ignition INFINITI QX56 2008 Factory Workshop Manual

LIFTING SWITCH (REAR)ADP-53
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK LIFTING SWITCH (REAR)
Refer to ADP-53, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace power seat switch LH.
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace driver seat control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735482
1. CHECK LIFTING SWITCH (REAR)
1. Turn ignition switch OFF.
2. Disconnect power seat switch LH.
3. Check continuity between power seat switch LH terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch LH.
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 14
No
29
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 14
Ground Battery voltage
29
PIIA4586E
Te r m i n a l Condition Continuity
Power seat switch LH
3 2 Lifting switch rear (up)
Operate Yes
Release No
8 Lifting switch rear (down) Operate Yes
Release No
LIIA1132E
Revision: March 2010
2008 QX56

ADP-54
< COMPONENT DIAGNOSIS >
TILT SWITCH
TILT SWITCH
DescriptionINFOID:0000000001754039
ADP steering switch is equipped to the steering column. The operation signal is input to the automatic drive
positioner control unit when the ADP steering switch is operated.
Component Function CheckINFOID:0000000001754040
1.CHECK FUNCTION
1. Select “TILT SW-UP”, “TILT SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check tilt switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-54, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001754041
1. CHECK ADP STEERING SWITCH SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2. CHECK ADP STEERING SWITCH HARNESS CONTINUITY
1. Disconnect automatic drive positioner control unit connector and ADP steering switch.
2. Check continuity between automat ic drive positioner control unit
connector M33 terminals 1, 17 and ADP steering switch connec-
tor M16 terminals 2, 3.
3. Check continuity between automatic drive positioner control unit connector M33 terminals 1, 17 and ground.
Monitor item ConditionStatus
TILT SW-UP Tilt switch (up) Operate
ON
Release OFF
TILT SW-DN Tilt switch (down) Operate
ON
Release OFF
ConnectorTe r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (-)
M33 1
Ground ADP steering switch ON (UP
operation)
0
Other than above 5
17 ADP steering switch ON
(DOWN operation)
0
Other than above 5
LIIA0491E
1 - 2: Continuity should exist.
17 - 3 : Continuity should exist.
LIIA1434E
Revision: March 2010 2008 QX56

ADP-56
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
PEDAL ADJUSTING SWITCH
DescriptionINFOID:0000000001735483
Pedal adjusting switch is on the instrument panel. The operation signal is input to the driver seat control unit
when the pedal adjusting switch is operated. The pedal adjus ting switch signal is sent to the automatic drive
positioner control unit via UART communication.
Component Function CheckINFOID:0000000001735484
1. CHECK FUNCTION
1. Select “PEDAL SW-FR”, “PEDAL SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check pedal adjusting switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-56, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735485
1. CHECK PEDAL ADJUSTING SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between driver seat control unit harness connec- tor and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK PEDAL ADJUSTING SWITCH CIRCUIT
Monitor item ConditionStatus
PEDAL SW-FR Pedal adjusting switch (forward) Operate
ON
Release OFF
PEDAL SW-RR Pedal adjusting switch (backward) Operate
ON
Release OFF
Driver seat
control unit connector Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+) (–)
B202 15
Ground Pedal ad-
justing switch Operate
(backward) 0
Release Battery
voltage
30 Operate
(forward) 0
Release Battery
voltage
PIIA4591E
Revision: March 2010 2008 QX56

PEDAL ADJUSTING SWITCHADP-57
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and pedal adjusting switch.
3. Check continuity between driver seat control unit harness con- nector and pedal adjusting switch harness connector.
4. Check continuity between driver seat control unit harness con- nector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DRIVER SEAT CONTROL UNIT OUTPUT
1. Connect the driver seat control unit.
2. Turn ignition switch ON.
3. Check voltage between driver s eat control unit harness connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace driver seat control unit.
4. CHECK PEDAL ADJUSTING SWITCH
Refer to ADP-58, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5
NO >> Replace pedal adjusting switch.
5. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> Replace or replace harness.
6. CHECK INTERMITTENT INCIDENT
Driver seat
control unit
connector Te r m i n a l
Pedal adjusting
switch connector Terminal Continuity
B202 15
M96 2
Ye s
30 3
Driver seat control unit connector Te r m i n a l
GroundContinuity
B202 15
No
30
LIIA0726E
Driver seat control unit
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
B202 15
Ground Battery voltage
30
PIIA4591E
1 - Ground : Continuity should exist.
LIIA1015E
Revision: March 2010 2008 QX56

ADP-58
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SWITCH
Refer to GI-38, "Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735486
1.CHECK PEDAL ADJUSTING SWITCH
1. Turn ignition switch OFF.
2. Disconnect pedal adjusting switch.
3. Check continuity between pedal adjusting switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace pedal adjusting switch.
Te r m i n a l ConditionContinuity
Pedal adjusting switch
1 2
Pedal adjusting switch
(forward) Operate
Yes
Release No
3 Pedal adjusting switch
(backward) Operate
Yes
Release No
LIIA1014E
Revision: March 2010 2008 QX56

SEAT MEMORY SWITCHADP-59
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY SWITCH
DescriptionINFOID:0000000001735487
Memory switch is equipped on the seat memory switch installed to the front door LH trim. The operation signal
is input to the automatic drive positioner control unit when the memory switch is operated.
Component Function CheckINFOID:0000000001735488
1. CHECK FUNCTION
1. Select “MEMORY SW 1”, “MEMORY SW 2”, "SET SW" in “Data monitor” mode with CONSULT-III.
2. Check seat memory switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-59, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000001735489
1. CHECK MEMORY SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and seat memory switch.
3. Check continuity between automat ic drive positioner control unit
harness connector and seat memo ry switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK MEMORY SWITCH GROUND CIRCUIT
Monitor item ConditionStatus
MEMORY SW1 Memory switch 1 Push
ON
Release OFF
MEMORY SW2 Memory switch 2 Push
ON
Release OFF
SET SW Set switch Push
ON
Release OFF
Automatic drive
positioner control unit connector Te r m i n a l
Seat memory
switch connector Terminal Continuity
M33 9
D5 1
Ye s
24 3
25 2
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 9
No
24
25
PIIA4576E
Revision: March 2010 2008 QX56

ADP-60
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
Check continuity between seat memory switch harness connector
and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK SEAT MEMORY SWITCH
Refer to ADP-60, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace seat memory switch.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000001735490
1.CHECK SEAT MEMORY SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat memory switch.
3. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace seat memory switch.
Seat memory switch connector Te r m i n a l
GroundContinuity
D5 4 Yes
PIIA4821E
Te r m i n a l
Condition Continuity
Seat memory switch
4 1 Memory switch 1
Push
Yes
Release No
2 Memory switch 2 Push
Yes
Release No
3 Set switch Push
Yes
Release No
LIIA1020E
Revision: March 2010 2008 QX56

DOOR MIRROR REMOTE CONTROL SWITCHADP-61
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : DescriptionINFOID:0000000001735491
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Comp onent Function CheckINFOID:0000000001735492
1. CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Refer to ADP-26, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Changeover switch function is OK.
NO >> Refer to ADP-61, "
CHANGEOVER SWITCH : Diagnosis Procedure".
CHANGEOVER SWITCH : Diagnosis ProcedureINFOID:0000000001735493
1. CHECK CHANGEOVER SWITCH SIGNAL
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir- ror remote control switch.
3. Check continuity between automat ic drive positioner control unit
connector and door mirror remote control switch connector.
4. Check continuity between automatic driv e positioner control unit connector and ground.
Te r m i n a l s
Change over switch condition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control unit connector Terminal
M33 2
Ground RIGHT
0
Other than above 5
18 LEFT
0
Other than above 5
PIIA4767E
Automatic drive
positioner control unit connector Te r m i n a lDoor mirror re-
mote control
switch connector Terminal Continuity
M33 (A) 2
D10 (B) 11
Ye s
18 10
ALJIA0201ZZ
Revision: March 2010 2008 QX56

ADP-62
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
Check continuity between door mirro r remote control switch connec-
tor and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace automatic drive positioner control unit.
5. CHECK CHANGEOVER SWITCH
Check changeover switch.
Refer to ADP-62, "
CHANGEOVER SWITCH : Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-38, "Intermittent Incident".
NO >> Replace door mirror remote control switch.
6. CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace the malfunctioning parts.
CHANGEOVER SWITCH : Component InspectionINFOID:0000000001735494
1. CHECK CHANGEOVER SWITCH
Automatic drive positioner control
unit connector Te r m i n a l
GroundContinuity
M33 (A) 2
No
18
Door mirror remote control switch
connector Terminal
GroundContinuity
D10 7 Yes
ALJIA0189ZZ
Te r m i n a l s
Voltage (V)(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector Te r m i n a l
M33 2
Ground 5
18
PIIA4767E
Revision: March 2010 2008 QX56

DOOR MIRROR REMOTE CONTROL SWITCHADP-63
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Check door mirror remote control switch.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace door mirror remote control switch.
MIRROR SWITCH
MIRROR SWITCH : DescriptionINFOID:0000000001735495
It operates angle of the door mirror face.
It transmits mirror face adjust operation to automatic drive positioner control unit.
MIRROR SWITCH : Component Function CheckINFOID:0000000001735496
1. CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “M IR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Refer to ADP-26, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Mirror switch function is OK.
NO >> Refer to ADP-63, "
MIRROR SWITCH : Diagnosis Procedure".
MIRROR SWITCH : Diagnosis ProcedureINFOID:0000000001735497
1. CHECK MIRROR SWITCH FUNCTION
1. Turn ignition switch ON.
2. Check voltage between automatic drive positioner control unit
connector and ground.
Is the inspection result normal?
YES >> GO TO 6
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
Te r m i n a l Change over switch
condition Continuity
Door mirror remote control switch
10 7LEFT
Yes
Other than above No
11 RIGHT
Yes
Other than above No
ALJIA0272ZZ
Te r m i n a l s
Mirror switchCondition Voltage (V)
(Approx.)
(+)
(–)
Automatic drive
positioner control unit connector Te r m i n a l
M33 3
Ground UP
0
Other than above 5
4 LEFT
0
Other than above 5
19 DOWN
0
Other than above 5
20 RIGHT
0
Other than above 5
PIIA4771E
Revision: March 2010 2008 QX56