4WD INFINITI QX56 2011 Factory Service Manual

FRONT DISC BRAKEBR-17
< PERIODIC MAINTENANCE >
C
DE
G H
I
J
K L
M A
B
BR
N
O P
 Check in advance that the thickness of the disc rotor is wear thickness + 0.3 mm (0.012 in) or
more.
 If the thickness is less than wear thickness + 0. 3 mm (0.012 in), replace the disc rotor. Refer to
FA X - 8 , "
Removal and Installation" (2WD), FAX-18, "Removal and Installation".
Thickness
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thickness is below the wear limit. Refer to FAX-8,
"Removal and Installation" (2WD), FAX-18, "Removal and Installa-
tion" (4WD).
ADJUSTMENT
CAUTION:
 Burnish contact surfaces between pads according to the following procedure after refinishing or
replacing brake pads, or if a soft pedal occurs at very low mileage.
 Be careful of vehicle speed because the brake does not operate firmly/securely until pads and disc
rotor are securely fitted.
 Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicl e within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake for a few minutes to cool the brake.
4. Repeat steps 1 to 3 until pad and disc rotor are securely fitted. Wear thickness : Refer to
BR-47, "
Front Disc Brake".
Wear thickness : Refer to BR-47, "
Front Disc Brake".
JPFIA0719ZZ
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-11
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
4WD
1. ECM Refer to EC-16, "
Component Parts
Location". 2. Control valve & TCM
Refer to TM-10, "
A/T CONTROL
SYSTEM : Compon ent Parts Loca-
tion". 3. Front wheel sensor
4. ABS actuator and electric unit (con- trol unit) 5. Stop lamp switch 6. Steering angle sensor
7. VDC OFF switch 8. Yaw rate/side/decel G sensor 9. Rear wheel sensor
A. Front wheel hub and bearing assem- bly B. Inside engine room C. Brake pedal
D. ABS warning lamp, brake warning lamp, VDC warning lamp, VDC OFF
indicator lamp E. Back of spiral cable assembly F. Center console assembly
G. Under center console assembly H. Rear wheel hub and bearing assem- bly
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-13
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Component DescriptionINFOID:0000000006222560
*1: Models with Advanced Driver Assistance System
*2: Models with 4WD system
D. ABS warning lamp, brake warning lamp, VDC warning lamp, VDC OFF
indicator lamp E. Back of spiral cable assembly F. Center console assembly
G. Under center console assembly H. Rear wheel hub and bearing assem- bly
Component Reference/Function
ABS actuator and electric unit
(control unit) Motor/accumulator assembly
BRC-14, "
ABS Actuator and Electric Unit (Control Unit)"
Motor relay
Actuator relay (main relay)
ABS IN valve
ABS OUT valve
Cut valve 1
Cut valve 2
Suction valve 1
Suction valve 2
Control pressure sensor
*1
Accumulator pressure sensor
Master cylinder pressure sensor
Wheel sensor BRC-14, "
Wheel Sensor and Sensor Rotor"
Stop lamp switchBRC-15, "Stop Lamp Switch"
Steering angle sensorBRC-15, "Steering Angle Sensor"
Yaw rate/side/decel G sensorBRC-15, "Yaw Rate/Side/Decel G sensor"
Brake fluid level switch BRC-15, "Brake Fluid Level Switch"
Parking brake switchBRC-15, "Parking Brake Switch"
VDC OFF switchBRC-15, "VDC OFF Switch"
ECMMainly transmits the
following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and
electric unit (control unit) via CAN communication.
 Target throttle position signal
TCM Mainly transmits the
following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Shift position signal
 Current gear position signal
Transfer control unit
*2Mainly transmits the following signals to ABS actuator and elec-
tric unit (control unit) via CAN communication.
 Current 4WD mode signal
ABS warning lamp
BRC-16, "
System Description"Brake warning lamp
VDC warning lamp
VDC OFF indicator lamp
Revision: 2010 May2011 QX56

COMPONENT PARTSBRC-15
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
 Downsize and weight reduction is aimed. IC for detection portion and magnet for sensor rotor are adopted.
 Power supply is supplied to detection portion so that magnetic field
line is read. Magnetic field that is detected is converted to current
signal.
 When sensor rotor rotates, magnetic field changes. Magnetic field
change is converted to current signals (rectangular wave) and is
transmitted to ABS actuator and electric unit (control unit). Change
of magnetic field is pr oportional to wheel speed.
Stop Lamp SwitchINFOID:0000000006222563
Detects the operation status of brake pedal and transmits converted electric signal to ABS actuator and elec-
tric unit (control unit).
Steering Angle SensorINFOID:0000000006222564
Detects the following information and transmits steering angle signal to ABS actuator and electric unit (control
unit) via CAN communication.
 Steering wheel rotation amount
 Steering wheel rotation angular velocity
 Steering wheel rotation direction
Yaw Rate/Side/Decel G sensorINFOID:0000000006222565
Calculates the following information that affects the v ehicle and transmits a signal to ABS actuator and electric
unit (control unit) via communication lines.
 Vehicle rotation angular velocity (yaw rate signal)
 Vehicle lateral acceleration (side G signal) / longitudinal acceleration (decel G signal)
Brake Fluid Level SwitchINFOID:0000000006222566
Detects the brake fluid level in reservoir tank and trans mits converted electric signal from ABS actuator and
electric unit (control unit), when brake fluid level is the specified level or less.
Parking Brake SwitchINFOID:0000000006222567
Detects the operation status of parking brake switch and transmits converted electric signal from combination
meter to ABS actuator and electric unit (control unit).
VDC OFF SwitchINFOID:0000000006222568
 VDC OFF switch is integrated in SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
 The operation of the VDC OFF switch enables the arbi trary switching of the VDC function between stop sta-
tus and standby status. The status of the function is indicated by the VDC OFF indicator lamp. (ON: Non-
operational status, OFF: Standby status)
- VDC function NOTE:
Brake limited slip differentia l (BLSD) control operates.
- TCS function
 VDC OFF indicator lamp turns OFF (standby status) when the engine is started again after it is stopped once while VDC OFF indicator lamp is ON (non-operational status).
JPFIC0131GB
Revision: 2010 May2011 QX56

BRC-16
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006222569
 The system switches fluid pressure of each brake caliper to increase, to hold or to decrease according to
signals from control unit in ABS actuator and electric unit (control unit). This control system is applied to
VDC function, TCS function, ABS func tion, EBD function, hill start assist function and brake limited slip dif-
ferential (BLSD) function
 Fail-safe function is available for each function and is activated by each function when system malfunction occurs.
 The adoption of the 4WD switch assembly (4WD sh ift switch and VDC OFF switch) enables to change the
control characteristics of the VDC function, the TCS function and the brake limited slip differential (BLSD)
function into an optimal characteristics, based on a st ate of the 4WD shift switch. (Models with 4WD system)
SYSTEM DIAGRAM
NOTE:
Transfer control unit is appli ed to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
JPFIC0182GB
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the follo
wing signals to ABS actuator and elec tric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the follo
wing signals to ABS actuator and elec tric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following si gnals from ABS actuator and electr ic unit (control unit) via CAN
communication.
 Target throttle position signal
Revision: 2010 May2011 QX56

SYSTEMBRC-17
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P*1: Communication line between yaw rate/side/decal G s ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
VALVE OPERATION
Each valve is operated and fluid pressure of brake caliper is controlled.
When Ordinary Brake is Applied
NOTE:
Control pressure sensor is applied to model s with Advanced Driver Assistance System.
TCMMainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
 Current gear position signal
Transfer control unit
*2Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Steering angle sensor Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
 Steering angle sensor signal
Combination meter Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 ABS warning lamp signal
 Brake warning lamp signal
 VDC warning lamp signal
 VDC OFF indicator lamp
Component Signal description
Name Not activated When depressing brake pedal
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close)
JPFIC0150GB
Revision: 2010 May2011 QX56

SYSTEMBRC-25
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC Warning Lamp
 Turns ON when either VDC function,
TCS function, ABS function or EBD function, hill start assist function or
brake limited slip differential (BLSD) function is malfunctioning.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
CONDITION FOR TURN ON THE INDICATOR LAMP
VDC OFF Indicator Lamp
 Turns ON when VDC function and TCS function are s witched to non-operational status (OFF) by VDC OFF
switch.
 Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
*: Models with 4WD system
Fail-safeINFOID:0000000006228184
VDC FUNCTION, TCS FUNCTION, hill start assi st FUNCTION AND BRAKE LIMITED SLIP DIFFER-
ENTIAL (BLSD) FUNCTION
VDC warning lamp in combination meter turn ON w hen a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC function, TCS function, hill start assist function
and brake limited slip differential (BLSD) function. T he Vehicle status becomes the same as models without
VDC function, TCS function, hill star t assist function and brake limited slip differential (BLSD) function. How-
ever, ABS function and EBD f unction are operated normally.
When brake fluid is less than the specified level (brake fluid level
switch ON) ON
ABS function is malfunctioning OFF
EBD function is malfunctioning ON
Accumulator is low pressure ON
Motor system is malfunctioning ON
Ignition power supply system is malfunctioning ON Condition (status) Brake warning lamp
Condition (status) VDC warning lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
VDC function is malfunctioning ON
TCS function is malfunctioning ON
ABS function is malfunctioning ON
EBD function is malfunctioning ON
hill start assist function is malfunctioning ON
Brake limited slip differential (BLSD) function is malfunctioning ON
VDC function is operating Blinking
TCS function is operating Blinking
Condition (status) VDC OFF indicator lamp
Ignition switch OFF OFF
For approx. 1 seconds after the ignition switch is turned ON ON
Approx. 1 seconds after ignition switch is turned ON (when the
system is in normal operation) OFF
When VDC OFF switch is ON (VDC function and TCS function are
OFF) ON
4WD mode: 4L
*ON
Revision: 2010 May2011 QX56

BRC-28
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
*1: Models with 4WD System
*2: Models with Advanced Driver Assistance System
Protection FunctionINFOID:0000000006228185
The VDC warning lamp, ABS warning lamp and brake warning lamp turns ON and DTC “C118E” may be
detected in self-diagnosis result of “ABS” when the br
ake pedal is excessively operated, such as air bleeding.
This is not a system malfunction because this occurs due to the temporary decrease in accumulator fluid pres-
sure. The system returns to normal condition when the accu mulator fluid pressure reaches the specified pres-
sure with the ignition switch ON and the VDC warning lamp, ABS warning lamp, and brake warning lamp turn
OFF. After these steps, erase self-diagnos is results for “ABS” with CONSULT-III.
NOTE:
D T C “ C 1111 ” i s d e t e c t e d i n s e l f - d i agnosis results of “ABS” when the a ccumulator system has a malfunction.
VDC FUNCTION
VDC FUNCTION : System DescriptionINFOID:0000000006222572
 Side slip or tail slip may occur while driving on a slippery road or intending an urgent evasive driving. VDC
function detects side slip status using each sensor when side slip or tail slip is about to occur and improves
vehicle stability by brake control and engine output control during driving.
 In addition to ABS function, EBD function and TCS functi on, target side slip amount is calculated according
to steering operation amount from steering angle sensor and brake operation amount from pressure sensor.
By comparing this information with vehicle side slip amount that is calculated from information from yaw rate/
C118EWhen performing excessive brake pedal operation with the vehicle stopped. [When
accumulator fluid pressure reaches 11.43 MPa (114 bar, 116.6 kg/cm2, 1657 psi) af-
ter reaching 17.3 MPa (173 bar, 176.5 kg/cm2, 2509 psi.] The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential
(BLSD) function
U1000 When CAN communication signal is not continuously received for 2 seconds or
more. The following functions are sus-
pended.
 VDC function
 TCS function
 ABS function
 hill start assist function
 Brake limited slip differential
(BLSD) function
DTC Malfunction detected condition Fail-safe condition
DTC
 VDC warning lamp
 ABS warning lamp
 Brake warning lamp
Condition Description protection function
C118E ON When temporary decrease in accumulator fluid pres-
sure.
NOTE:
System is not malfunction. The following functions are suspended
temporarily
 VDC function
 TCS function
 ABS function
 EBD function
 hill start assist function
 Brake limited slip differential (BLSD)
function
Revision: 2010 May2011 QX56

SYSTEMBRC-29
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
side/decel G- sensor and wheel sensor, vehicle drivi ng conditions (conditions of understeer or oversteer) are
judged and vehicle stability is improved by brake forc e control on all 4 wheels and engine output control.
 Control unit portion automatically improves driving st ability by performing brake force control as well as
engine output control, by transmitting drive signal to actuator portion according to difference between target
side slip amount and vehicle side slip amount
 VDC function can be switched to non-operational status (OFF) by operating VDC OFF switch. In this case,
VDC OFF indicator lamp turns ON.
 VDC function is not operate when 4WD mode is “4L”. (Models with 4WD system)
 VDC warning lamp blinking while VDC function is in oper ation and indicates to the driver that the function is
in operation.
 Slight vibrations are felt on the brake pedal and t he operation noises occur, when VDC function operates.
This is not a malfunction because it is caus ed by VDC function that is normally operated.
 CONSULT-III can be used to diagnose the system diagnosis.
 Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function, TCS function, hill start as sist function and brake limited slip di fferential (BLSD) function. The vehi-
cle status becomes the same as m odels without VDC function, TCS functi on, hill start assist function and
brake limited slip differential (BLSD) function. Ho wever, ABS function and EBD function are operated nor-
mally. Refer to BRC-25, "
Fail-safe".
NOTE:
VDC has the characteristic as de scribed here, but it is not the device that helps reckless driving.
SYSTEM DIAGRAM
NOTE:
Transfer control unit is applied to models with 4WD system.
INPUT SIGNAL AND OUTPUT SIGNAL
JPFIC0133GB
JPFIC0183GB
Revision: 2010 May2011 QX56

BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s
ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
 During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer side of turn. Moment directing towards the outer side of turn is generated. Oversteer is prevented.
 Changing driving lane on a slippery road, when oversteer tendency is judged large, engine output is con- trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
VDC Function That Prevents Understeer Tendency
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
 Yaw rate signal
 Side G sensor signal
 Decel G sensor signal
ECM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Accelerator pedal position signal
 Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 Target throttle position signal
TCM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Shift position signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Current 4WD mode signal
Steering angle sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
 Steering angle sensor signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
 VDC warning lamp signal
 VDC OFF indicator lamp
JPFIC0135GB
JPFIC0136GB
Revision: 2010 May2011 QX56