mirror INFINITI QX56 2010 Factory Owner's Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2010, Model line: QX56, Model: INFINITI QX56 2010Pages: 4210, PDF Size: 81.91 MB
Page 104 of 4210
ADP-90
< COMPONENT DIAGNOSIS >
TILT SENSOR
1. Disconnect automatic drive positioner control unit and tilt motorassembly.
2. Check continuity between automatic drive positioner connector
M33 (A), M34 (B) terminals 7, 33, 41 and tilt motor assembly
connector M85 (C) terminals 2, 3, 4.
3. Check continuity between automatic drive positioner control unit connectors M33 (A), M34 (B) terminals 7, 33, 41 and ground.
Is the inspection result normal?
YES >> Replace tilt motor assembly. Refer to ST-19, "Removal
and Installation".
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR OPERATION
1. Connect automatic drive positioner control unit and tilt motor assembly.
2. Turn ignition switch ON.
3. Check door mirror operation with memory function.
Is the operation normal?
YES >> Replace tilt motor assembly. Refer to ST-19, "Removal and Installation".
NO >> Replace automatic drive posit ioner control unit. Refer to ADP-175, "
Removal and Installation".
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit. Refer to ADP-175, "Removal and Installation".
NO >> Repair or replace the malfunctioning part. 7 - 3
: Continuity should exist.
33 - 2 : Continuity should exist.
41 - 4 : Continuity should exist.
7 - Ground : Continuity should not exist.
33 - Ground : Continuity should not exist.
41 - Ground : Continuity should not exist.
ALJIA0291ZZ
Revision: April 20092010 QX56
Page 106 of 4210
ADP-92
< COMPONENT DIAGNOSIS >
PEDAL ADJUSTING SENSOR
1. Disconect automatic drive positioner control unit and pedaladjusting motor assembly.
2. Check continuity between automat ic drive positioner control unit
harnnes connector and pedal adjusting motor assembly harness
connector.
3. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR OPERATION
1. Connect automatic drive positioner control unit and pedal adjusting motor assembly.
2. Turn ignition switch ON.
3. Check door mirror operation with memory function.
Is the operation normal?
YES >> Replace pedal adjusting motor assembly. Refer to ADP-178, "Removal and Installation".
NO >> Replace automatic drive posit ioner control unit. Refer to ADP-175, "
Removal and Installation".
4. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit. Refer to ADP-175, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Automatic drive posi-
tioner
control unit connector Te r m i n a lPedal adjusting
motor assembly connector Terminal Continuity
M33 (A) 8
E110 (B) 4
Ye s
M34 (C) 33
3
41 5
Automatic drive positioner control unit connector Te r m i n a l
Ground Continuity
M33 (A) 8
No
M34 (C) 33
41
ALJIA0327ZZ
Revision: April 20092010 QX56
Page 107 of 4210
MIRROR SENSORADP-93
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
MIRROR SENSOR
DRIVER SIDE
DRIVER SIDE : DescriptionINFOID:0000000005147544
• The mirror sensor LH is installed to the door mirror actuator LH.
• The resistance of 2 sensors (horizontal and vert ical) is changed when the door mirror LH is operated.
• Automatic drive positioner control uni t calculates the door mirror position according to the change of the volt-
age of 2 sensor input terminals.
DRIVER SIDE : Comp onent Function CheckINFOID:0000000005147545
1. CHECK FUNCTION
1. Select “MIR/SEN LH U-D”, “MIR/SEN LH R- L” in “Data monitor” with CONSULT-III.
2. Check mirror sensor (driver side) signal under the following condition.
Is the indication normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-93, "
DRIVER SIDE : DiagnosisProcedure".
DRIVER SIDE : Diagnosis ProcedureINFOID:0000000005147546
Regarding Wiring Diagram information, refer to ADP-138, "Wiring Diagram".
1. CHECK DOOR MIRROR LH SENSOR SIGNAL
1. Turn ignition switch to ACC.
2. Check voltage between door mirror LH harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK DOOR MIRROR LH SENSOR CIRCUIT 1
Monitor item ConditionValue
MIR/SEN LH U-D Door mirror LHClose to peak
3.4V
Close to valley 0.6V
MIR/SEN LH R-L Close to right edge
3.4V
Close to left edge 0.6V
Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+)
(–)
Door mirror
LH connector Te r m i n a l
D4 7
Ground Door
mirror
LHClose to peak
3.4
Close to valley 0.6
8 Close to right edge 3.4
Close to left edge 0.6
LIIA1482E
Revision: April 20092010 QX56
Page 108 of 4210
ADP-94
< COMPONENT DIAGNOSIS >
MIRROR SENSOR
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror LH.
3. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR LH SENSOR CIRCUIT 2
1. Check continuity between automatic drive positioner control unit harness connector and door mirror LH harness connector.
2. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit and door mirror LH.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator LH. Refer to MIR-19, "Mirror Actuator".
NO >> Replace automatic drive posit ioner control unit. Refer to ADP-175, "
Removal and Installation".
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit. Refer to ADP-175, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M33 6
D4 7
Ye s
22 8
Automatic drive positioner control unit connector Te r m i n a l
Ground Continuity
M33 6
No
22
LIIA1484E
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M34 33
D4 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1483E
Revision: April 20092010 QX56
Page 109 of 4210
MIRROR SENSORADP-95
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
PASSENGER SIDE
PASSENGER SIDE : DescriptionINFOID:0000000005147547
• The mirror sensor RH is installed to the door mirror actuator RH.
• The resistance of 2 sensors (horizontal and vert ical) is changed when the door mirror RH is operated.
• Automatic drive positioner control uni t calculates the door mirror position according to the change of the volt-
age of 2 sensor input terminals.
PASSENGER SIDE : Co mponent Function CheckINFOID:0000000005147548
1. CHECK FUNCTION
1. Select “MIR/SEN RH U-D”, “MIR/SEN RH R-L” in “Data monitor” with CONSULT-III.
2. Check the mirror sensor RH signal under the following conditions.
Is the indication normal?
YES >> Inspection End.
NO >> Perform diagnosis procedure. Refer to ADP-95, "
PASSENGER SIDE : DiagnosisProcedure".
PASSENGER SIDE : Diagnosis ProcedureINFOID:0000000005147549
Regarding Wiring Diagram information, refer to ADP-138, "Wiring Diagram".
1. CHECK DOOR MIRROR RH SENSOR SIGNAL
1. Turn ignition switch to ACC.
2. Check voltage between door mirror RH harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2. CHECK DOOR MIRROR RH SENSOR HARNESS CONTINUITY
Monitor item ConditionValue
MIR/SEN RH U-D Door mirror RHClose to peak
3.4V
Close to valley 0.6V
MIR/SEN RH R-L Close to right edge
3.4V
Close to left edge 0.6V
Te r m i n a l s
ConditionVoltage (V)
(Approx.)
(+)
(–)
Door mirror
RH con-
nector Te r m i n a l
D107 7
Ground Door mirror
RH Close to peak
3.4
Close to valley 0.6
8 Close to right edge 3.4
Close to left edge 0.6
LIIA1485E
Revision: April 20092010 QX56
Page 110 of 4210
ADP-96
< COMPONENT DIAGNOSIS >
MIRROR SENSOR
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir-
ror RH.
3. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK DOOR MIRROR RH SENSOR POWER SUPPLY CIRCUIT
1. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
2. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4. CHECK PEDAL ADJUSTING OPERATION
1. Connect driver seat control unit and door mirror RH.
2. Turn ignition switch ON.
3. Check pedal adjusting operation with memory function.
Is the operation normal?
YES >> Replace door mirror actuator RH. Refer to MIR-19, "Mirror Actuator".
NO >> Replace automatic drive posit ioner control unit. Refer to ADP-175, "
Removal and Installation".
5. CHECK INTERMITTENT INCIDENT
Refer to GI-38, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit. Refer to ADP-175, "Removal and Installation".
NO >> Repair or replace the malfunctioning part.
Automatic drive posi-
tioner control unit connector Terminal
Door mirror RH
connector Terminal Continuity
M33 5
D107 7
Ye s
21 8
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M33 5
No
21
LIIA1473E
Automatic drive posi-
tioner control unit connector Te r m i n a l
Door mirror RH
connector Terminal Continuity
M34 33
D107 5
Ye s
41 6
Automatic drive positioner control unit connector Te r m i n a l
GroundContinuity
M34 33
No
41
LIIA1486E
Revision: April 20092010 QX56
Page 123 of 4210
DOOR MIRROR MOTORADP-109
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DOOR MIRROR MOTOR
DescriptionINFOID:0000000005147568
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
Component Function CheckINFOID:0000000005147569
1. CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to ADP-28, "
CONSULT-III Function".
Is the inspection result normal?
YES >> Door mirror motor function is OK.
NO >> Refer to ADP-109, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005147570
Regarding Wiring Diagram information, refer to ADP-138, "Wiring Diagram".
1. CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES >> Refer to A D P - 111 , "Component Inspection".
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mir- ror.
3. Check continuity between automat ic drive positioner control unit
connector and door mirror connector.
Door mirror LH
Te r m i n a l s
Door mirror re-
mote control
switch condition Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector Te r m i n a l
D4 (LH)
D107 (RH) 1
Ground UP
Battery voltage
Other than above 0
2 LEFT
Battery voltage
Other than above 0
3 DOWN / RIGHT Battery voltage
Other than above 0
ALJIA0196ZZ
Automatic drive
positioner control unit connector Te r m i n a l
Door mirror LH
connector Terminal Continuity
M33 16
D4 3
Ye s
31 1
32 2
LIIA1880E
Revision: April 20092010 QX56
Page 124 of 4210
ADP-110
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
Door mirror RH
4. Check continuity between automatic drive positioner control unitconnector and ground.
Door mirror LH
Door mirror RH
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit.
2. Turn ignition switch ON.
3. Check voltage between automatic drive positioner control unit connector and ground.
Door mirror LH
Automatic drive posi-
tioner control unit con-
nector Te r m i n a l
Door mirror
RH connector Terminal Continuity
M33 14
D107 1
Ye s
15 2
30 3
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 16
No
31
32
Automatic drive position- er control unit connector Te r m i n a l
GroundContinuity
M33 14
No
15
30
LIIA1888E
Te r m i n a l s
Mirror switch condition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner control
unit connector Te r m i n a l
M33 16
Ground DOWN / RIGHT Battery voltage
Other than above 0
31 UP
Battery voltage
Other than above 0
32 LEFT
Battery voltage
Other than above 0
ALJIA0197ZZ
Revision: April 20092010 QX56
Page 125 of 4210
DOOR MIRROR MOTORADP-111
< COMPONENT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Door mirror RH
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace automatic drive positioner control unit. Refer to ADP-175, "
Removal and Installation".
4. CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to ADP-111, "
Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-38, "Intermittent Incident".
NO >> Replace door mirror actuator. Refer to MIR-19, "
Mirror Actuator".
Component InspectionINFOID:0000000005147571
1. CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to MIR-17, "
Door Mirror Assembly".
Is the inspection result normal?
YES >> GO TO 2
NO >> Replace door mirror actuator. Refer to MIR-19, "
Mirror Actuator".
2. CHECK DOOR MIRROR MOTOR-II
1. Turn ignition switch OFF.
2. Disconnect door mirror.
3. Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace door mirror actuator. Refer to MIR-19, "
Mirror Actuator".
Te r m i n a l s
Mirror switch con-dition Voltage (V)
(Approx.)
(+)
(-)
Automatic drive
positioner con-
trol unit connec-
tor Te r m i n a l
M33 14
GroundUP
Battery voltage
Other than above 0
15 LEFT
Battery voltage
Other than above 0
30 DOWN / RIGHT Battery voltage
Other than above 0
ALJIA0198ZZ
Door mirror connector Terminal
Operational direction
(+) (–)
D4 (LH)
D107 (RH) 32 R
IG HT
23 L EFT
13 U P
31 D OW N
ALJIA0199ZZ
Revision: April 20092010 QX56
Page 128 of 4210
ADP-114
< ECU DIAGNOSIS >
DRIVER SEAT CONTROL UNIT
ECU DIAGNOSIS
DRIVER SEAT CONTROL UNIT
Reference ValueINFOID:0000000005147576
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor ItemCondition Value/Status
SET SW Set switch Push
ON
Release OFF
MEMORY SW1 Memory switch 1 Push
ON
Release OFF
MEMORY SW2 Memory switch 2 Push
ON
Release OFF
SLIDE SW–FR Sliding switch (front) Operate
ON
Release OFF
SLIDE SW–RR Sliding switch (rear) Operate
ON
Release OFF
RECLN SW–FR Reclining switch (front) Operate
ON
Release OFF
RECLN SW–RR Reclining switch (rear) Operate
ON
Release OFF
LIFT FR SW–UP Lifting switch front (up) Operate
ON
Release OFF
LIFT FR SW–DN Lifting switch front (down) Operate
ON
Release OFF
LIFT RR SW–UP Lifting switch rear (up) Operate
ON
Release OFF
LIFT RR SW–DN Lifting switch rear (down) Operate
ON
Release OFF
MIR CON SW–UP Mirror switch Up
ON
Other than above OFF
MIR CON SW–DN Mirror switch Down
ON
Other than above OFF
MIR CON SW–RH Mirror switch Right
ON
Other than above OFF
MIR CON SW–LH Mirror switch Left
ON
Other than above OFF
MIR CHNG SW–R Chan geover switchRight
ON
Other than above OFF
MIR CHNG SW–L Chan geover switchLeft
ON
Other than above OFF
PEDAL SW-FR Pedal adjusting switch Forward
ON
Other than above OFF
PEDAL SW-RR Pedal adjusting switch Backward
ON
Other than above OFF
Revision: April 20092010 QX56