lock INFINITI QX56 2006 Factory Service Manual

HOODBL-15
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
INSTALLATION
1. Pull the hood lock cable through the dash lower hole into the engine room.
Be careful not to bend the cable too much, keeping the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the positioning grommet, and push the grommet into the dash lower hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the primary and secondary cables securely to the hood lock.
5. Install the hood lock and the secondary hood lock release assemblies.
6. Check the hood lock adjustment and hood opener operation. Refer to BL-12, "
Fitting Adjustment" .
Hood Lock Control InspectionEIS004QA
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to EI-17, "
FRONT GRILLE" .
2. Make sure the secondary latch is properly engaged with the sec- ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply “body grease ” to the points shown in the figure.
5. Install the front grille. Refer to EI-17, "
FRONT GRILLE" .
PIIA0173E
PIIA0174E
PIIA1086E
PIIA0176E

BL-16
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56
POWER DOOR LOCK SYSTEMPFP:24814
Component Parts and Harness Connector LocationEIS005Z7
WIIA0585E

POWER DOOR LOCK SYSTEMBL-17
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
System DescriptionEIS005Z8
Power is supplied at all times

through 50A fusible link (letter f, located in the fuse and fusible link box)

to BCM terminal 70

through 15A fuse [No. 22, located in the fuse block (J/B)]

to BCM terminal 57

through 10A fuse [No. 19, located in the fuse block (J/B)]

to key switch and key lock solenoid terminal 3.
With ignition key inserted, power is supplied

through key switch and key lock solenoid terminal 4

to BCM terminal 37.
Ground is supplied to terminal 67 of BCM through body grounds M57, M61 and M79.
When the door is locked or unlocked with main power window and door lock/unlock switch, ground is supplied

to CPU of main power window and door lock/unlock switch

through main power window and door lock/unlock switch terminal 17

through grounds M57, M61 and M79.
Then main power window and door lock/unlock switch operation signal is supplied

to BCM terminal 22

through main power window and door lock/unlock switch terminal 14.
When the door is locked or unlocked with power window and door lock/unlock switch RH, ground is supplied

to CPU of power window and door lock/unlock switch RH

through power window and door lock/unlock switch RH terminal 11

through grounds M57, M61 and M79.
Then power window and door lock/unlock switch RH operation signal is supplied

to BCM terminal 22

through power window and door lock/unlock switch RH terminal 16.
When the door is locked with front door lock assembly LH (key cylinder switch), ground is supplied

to main power window and door lock/unlock switch terminal 4

through front door lock assembly LH (key cylinder switch) terminals 1 and 5

through grounds M57, M61 and M79.
Then front door lock assembly LH (key cylinder switch) operation signal is supplied

to BCM terminal 22

through main power window and door lock/unlock switch terminal 14.
When the door is unlocked with front door lock assembly LH (key cylinder switch), ground is supplied

to main power window and door lock/unlock switch terminal 6

through front door lock assembly LH (key cylinder switch) terminals 6 and 5

through grounds M57, M61 and M79.
Then front door lock assembly LH (key cylinder switch) operation signal is supplied

to BCM terminal 22

through main power window and door lock/unlock switch terminal 14.
BCM is connected to main power window and door lock/unlock switch and power window and door lock/unlock
switch RH through a bus.
When the front door switch LH is ON (door is open), ground is supplied

to BCM terminal 47

through front door switch LH terminal 2

through front door switch LH case ground.
When the front door switch RH is ON (door is open), ground is supplied

to BCM terminal 12

through front door switch RH terminal 2

BL-18
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56

through front door switch RH case ground.
When the rear door switch LH is ON (door is open), ground is supplied

to BCM terminal 48

through rear door switch LH terminal 2

through rear door switch LH case ground.
When the rear door switch RH is ON (door is open), ground is supplied

to BCM terminal 13

through rear door switch RH terminal 2

through rear door switch RH case ground.
When the back door latch (door ajar switch) is ON (door is open), ground is supplied

to BCM terminal 43

through back door latch (door ajar switch) terminal 7

through back door latch (door ajar switch) terminal 8

through grounds B7 and B19.
OUTLINE
NOTE:
The glass hatch switch will be operational only when the front door lock actuator RH is in the unlock position.
Functions available by operating the door lock and unlock switches on driver door and pas-
senger door

Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors and
glass hatch actuator are locked.

Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors
and glass hatch actuator are unlocked.
Functions available by operating the front door lock assembly LH (key cylinder switch)

Interlocked with the locking operation of door key cylinder, door lock actuators of all doors are locked.

When door key cylinder is unlocked, front door lock assembly LH (actuator) is unlocked.

When door key cylinder is unlocked for the second time within 5 seconds after the first operation, door
lock actuators on all doors are unlocked.
Key reminder door system
When door lock and unlock switch is operated to lock doors with ignition key in key cylinder and any door
open, all door lock actuators are locked and then unlocked.

POWER DOOR LOCK SYSTEMBL-19
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
SchematicEIS005Z9
WIWA1534E

BL-20
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56
Wiring Diagram — D/LOCK —EIS005ZA
WIWA0742E

POWER DOOR LOCK SYSTEMBL-21
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
WIWA1536E

BL-22
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56
LIWA0418E

POWER DOOR LOCK SYSTEMBL-23
C
DE
F
G H
J
K L
M A
B
BL
Revision: November 2009 2006 QX56
WIWA1306E

BL-24
POWER DOOR LOCK SYSTEM
Revision: November 20092006 QX56
WIWA2209E