battery INFINITI QX56 2009 Factory Owner's Guide

ADP-104
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
Door mirror RH
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace automatic drive positioner control unit. Refer to ADP-166, "Removal and Installation"
.
4. CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to ADP-104, "Component Inspection"
.
Is the inspection result normal?
YES >> Refer to GI-38, "Intermittent Incident".
NO >> Replace door mirror actuator. Refer to MIR-14, "Mirror Actuator"
.
Component InspectionINFOID:0000000003775642
1. CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to MIR-14, "Exploded View"
.
Is the inspection result normal?
YES >> GO TO 2
NO >> Replace door mirror actuator. Refer to MIR-14, "Mirror Actuator"
.
2. CHECK DOOR MIRROR MOTOR-II
1. Turn ignition switch OFF.
2. Disconnect door mirror.
3. Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace door mirror actuator. Refer to MIR-14, "Mirror Actuator"
.
Te r m i n a l s
Mirror switch con-dition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner con-
trol unit connec-
tor Te r m i n a l
M33 14
GroundUP Battery voltage
Other than above 0
15 LEFT Battery voltage
Other than above 0
30 DOWN / RIGHT Battery voltage
Other than above 0
ALJIA0198ZZ
Door mirror connector Te r m i n a l
Operational direction
(+) (–)
D4 (LH)
D107 (RH) 32 RIGHT
23 LEFT
13 UP
31 DOWN
ALJIA0199ZZ
Revision: December 20092009 QX56

ADP-106
< COMPONENT DIAGNOSIS >
SEAT MEMORY INDICATOR LAMP
Check voltage between seat memory switch harness connector and
ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Check the following.Fuse
 Harness for open or short between memory indicator and fuse.
3. CHECK MEMORY INDICATOR
Refer to ADP-106, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace seat memory switch. Refer to ADP-167, "Removal and Installation"
.
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "Intermittent Incident"
.
Is the inspection result normal?
YES >> Replace automatic drive posit ioner control unit. Refer to ADP-166, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Component InspectionINFOID:0000000003775646
1. CHECK SEAT MEMORY INDICATOR
1. Disconnect seat memory switch.
2. Check continuity between seat memory switch terminals.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace seat memory switch. Refer to ADP-167, "Removal and Installation"
.
Seat memory switch
connector Te r m i n a l s
Voltage (V)
(Approx.)
(+) (–)
D5 5 Ground Battery voltage
PIIA4595E
Te r m i n a l Continuity
Seat memory switch
(+) (-) 6 5Yes
7
ALJIA0200ZZ
Revision: December 20092009 QX56

DRIVER SEAT CONTROL UNITADP-109
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Te r m i n a l Wire
Color Item Condition Voltage (V)
(Approx.)
1 W UART LINE (RX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
3 L/B CAN-H — —
6 R Ignition switch (START) Ignition switch (START position) Battery voltage
9 R/B Reclining motor sensor signal ON (seat reclining motor opera-
tion)
Other than above 0 or 5
10 B/R Rear lifting motor sensor signal ON (rear lifting motor operation)
Other than above 0 or 5
11 Y / R Sliding switch BACKWARD sig-
nal ON (seat sliding switch BACK-
WARD operation)
0
Other than above Battery voltage
12 L/W Reclining switch BACKWARD
signal ON (seat reclining switch BACK-
WARD operation)
0
Other than above Battery voltage
13 V Front lifting switch DOWN signal ON (front lifting switch DOWN op-
eration)
0
Other than above Battery voltage
14 P/L Rear lifting switch DOWN signal ON (rear lifting switch DOWN op-
eration)
0
Other than above Battery voltage
15 SB Pedal adjusting switch BACK-
WARD signal ON (pedal adjusting switch BACK-
WARD operation)
0
Other than above Battery voltage
16 R/W Seat sensor power Ignition switch ON 5
17 Y/R UART LINE (TX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
PIIA4813E
SIIA0692J
SIIA0693J
PIIA4814E
Revision: December 20092009 QX56

ADP-110
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
19 G CAN-L — —
21 LA/T shift selector (park position
switch) signal A/T selector lever in P position 0
A/T selector lever in other than P
position with ignition key in ignition
cylinder
Battery voltage
24 R/L Seat sliding motor sensor signal ON (seat sliding motor operation)
Other than above 0 or 5
25 Y/G Front lifting motor sensor signal ON (front lifting motor operation)
Other than above. 0 or 5
26 L/R Seat sliding switch FORWARD
signal ON (seat sliding switch FOR-
WARD operation)
0
Other than above Battery voltage
27 V/W Seat reclining switch FORWARD
signal ON (seat reclining switch FOR-
WARD operation)
0
Other than above Battery voltage
28 BR/Y Front lifting switch UP signal ON (front lifting switch UP opera-
tion)
0
Other than above Battery voltage
29 G/R Rear lifting switch UP signal ON (rear lifting switch UP opera-
tion)
0
Other than above Battery voltage
30 L/Y Pedal adjusting switch FOR-
WARD signal ON (pedal adjusting switch FOR-
WARD operation)
0
Other than above Battery voltage
31 GR/R Sensor ground — 0
32 G/W Ground — 0
33 W/B Battery power supply — Battery voltage
35 R/G Sliding motor FORWARD output
signal Sliding switch FORWARD opera-
tion (Motor operated)
Battery voltage
Other than above 0
36 L Reclining motor FORWARD out-
put signal Reclining switch FORWARD oper-
ation (Motor operated)
Battery voltage
Other than above 0
37 B Front lifting motor DOWN output
signal Front lifting switch DOWN opera-
tion (Motor operated)
Battery voltage
Other than above 0
Te r m i n a l
Wire
Color Item Condition Voltage (V)
(Approx.)
PIIA3277E
SIIA0691J
Revision: December 20092009 QX56

DRIVER SEAT CONTROL UNITADP-111
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
38 GR Rear lifting motor UP output sig-
nal Rear end lifting switch UP opera-
tion (Motor operated)
Battery voltage
Other than above 0
39 R Rear lifting motor DOWN output
signal Rear end lifting switch DOWN op-
eration (Motor operated)
Battery voltage
Other than above 0
40 G Battery power supply — Battery voltage
42 R/Y Sliding motor BACKWARD out-
put signal Sliding switch BACKWARD opera-
tion (Motor operated)
Battery voltage
Other than above 0
44 G/B Reclining motor BACKWARD
output signal Reclining switch BACKWARD op-
eration (Motor operated)
Battery voltage
Other than above 0
45 G/Y Front lifting motor UP output sig-
nal Front lifting switch UP operation
(Motor operated)
Battery voltage
Other than above 0
48 B Ground — 0
Te r m i n a l
Wire
Color Item Condition Voltage (V)
(Approx.)
Revision: December 20092009 QX56

ADP-128
< ECU DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
Reference ValueINFOID:0000000003775651
TERMINAL LAYOUT
PHYSICAL VALUES
LIIA2449E
Te r m i n a l Wire Col-
or Item Condition Voltage (V)
(Approx.)
1 W/G ADP steering switch TILT UP ADP steering switch in UP position 0
Other than above 5
2 LG Changeover switch RH signal Changeover switch in RH position 0
Other than above 5
3 Y/B Mirror switch UP signal Mirror switch in UP position 0
Other than above 5
4 V/W Mirror switch LEFT signal Mirror switch in LEFT position 0
Other than above 5
5R/B Mirror sensor (
RH vertical) sig-
nal Mirror motor RH is operated UP or
DOWN Changes between 3.4 (close to
peak) 0.6 (close to valley)
6L/Y Mirror sensor (L
H vertical) sig-
nal Mirror motor LH is operated UP or
DOWN Changes between 3.4 (close to
peak) 0.6 (close to valley)
7 Y/BR Tilt sensor input Tilt position TOP 2
Tilt position BOTTOM 4
8 BR/Y Pedal sensor input signal Pedal position front end 0.5
Pedal position rear end 4.5
9 LG/B Seat memory switch 1 signal Memory switch 1 ON 0
Memory switch 1 OFF 5
10 L UART LINE (TX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
12 P Seat memory switch indictor 1
signal Memory switch 1 ON 0
Memory switch 1 OFF Battery voltage
PIIA4813E
Revision: December 20092009 QX56

AUTOMATIC DRIVE POSITIONER CONTROL UNITADP-129
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
13 Y/G Seat memory switch indictor 2
signal Memory switch 2 ON 0
Memory switch 2 OFF Battery voltage
14 GR/R Mirror motor RH UP signal Mirror motor RH is operated
UP 1.5 - Battery voltage
Other than above 0
15 V/R Mirror motor RH LEFT signal Mirror motor RH is operated
LEFT 1.5 - Battery voltage
Other than above 0
16 O Mirror motor LH DOWN signal
Mirror motor LH is operated
DOWN 1.5 - Battery voltage
Other than above 0
Mirror motor LH RIGHT signal Mirror motor LH is operated
RIGHT 1.5 - Battery voltage
Other than above 0
17 G/B ADP steering switch TILT
DOWN ADP steering switch in DOWN posi-
tion
0
Other than above 5
18 BR/W Changeover switch LH signal Changeover switch in LH position 0
Other than above 5
19 SB Mirror switch DOWN signal Mirror switch in DOWN position 0
Other than above 5
20 GR Mirror switch RIGHT signal Mirror switch in RIGHT position 0
Other than above 5
21 L/W Mirror sensor (RH horizontal)
signal Mirror motor RH is operated LEFT or
RIGHT Changes between 3.4 (close to left
edge) 0.6 (close to right edge)
22 G Mirror sensor (LH horizontal)
signal Mirror motor LH is operated LEFT or
RIGHT Changes between 3.4 (close to left
edge) 0.6 (close to right edge)
24 G/O Seat memory set switch signal Set switch 1 ON 0
Set switch 1 OFF 5
25 P/L Seat memory switch 2 signal Memory switch 2 ON 0
Memory switch 2 OFF 5
26 W UART LINE (RX) Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
30 Y Mirror motor RH DOWN signal
Mirror motor RH is operated
DOWN 1.5 - Battery voltage
Other than above 0
Mirror motor RH RIGHT signal Mirror motor RH is operated
RIGHT 1.5 - Battery voltage
Other than above 0
31 R Mirror motor LH UP signal Mirror motor LH is operated
UP 1.5 - Battery voltage
Other than above 0
32 BR Mirror motor LH LEFT signal Mirror motor LH is operated LEFT 1.5 - Battery voltage
Other than above 0
33 W/L Sensor power supply — 5
34 Y/R Battery power supply — Battery voltage
Te r m i n a l
Wire Col-
or Item Condition Voltage (V)
(Approx.)
PIIA4814E
Revision: December 20092009 QX56

ADP-130
< ECU DIAGNOSIS >
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
35 R Tilt motor UP signalADP steering switch in UP position Battery voltage
Other than above 0
37 G Pedal adjust motor FORWARD
signal Pedal adjust motor FORWARD op-
eration (Motor operated)
Battery voltage
Other than above 0
39 L/B Battery power supply — Battery voltage
40 B/W Ground — 0
41 W/G Sensor ground — 0
42 V Tilt motor DOWN signal ADP steering switch in DOWN posi-
tion
Battery voltage
Other than above 0
45 R Pedal adjust motor BACK-
WARD signal Pedal adjust motor BACKWARD op-
eration (Motor operated)
Battery voltage
Other than above 0
48 B Ground — 0
Te r m i n a l
Wire Col-
or Item Condition Voltage (V)
(Approx.)
Revision: December 20092009 QX56

BCM (BODY CONTROL MODULE)ADP-149
< ECU DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Te r m i n a l Wire
color Signal name Signal
input/
output Measuring condition
Reference value or waveform
(Approx.)
Ignition
switch Operation or condition
1BR/W Ignition keyhole illumi-
nation Output OFFDoor is locked (SW OFF) Battery voltage
Door is unlocked (SW ON) 0V
2SB Combination switch
input 5 Input ON
Lighting, turn, wiper OFF
Wiper dial position 4
3G/Y Combination switch
input 4 Input ONLighting, turn, wiper OFF
Wiper dial position 4
4Y Combination switch
input 3 Input ON
Lighting, turn, wiper OFF
Wiper dial position 4
5G/B Combination switch
input 2
Input ONLighting, turn, wiper OFF
Wiper dial position 4
6V Combination switch
input 1
9GR/R Rear window defogger
switch
Input ONRear window defogger switch
ON
0V
Rear window defogger switch
OFF 5V
10 G Hazard lamp flash Input OFF ON (opening or closing) 0V
OFF (other than above) Battery voltage
11 O Ignition switch (ACC
or ON)
InputACC or
ON Ignition switch ACC or ON Battery voltage
12 R/L Front door switch RH Input OFF ON (open) 0V
OFF (closed) Battery voltage
13 GR Rear door switch RH Input OFF ON (open) 0V
OFF (closed) Battery voltage
15 L/W Tire pressure warning
check connector
Input OFF — 5V
18 P Remote keyless entry
receiver and optical
sensor (ground)
Output OFF — 0V
SKIA5291E
SKIA5292E
SKIA5291E
SKIA5292E
Revision: December 20092009 QX56

ADP-150
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
19 V/WRemote keyless entry
receiver (power sup-
ply) Output OFF Ignition switch OFF
20 G/W Remote keyless entry
receiver (signal) Input OFFStand-by (keyfob buttons re-
leased)
When remote keyless entry
receiver receives signal from
keyfob (keyfob buttons
pressed)
21 G NATS antenna amp. Input OFF
→
ON Ignition switch (OFF
→ ON) Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then return to battery voltage.
22 W/V BUS — — Ignition switch ON or power
window timer operates
23 G/O Security indicator
lamp Output OFF
Goes OFF
→ illuminates (Ev-
ery 2.4 seconds) Battery voltage
→ 0V
25 BR NATS antenna amp. Input OFF
→
ON Ignition switch (OFF
→ ON) Just after turning ignition switch
ON: Pointer of tester should
move for approx. 1 second, then return to battery voltage.
26 Y/L Rear wiper auto stop
switch 2 Input ONRise up position (rear wiper
arm on stopper)
0V
A Position (full clockwise stop
position) 0V
Forward sweep (counterclock-
wise direction) Fluctuating
B Position (full counterclock-
wise stop position) Battery voltage
Reverse sweep (clockwise di-
rection) Fluctuating
27 W/R Compressor ON sig-
nal Input ONA/C switch OFF 5V
A/C switch ON 0V
Te r m i n a l
Wire
color Signal name Signal
input/
output Measuring condition
Reference value or waveform
(Approx.)
Ignition
switch Operation or condition
LIIA1893E
LIIA1894E
LIIA1895E
PIIA2344E
Revision: December 20092009 QX56