NG
OK >> Replace main power window and door lock/unlock switch. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness.
5. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between front power window motor LH connec- tor D9 terminal 5 and main power window and door lock/unlock
switch connector D7 terminal 9.
OK or NG
OK >> Replace main power window and door lock/unlock switch. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness. 5 - Ground : Approx. 5V
LIIA0922E
6 - Ground
: Continuity should exist.
LIIA0923E
6 - 2: Continuity should exist.
LIIA0924E
5 - 9: Continuity should exist.
LIIA0925E

POWER WINDOW SYSTEMGW-43
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
Limit Switch Circuit Check Front RHEIS005Y4
1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH LIMIT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between power window motor RH connector D105 terminal 15 and ground.
OK or NG
OK >> Limit switch circuit is OK.
NG >> GO TO 2.
2. CHECK FRONT POWER WINDOW MOTOR RH LIMIT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front power window motor RH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor RH connector D104 terminal 5 and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK LIMIT SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between front power window motor RH con- nector D104 terminal 6 and ground.
OK or NG
OK >> Replace front power window motor RH. Refer to GW-66,
"FRONT DOOR GLASS REGULATOR" .
NG >> GO TO 4.
Connector Te r m i n a l s
Condition Voltage (V)
(Approx.)
(+) (-)
D105 15 Ground Front power window RH is
between fully-open and just
before fully-closed position
(ON)
0
Front power window RH is
between just before fully-
closed position and fully-
closed position (OFF) 5
LIIA1263E
5 - Ground
: Approx. 5V
LIIA0922E
6 - Ground: Continuity should exist.
LIIA0923E

GW-44
POWER WINDOW SYSTEM
Revision: November 20092006 QX56
4. CHECK HARNESS CONTINUITY
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between front power window motor RH con- nector D104 terminal 6 and power window and door lock/unlock
switch RH connector D105 terminal 3.
OK or NG
OK >> Replace power window and door lock/unlock switch RH. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness.
5. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 15 and front power window
motor RH connector D104 terminal 5.
OK or NG
OK >> Replace power window and door lock/unlock switch RH. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness.
Encoder Circuit Check Front LHEIS005Y5
1. CHECK FRONT POWER WINDOW MOTOR LH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor LH connector D9 terminal 4 and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between front power window motor LH connec- tor D9 terminal 4 and main power window and door lock/unlock
switch connector D7 terminal 15.
OK or NG
OK >> Replace main power window and door lock/unlock switch. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness. 6 - 3 : Continuity should exist.
LIIA1264E
15 - 5
: Continuity should exist.
LIIA1265E
4 - Ground: Approx. 10V
WIIA0513E
4 - 15 : Continuity should exist.
LIIA0936E

POWER WINDOW SYSTEMGW-45
C
DE
F
G H
J
K L
M A
B
GW
Revision: November 2009 2006 QX56
3. CHECK ENCODER GROUND
1. Turn ignition switch OFF.
2. Check continuity between front power window motor LH connec- tor D9 terminal 6 and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK ENCODER GROUND CIRCUIT
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between front power window motor LH connec- tor D9 terminal 6 and main power window and door lock/unlock
switch connector D7 terminal 2.
OK or NG
OK >> Replace main power window and door lock/unlock switch. Refer to EI-32, "
REMOVAL" .
NG >> Repair or replace harness.
5. CHECK ENCODER SIGNAL
1. Connect front power window motor LH.
2. Turn ignition switch ON.
3. Check the signal between main power window and door lock/ unlock switch connector and ground with oscilloscope.
OK or NG
OK >> Replace main power window and door lock/unlock switch. Refer to EI-32, "REMOVAL" .
NG >> GO TO 6. 6 - Ground
: Continuity should exist.
LIIA0923E
6 - 2: Continuity should exist.
LIIA0924E
Connec-
tor Terminals
Condition Signal
(+) (-)
D7 13 Ground Opening
LIIA0364E
OCC3383D