battery INFINITI QX56 2009 Factory Repair Manual

AV
DISPLAY UNITAV-145
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
DISPLAY UNIT
Reference ValueINFOID:0000000003776894
TERMINAL LAYOUT
PHYSICAL VALUES
ALNIA0666GB
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(B) Ground Ground
—Ignition
switch ON —0
V
2
(Y) Ground Battery power supply Input Ignition
switch
OFF —1
2V
3
(V) Ground ACC power supply
InputIgnition
switch ACC —1
2V
4—Shield —— — —
5
(L) Ground DVD player image ground — Ignition
switch ON —0
V
6
(B) Ground RGB signal (G: green) Input Ignition
switch ON Start confirmation/adjust-
ment mode, and then dis-
play color bar by
selecting“Color Spectrum
Bar” on DISPLAY DIAGNO-
SIS screen.
7—Shield —— — —
8
(W/L) Ground
Horizontal synchronizing
(HP) signal OutputIgnition
switch
ON —
SKIB2236J
SKIB3601E
Revision: December 20092009 QX56

AV
BOSE SPEAKER AMPAV-149
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P8
(W/B) 13
(L/B) Audio signal front door
speaker and tweeter RH
OutputIgnition
switch ON Audio output
9
(W) 14
(B) Audio signal subwoofer Output Ignition
switch ON Audio output
11
(Y) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
12
(B) Ground Ground
—Ignition
switch ON —0
V
15
(V) 28
(R) Audio signal center speak-
er
OutputIgnition
switch ON Audio output
18
(LG) 32
(V) Audio signal front LH Input Ignition
switch
ON Audio input
19
(BR) 20
(B/R) Audio signal front RH Input Ignition
switch ON Audio input
21
(L) 22
(B/W) Audio signal rear LH Input Ignition
switch ON Audio input
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
Revision: December 20092009 QX56

AV-150
< ECU DIAGNOSIS >[AUDIO SYSTEM]
BOSE SPEAKER AMP
23
(W) 33
(B) Audio signal rear RH Input Ignition
switch ON Audio input
25
(W/G) Ground Subwoofer amp. ON signal Output Ignition
switch ACC —
Battery voltage
31
(GR/L) Ground Amp. ON signal
InputIgnition
switch
ACC —
Battery voltage
37
(W/R) 27
(L) Audio signal back door
speaker RH
InputIgnition
switch
ON Audio input
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB3609E
Revision: December 20092009 QX56

AV
REAR VIEW CAMERA CONTROL UNITAV-151
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
REAR VIEW CAMERA CONTROL UNIT
Reference ValueINFOID:0000000003776896
TERMINAL LAYOUT
PHYSICAL VALUES
WKIA5224E
Te r m i n a l
(wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(Y) Ground Battery power
InputIgnition
switch
OFF —
Battery voltage
2
(V) Ground ACC power
InputIgnition
switch ACC —
Battery voltage
3
(B) Ground Ground
—Ignition
switch
ON —0
V
4
(G/W) Ground Reverse signal input
InputIgnition
switch ON A/T selector lever R
position
Battery voltage
A/T selector lever in
other than R position 0V
5
(BR) Ground AV Control
OutputIgnition
switch ON —0
V
6
(G/W) Ground DDL
Output ———
8
(Y) Ground Camera power output Output Ignition
switch ON A/T selector lever R
position
6V
9 Ground Camera image input (–) Input Ignition
switch
ON —0
V
10
(G) Ground Camera image input (+) Input Ignition
switch
ON A/T selector lever R
position
SKIA4894E
Revision: December 20092009 QX56

AV
DVD PLAYERAV-153
< ECU DIAGNOSIS > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
DVD PLAYER
Reference ValueINFOID:0000000003776897
PHYSICAL VALUES
ALNIA0665GB
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
1
(W) 2
(B) DVD audio signal LH Output Ignition
switch ON With operation of the DVD
player
3—Shield —— — —
5
(B) Ground Ground
—Ignition
switch
ON —0
V
6
(BR) Ground Illumination control (pulse
width modulated)
— — With lighting switch ON
—
7
(W/L) Ground Can communication Input/
Output Ignition
switch ON ——
9
(SB) Ground Video monitor power sup-
ply OutputIgnition
switch ON With DVD player operation
Battery voltage
10
(G/Y) Ground Switch power
OutputIgnition
switch
ON With DVD player operation
5V
12
(B/W) Ground VTR (+)
OutputIgnition
switch ON With DVD player operation
—
13
(L) Ground VTR (-)
OutputIgnition
switch ON With DVD player operation
—
14
(B/W) Ground Display ground
—Ignition
switch
ON With DVD player operation
0V
16
(Y) — Data receive
Input —— —
SKIB3609E
Revision: December 20092009 QX56

AV-154
< ECU DIAGNOSIS >[AUDIO SYSTEM]
DVD PLAYER
17
(R) 18
(G) DVD audio signal RH Output Ignition
switch ON With DVD player operation
21
(Y) Ground Battery power
Input ——Battery voltage
22
(R/L) Ground Illumination power
Input —With instrument illumination
ON Battery voltage
23
(P/B) Ground CAN communication
Input/
Output Ignition
switch
ON —0
V
24
(V) Ground ACC power
InputIgnition
switch
ACC or
ON —
Battery voltage
25
(BR) Ground Video monitor power Output Ignition
switch ON With DVD player operation
Battery voltage
26
(B/Y) Ground Video monitor ground Input Ignition
switch ON With instrument illumination
ON 0V
28
(B/W) Ground Video out
InputIgnition
switch
ACC or
ON —
30 — Shield — — ——
32
(BR) — Data transmit
Output ———
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB2251J
Revision: December 20092009 QX56

AV
PRECAUTIONSAV-165
< PRECAUTION > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005851882
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Un it or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or el ectric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000005851883
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecti ng both battery cables with the ignition knob in the
″ LOCK ″ position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS , an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
Revision: December 20092009 QX56

AV-166
< PRECAUTION >[AUDIO SYSTEM]
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of a ll control units using CONSULT-III.
Revision: December 20092009 QX56

AV
AV CONTROL UNITAV-169
< ON-VEHICLE REPAIR > [AUDIO SYSTEM]
C
D
E
F
G H
I
J
K L
M B A
O P
Only remove and replace the A/C or AV switch assembly knobs if damaged or missing. The knobs
must not be removed from the switches when removi ng and installing the A/C or AV switch assembly
to prevent damage to the switch assembly.
REMOVAL
1. Disconnect the battery negative terminal.
2. Remove the cluster lid C. Refer to IP-16, "
Removal and Installation".
3. Remove the AV control unit screws, using a power tool.
4. Remove the AV control unit.
5. Remove the A/C and AV switch assembly screws, t hen remove the A/C and AV switch assembles as nec-
essary.
INSTALLATION
Installation is in the reverse order of removal.
Revision: December 20092009 QX56

BCS-2
COMB SW .................................................................24
COMB SW : CONSULT-III Function (BCM -
COMB SW) .............................................................
24
IMMU ...................................................................... ...25
IMMU : CONSULT-III Function (BCM - IMMU) .......25
BATTERY SAVER ................................................. ...25
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) ........................................... ...
25
TRUNK ................................................................... ...26
TRUNK : CONSULT-III Function (BCM - TRUNK) ...26
RETAINED PWR .................................................... ...26
RETAINED PWR : CONSULT-III Function (BCM -
RETAINED PWR) ...................................................
26
SIGNAL BUFFER ................................................... ...26
SIGNAL BUFFER : CONSULT-III Function (BCM
- SIGNAL BUFFER) ................................................
26
AIR PRESSURE MONITOR ................................... ...27
AIR PRESSURE MONITOR : Diagnosis Descrip-
tion ..........................................................................
27
AIR PRESSURE MONITOR : CONSULT-III Func-
tion ..........................................................................
28
THEFT ALM ........................................................... ...29
THEFT ALM : CONSULT-III Function (BCM -
THEFT ALM) ..........................................................
29
COMPONENT DIAGNOSIS ........................30
U1000 CAN COMM CIRCUIT ......................... ...30
Description ........................................................... ...30
DTC Logic ...............................................................30
Diagnosis Procedure ..............................................30
U1010 CONTROL UNIT (CAN) .........................31
DTC Logic ............................................................ ...31
Diagnosis Procedure ..............................................31
Special Repair Requirement ...................................31
POWER SUPPLY AND GROUND CIRCUIT .....32
Diagnosis Procedure ............................................ ...32
COMBINATION SWITCH INPUT CIRCUIT .......33
Diagnosis Procedure ............................................ ...33
Special Repair Requirement ...................................34
COMBINATION SWITCH OUTPUT CIRCUIT ...35
Diagnosis Procedure ...............................................35
Special Repair Requirement ...................................35
COMBINATION SWITCH ..................................36
Description ........................................................... ...36
Diagnosis Procedure ...............................................36
ECU DIAGNOSIS .......................................38
BCM (BODY CONTROL MODULE) ............... ...38
Reference Value .................................................. ...38
Terminal Layout ......................................................40
Physical Values .......................................................40
Wiring Diagram .......................................................46
Fail Safe .................................................................50
DTC Inspection Priority Chart ...............................51
DTC Index ..............................................................51
SYMPTOM DIAGNOSIS ............................53
COMBINATION SWITCH SYSTEM SYMP-
TOMS .............................................................. ...
53
Symptom Table .................................................... ...53
PRECAUTION ............................................54
PRECAUTIONS .............................................. ...54
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. ...
54
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ..................................
54
ON-VEHICLE REPAIR ...............................56
BCM (BODY CONTROL MODULE) ............... ...56
Removal and Installation ...................................... ...56
Revision: December 20092009 QX56