instrument panel INFINITI QX56 2009 Factory User Guide

AV
NAVIGATION SYSTEMAV-17
< FUNCTION DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Component DescriptionINFOID:0000000003776775
10. Rear audio remote control unit R204 11. Microphone R109 12. Front door speaker
LH D12
RH D112
13. Rear door tweeter LH D208
RH D308 14. Rear door speaker
LH D207
RH D307 15. Back door speaker
LH D518
RH D716
16. Subwoofer B72 (under driver’s seat) 17. BOSE speaker amp M112, M113 (view behind instrument panel above
accelerator pedal)18. Rear view camera
control unit B73
(located behind luggage finisher LHl)
19. Rear view camera D504
Part name Description
AV c o n t r o l u n i t • Controls each operation of the navigation system
• HDD is built in
• Voice guidance signal is output to BOSE speaker amp.
BOSE speaker amp. Voice guidance signal is input from AV control unit, and it is output to speakers.
Front tweeter Voice guidance signal from BOSE speaker amp. is output.
Steering switches • Each operation of navigation system can be performed
• Switch operating signal is output to AV control unit
Microphone Sends voice signals to AV control unit
GPS antenna GPS signal is received and is output to AV control unit.
Revision: December 20092009 QX56

AV-20
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
REAR VIEW MONITOR SYSTEM
Component Description
INFOID:0000000003776779
10. Rear audio remote control unit R204 11. Microphone R109 12. Front door speaker
LH D12
RH D112
13. Rear door tweeter LH D208
RH D308 14. Rear door speaker
LH D207
RH D307 15. Back door speaker
LH D518
RH D716
16. Subwoofer B72 (under driver’s seat) 17. BOSE speaker amp M112, M113 (view behind instrument panel above
accelerator pedal)18. Rear view camera control unit B73
(located behind luggage finisher LHl)
19. Rear view camera D504
Part name Description
AV control unit Communication signal is sent from rear view camera control unit
Rear view camera control unit • Receives reverse signal from back-up lamp relay
• Receives rear view camera image signal
• Sends camera ON signal to rear view camera
• Sends image signal to display unit
Rear view camera • Receives camera ON signal from rear view camera control unit
• Sends image signal to rear view camera control unit
Display unit Recieves and displays image signal from rear view camera control unit
Revision: December 20092009 QX56

AV-26
< FUNCTION DIAGNOSIS >[AUDIO SYSTEM]
HANDS-FREE PHONE SYSTEM
Component Description
INFOID:0000000003776787
10. Rear audio remote control unit R204 11. Microphone R109 12. Front door speaker
LH D12
RH D112
13. Rear door tweeter LH D208
RH D308 14. Rear door speaker
LH D207
RH D307 15. Back door speaker
LH D518
RH D716
16. Subwoofer B72 (under driver’s seat) 17. BOSE speaker amp M112, M113 (view behind instrument panel above
accelerator pedal)18. Rear view camera control unit B73
(located behind luggage finisher LHl)
19. Rear view camera D504
Part name Description
AV control unit • Receives telephone voice signal from Antenna and Microphone
• Sends telephone voice and voice guidance signals to the speakers
BOSE speaker amp. • Recieves audio signals from the AV control unit
• Outputs amplified audio signals to the speakers.
Front door speaker Receives telephone voice and voice guidance signals from the AV control unit
through the BOSE speaker amp.
Front tweeter
Center speaker
Steering switches • Start a voice recognition session
• Answer and end telephone calls
• Adjust the volume level
Microphone Sends voice signals to Bluetooth control unit
Bluetooth antenna Sends telephone voice signal to Bluetooth control unit
Revision: December 20092009 QX56

AV-158
< SYMPTOM DIAGNOSIS >[AUDIO SYSTEM]
NORMAL OPERATING CONDITION
Destination, Passing Points and Menu Items Cannot be Selected/Set
Symptom
Cause Remedy
Map screen and BIRDVIEW™
Name of the place vary with the
screen. Some thinning of the character data is done to pre-
vent the display becoming to complex. In some
cases and in some locations, the display contents
may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing. System is not malfunctioning.
Vehicle mark is not positioned cor-
rectly. Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF. Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON. The daytime screen is selected by the “SWITCH
SCREENS” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screen may
be inhibited by the automatic illumination adjust-
ment function. Perform screen dimming and select the
nighttime screen by “SWITCH SCREENS”.
Map screen will not scroll in accor-
dance with the vehicle travel. Current location is not displayed.
Press “MAP” button to display the current lo-
cation.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP” button to display the current lo-
cation.
Accuracy indicator (GPS satellite
mark) on the map screen stays
gray. GPS satellite signal is intercepted because the ve-
hicle is in or behind a building.
Move the vehicle out to an open space.
GPS satellite signal cannot be received because
an obstacle is placed on top of the instrument pan-
el. Do not place anything on top of the meter dis-
play (instrument panel).
GPS satellites are not visible from current location. Wait until GPS satellites are visible by mov- ing the vehicle.
Vehicle location accuracy is low. Accuracy indicator (GPS sate llite mark) on the
map screen stays gray. Current location is not determined.
Vehicle speed setting by the vehicle speed pulse
has been deviated (advanced or retarded) from
the actual vehicle speed because tire chain is fit-
ted or the system has been used on another vehi-
cle. Drive the vehicle for a while [for approx. 30
minutes at approx. 30 km/h (19 MPH)] and
the deviation will be automatically adjusted. If
advancement or retard still occur, perform
the distance adjustment by CONFIRMA-
TION/ADJUSTMENT mode of diagnosis
function.
Map data has error or omission. (Vehicle mark is
always deviated to the same position.) As a rule, an updated map DVD–ROM will be
released once a year.
Symptom
Cause Remedy
Destination cannot be set. Destination to be set is on an expressway. Set the destination on an ordinary road.
Passing point is not searched
when re-searching the route. The vehicle has already passed the passing point,
or the system judged so. To include the passing points that have been
passed into the route again, set the route
again.
Route information will not be dis-
played. Route searching has not been done.
Set the destination and perform route
searching.
Vehicle mark is not on the recommended route. Drive on the recommended route.
Route guide is turned OFF. Turn route guide ON.
Route information is not available on the dark pink
route. System is not malfunctioning.
After the route searching, no guide
sign will appear as the vehicle
goes near the entrance/exit to the
toll road. Vehicle mark is not on the recommended route.
(On the display, only guide signs related to the rec-
ommended route will be shown.)
Drive on the recommended route.
Revision: December 20092009 QX56

AV-170
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
DISPLAY UNIT
DISPLAY UNIT
Removal and InstallationINFOID:0000000003776903
REMOVAL
1. Remove cluster lid C. Refer to
IP-16, "Removal and Installation".
2. Remove the display unit screws (A), pull out the display unit (1) from instrument panel, to disconnect the display unit connectors.
3. Remove the A/C auto amp. screws (A) and the A/C auto amp. (1).
• Display unit (2)
4. Remove the display unit bracket screws and the display unit brackets.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0272ZZ
ALIIA0063ZZ
Revision: December 20092009 QX56

AV
FRONT TWEETERAV-171
< ON-VEHICLE REPAIR > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
FRONT TWEETER
Removal and InstallationINFOID:0000000003776904
REMOVAL
CAUTION:
Use a suitable tool to prevent damage to the tweet er speaker grille trim and the instrument panel.
1. Remove front tweeter speaker grille.
2. Remove the front tweeter clips (C103) (A).
3. Disconnect the front tweeter connector.
4. Remove the front tweeter (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0202ZZ
Revision: December 20092009 QX56

AV-172
< ON-VEHICLE REPAIR >[AUDIO SYSTEM]
CENTER SPEAKER
CENTER SPEAKER
Removal and InstallationINFOID:0000000003776905
REMOVAL
CAUTION:
Use a suitable tool to prevent
damage to the center speaker grille and the instrument panel.
1. Using a suitable tool, remove the center speaker grille finisher (1).
2. Disconnect the center speaker connector (A).
3. Remove the center speaker screws (B).
4. Remove the center speaker (2).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0275ZZ
Revision: December 20092009 QX56

BCS-6
< FUNCTION DIAGNOSIS >[BCM]
BODY CONTROL SYSTEM
Component Parts Location
INFOID:0000000003776378
 BCM M18, M19, M20 (view wit h instrument panel removed)
LEIA0068E
Revision: December 20092009 QX56

BRAKE PEDALBR-19
< ON-VEHICLE REPAIR >
C
DE
G H
I
J
K L
M A
B
BR
N
O P
ON-VEHICLE REPAIR
BRAKE PEDAL
Removal and InstallationINFOID:0000000004042331
REMOVAL
CAUTION:
• Before removal and installation, the accelerator and brake pedals must be in the forward most posi-
tion (closest to the floor). This is to align th e base position of the accelerator and brake pedals.
• Do not disassemble the brake pedal adjusting mechanism.
• Avoid damage from dropping the brake pedal assembly during handling.
• Keep the brake pedal assembly away from water.
1. Remove the lower instrument panel LH. Refer to IP-17, "
Removal and Installation".
2. Remove the stop lamp switch and ASCD cancel switch from the pedal assembly.
1. Brake pedal assembly 2. Snap pin3. Clip
4. Stop lamp switch 5. Pedal pad6. Clevis pin
7. ASCD cancel switch
WFIA0232E
Revision: December 20092009 QX56

BR-26
< ON-VEHICLE REPAIR >
BRAKE BOOSTER
BRAKE BOOSTER
Removal and InstallationINFOID:0000000005890851
CAUTION:
• Be careful not to deform or bend brake piping while removing and installing brake booster.
• Replace clevis pin if it is damaged.
• Be careful not to damage brake booster stud bolt threads. If brake booster is tilted or inclined during
installation, dash panel may damage the threads.
• Attach the check valve in the correct direction.
REMOVAL
1. Remove air duct and resonator assembly. Refer to EM-25, "Removal and Installation".
2. Remove cowl top extension. Refer to EXT-18, "
Removal and Installation".
3. Remove master cylinder assembly from brake booster. Refer to BR-25, "
Removal and Installation".
4. Remove vacuum hose from brake booster. Refer to BR-28, "
Removal and Installation".
5. Disconnect active booster harness connector and delta stroke sensor harness connectors from brake booster.
6. Remove the instrument lower panel LH. Refer to IP-12, "
Exploded View".
7. Remove brake pedal to clevis attachment snap pin and clevis pin from inside the vehicle.
8. Remove brake booster to brake pedal assembly nuts.
9. Reposition the A/C line out of the way.
10. Remove brake booster and spacer block from dash panel.
INSPECTION AFTER REMOVAL
Output Rod Length Inspection
1. Reservoir tank 2. Master cylinder assembly3. Gasket
4. Brake pedal 5. Lock nut 6. Spacer block
7. Brake booster 8. Active booster harness connector 9. Delta stroke sensor
AWFIA0416GB
Revision: December 20092009 QX56