atf INFINITI QX56 2011 Factory Workshop Manual

TM-226
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
4WD MODELS
DisassemblyINFOID:0000000006226917
CAUTION:
Never disassemble parts behind
drum support. Refer to TM-16, "
TRANSMISSION : Cross-Sectional
View".
1. Drain ATF through drain plug.
12 B 135 (5.315)
13 A 48.4 (1.906)
Location Shape of snap ring Outer diameter mm (in)
Location Shape of snap ring Outer diameter mm (in)
1 A 159.9 (6.295)
2 B 159 (6.260)
3 B 216 (8.504)
4 B 180.4 (7.102)
5 C 171.5 (6.752)
6 B 169 (6.654)
7 B 180.5 (7.106)
8 B 181.0 (7.126)
9 D 64.6 (2.543)
10 B 136 (5.354) 11 E 70.5 (2.776)
12 B 135 (5.315)
13 A 48.4 (1.906)
JSDIA1734ZZ
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-243
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
68. Remove rear oil seal from rear extension (B) or adapter case (C) using a flat-bladed screwdriver (A).
CAUTION:
Be careful not to scratch adapter case.
AssemblyINFOID:0000000006226918
1. As shown in the figure, use a drift [22 mm (0.87 in) dia. commer-cial service tool] to drive manual shaft oil seals into the transmis-
sion case until it is flush.
CAUTION:
 Never reuse manual shaft oil seals.
 Apply ATF to manual shaft oil seals.
2. Install detent spring to transmission case. Tighten detent spring bolt to the specified torque.
B: 2WD
C: 4WD
JSDIA0157ZZ
SCIA5259E
: Bolt
JPDIA1134ZZ
Revision: 2010 May2011 QX56

TM-248
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
21. As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD) (A) or adapter case (4WD) (B) until it is
flush.
CAUTION:
 Never reuse rear oil seal.
 Apply ATF to rear oil seal.
22. Install return spring (1) to parking pawl (2).
23. Install parking pawl (with return spring) and pawl shaft to rear extension (2WD) or adapter case (4WD).
24. Install parking actuator support to rear extension (2WD) or adapter case (4WD).
1 : Drift [SST: 33400001 (J-26082)]
2 : Drift [Commercial service tool Ø64 mm (2.52 in)]
JSDIA1914ZZ
SCIA6180J
SCIA3424E
SCIA3423E
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-263
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
55. Install under drive sun gear (with needle bearing) (1) to oil pump assembly (2).
56. Install oil pump assembly (with under drive sun gear) to trans- mission case.
CAUTION:
Apply ATF to oil pump bearing.
57. Apply recommended sealant to oil pump assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
58. Tighten oil pump bolts ( ) to the specified torque. CAUTION:
Apply ATF to oil pump bushing.
59. Install O-ring to input clutch assembly.
JSDIA1712ZZ
SCIA2811E
: Genuine RTV silicone sealant or equivalent. Refer to
GI-22, "
Recommended Chemical Products and Seal-
ants".
JSDIA1720ZZ
JPDIA1108ZZ
SCIA5011E
Revision: 2010 May2011 QX56

TM-264
< UNIT DISASSEMBLY AND ASSEMBLY >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
60. Install converter housing to transmission case, and tighten con-
verter housing bolts ( ) to the specified torque.
61. Connect TCM connector (A).
62. Install joint connector (1) to the control valve & TCM. CAUTION:
Apply ATF to O-ring of joint connector.
63. Install the control valve & TCM (1) to transmission case.
CAUTION:
JPDIA1107ZZ
JSDIA1813ZZ
JSDIA1719ZZ
JSDIA1823ZZ
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-267
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
74. Pour ATF into torque converter. Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.
 When reusing old torque co nverter, add the same amount
of ATF as was drained.
75. Install torque converter while aligning notches of torque con- verter with notches of oil pump.
CAUTION:
Install torque converte r while rotating it.
76. Measure dimension “A” to make sure that torque converter is in proper position.
InspectionINFOID:0000000006226919
INSPECTION AFTER REMOVAL
Oil Pan
Check foreign materials in oil pan to help determine causes of mal-
function. If the ATF is very dark, smells burned, or contains foreign
particles, the frictional material (clutches, band) may need replace-
ment. A tacky film that will not wipe clean indicates varnish build up.
Varnish can cause valves, servo, and clutches to stick and can
inhibit pump pressure.
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to TM-97, "
Cleaning".
Torque Converter
SAT428DA
SCIA5010E
B: Scale
C : Straightedge
Dimension “A” : Refer to TM-297, "Torque Converter".
JPDIA0042ZZ
SCIA5199E
Revision: 2010 May2011 QX56

OIL PUMP, 2346 BRAKE, FRONT BRAKE PISTONTM-275
< UNIT DISASSEMBLY AND ASSEMBLY > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
3. Using the drift, install oil pump housing oil seal to the oil pump housing until it is flush.
CAUTION:
 Never reuse oil seal.
 Apply ATF to oil seal.
4. Install oil pump housing to oil pump cover and tighten bolts ( ) to the specified torque in numerical order shown in the figure
after temporarily tightening them.
5. Install D-ring (large) (1) and D-ring (small) (2) to 2346 brake pis- ton.
6. Install 2346 brake piston (1) to oil pump assembly.
7. Install D-ring (inner) (1) and D-ring (outer) (2) to front brake pis- ton.
SCIA5313E
JPDIA1101ZZ
JPDIA1100ZZ
JSDIA1722ZZ
JPDIA1098ZZ
Revision: 2010 May2011 QX56

TM-296
< SERVICE DATA AND SPECIFICATIONS (SDS) [7AT: RE7R01B]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000006226944
*1: Refer to
MA-10, "Fluids and Lubricants".
*2: The fluid capacity is the reference value.
Vehicle Speed at Which Gear Shifting OccursINFOID:0000000006226945
NORMAL MODE
Unit: km/h (MPH)
 At half throttle, the accelerator opening is 4/8 of the full opening.
TOW MODE
Applied model 2WD 4WD
Transmission model code number 1XR1E 1XR1D
Stall torque ratio 1.93 : 1
Transmission gear ratio 1st 4.887
2nd 3.170
3rd 2.027
4th 1.412
5th 1.000
6th 0.864
7th 0.775
Reverse 4.041
Recommended fluid Genuine NISSAN Matic S ATF
*1
Fluid capacity10.0 liter (10-5/8 US qt, 8-3/4 Imp qt)*2
CAUTION:
 Use only Genuine NISSAN Matic S ATF. Never mix with other ATF.
 Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration driveability and A/T durability, and may damage
the A/T, which is not covered by the INFINITI new vehicle limited warranty.
Gear position Throttle position
Full throttle Half throttle
D
1 → D256 – 60 (35 – 37) 42 – 46 (26 – 29)
D
2 → D389 – 97 (55 – 60) 73 – 81 (45 – 50)
D
3 → D4141 – 151 (88 – 94) 112 – 122 (70 – 76)
D
4 → D5205 – 215 (127 – 134) 134 – 144 (83 – 89)
D
5 → D6250 – 260 (155 – 162) 173 – 183 (108 – 114)
D
6 → D7250 – 260 (155 – 162) 206 – 216 (128 – 134)
D
7 → D6240 – 250 (149 – 155) 161 – 171 (100 – 106)
D
6 → D5240 – 250 (149 – 155) 130 – 140 (81 – 87)
D
5 → D4180 – 190 (112 – 118) 84 – 94 (52 – 58)
D
4 → D3126 – 136 (78 – 85) 58 – 68 (36 – 42)
D
3 → D266 – 74 (41 – 46) 30 – 38 (19 – 24)
D
2 → D123 – 27 (14 – 17) 10 – 14 (6 – 9)
Revision: 2010 May2011 QX56

WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-15
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
K L
M B A
O P
FR FOG IND
[Off] This item is displayed, but cannot be monitored.
RR FOG IND
[Off] This item is displayed, but cannot be monitored.
LIGHT IND
[On/Off] Status of light indicator lamp detected from position light request signal is received
from BCM via CAN communication.
OIL W/L
[On/Off] Status of oil pressure warning lamp detected from oil pressure switch signal is re-
ceived from BCM via CAN communication.
MIL
[On/Off] Status of malfunction indicator lamp detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.
GLOW IND
[Off] This item is displayed, but cannot be monitored.
CRUISE IND
[On/Off]  Status of CRUISE indicator detected from ASCD status signal is received from
ECM via CAN communicat ion. (ASCD models)
 Status of CRUISE indicator de tected from meter display signal is received from
ADAS control unit via CAN communication. (ICC models)
SET IND
[On/Off] Status of SET indicator detected from meter display signal is received from ADAS
control unit via CAN communication.
CRUISE W/L
[On/Off] Status of CRUISE warning lamp
judged from ICC warning lamp signal received
from ADAS control unit with CAN communication line.
BA W/L
[On/Off] Status of IBA OFF indicator lamp judged from IBA OFF indicator lamp signal re-
ceived from ADAS control unit with CAN communication line.
ATC/T-AMT W/L
[On/Off] Status of A/T CHECK warning lamp judged
from A/T CHECK indicator lamp signal
received from TCM with CAN communication line.
ATF TEMP W/L
[Off] This item is displayed, but cannot be monitored.
4WD W/L
[On/Off] Status of 4WD warning lamp judged from 4WD warning lamp signal received from
4WD control unit with
CAN communication line.
FUEL W/L
[On/Off] Low-fuel warning lamp status detected by the identified fuel level.
WASHER W/L
[On/Off] Status of low washer fluid warning judged from washer level switch input to com-
bination meter.
AIR PRES W/L
[On/Off] Status of low tire pressure warning lamp judged from low tire pressure warning
lamp signal received from BCM with CAN communication line.
KEY G/Y W/L
[On/Off] Status of KEY warning lamp
(Green/Yellow) detected from KEY warning lamp sig-
nal is received from BCM via CAN communication.
KEY KNOB W/L
[Off] This item is displayed, but cannot be monitored.
AFS OFF IND
[On/Off] Status of AFS OFF indicator lamp judged from AFS OFF indicator lamp signal re-
ceived from AFS control unit with CAN communication line.
DDS
* W/L
[Off] This item is displayed, but cannot be monitored.
LANE W/L
[On/Off] Status of lane departure warning lamp judged from lane departure warning lamp
signal received from ADAS control unit with CAN communication line.
LDP IND
[On/Off] Status of LDP ON indicator lamp judged from LDP ON indicator lamp signal re-
ceived from ADAS control unit with CAN communication line.
AT P W / L
[On/Off] Status of ATP warning lamp judged from ATP warning lamp signal received from
4WD control unit with
CAN communication line.
DCA IND
[Off] This item is displayed, but cannot be monitored.
CHECK SUS IND
[On/Off] Status of CK SUSP indicator lamp judged from CK SUSP indicator lamp signal re-
ceived from E-SUS control unit with CAN communication line.
Display item [Unit]
MAIN
SIGNALS Description
Revision: 2010 May2011 QX56

WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-17
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
K L
M B A
O P
*: DDS (hill descent control) NOTE:
Some items are not available according to vehicle specification.
SPECIAL FUNCTION
Special menu
W/L ON HISTORY
 Stores histories when warning/indicator lamp is turned on.
 “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
 The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
 W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
 Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item
FUEL LOW SIG
[On/Off] Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.
TOW MODE IND
[On/Off] Status of TOW mode indicator lamp judged from TOW mode indicator lamp signal
received from TCM with CAN communication line.
BUZZER
[On/Off] XBuzzer status (in the combination meter) is detected from the buzzer output signal
received from each unit via CAN communication and the warning output condition
of the combination meter.
Display item [Unit]
MAIN
SIGNALS Description
Display item Description
W/L ON HISTORY Lighting history of warning lamp and indicator lamp can be checked.
Display item Description
ABS W/L Lighting history of ABS warning lamp.
VDC/TCS IND Lighting history of VDC OFF indicator lamp.
SLIP IND Lighting history of VDC warning lamp.
BRAKE W/L Lighting history of brake warning lamp.
DOOR W/L Lighting history of door open warning.
TRUNK/GLAS-H This item is displayed, but cannot be monitored.
OIL W/L Lighting history of oil pressure warning lamp.
C-ENG W/L Lighting history of malfunction indicator lamp.
C-ENG2 W/L This item is displayed, but cannot be monitored.
CRUISE IND Lighting history of CRUISE indicator lamp.
SET IND Lighting history of SET indicator lamp.
CRUISE W/L Lighting histor y of CRUISE warning lamp.
BA W/L Lighting history of IBA OFF indicator lamp.
O/D OFF IND This item is displayed, but cannot be monitored.
ATC/T-AMT W/L Lighting history of A/T CHECK warning lamp.
ATF TEMP W/L This item is displayed, but cannot be monitored.
CVT IND This item is displayed, but cannot be monitored.
SPORT IND This item is displayed, but cannot be monitored.
Revision: 2010 May2011 QX56