key fob INFINITI QX60 HYBRID 2016 Quick Reference Guide

8
Infiniti Intelligent Key System
The Infiniti Intelligent Key system allows you to lock or unlock your ve\
hicle, open your liftgate
and remotely start the hybrid system. It is important to make sure the I\
ntelligent Key is with
you (that is, in your pocket or purse).
LOCKING AND UNLOCKING THE VEHICLE
The lock and unlock operating range of the Intelligent Key is within 31.\
5 in (80 cm) from
each request switch.
To lock the vehicle, push either door handle request
switch
1 once or press the button 2 on the
key fob.
To unlock the vehicle, perform one of the
following procedures:
• Push either door handle request switch 1 once; the corresponding door will unlock.
Push the door handle request switch
1 again within 1 minute; all other doors will
unlock, or
• Press the button 4 on the key fob to unlock the driver’s side door. Press the button
4 again; all other doors will unlock.
REMOTE HYBRID SYSTEM START* (if so equipped)
The remote hybrid system start must be enabled in the vehicle
settings within the vehicle information display.
The remote hybrid system start operating range is approximately
200 ft (60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.
For the remote hybrid system start to function, the vehicle must be
in the P (PARK) position with the ignition off and all the doors
closed and locked.
To start your vehicle remotely:
1. Press the button 2.
2. Within 5 seconds, press and hold the remote hybrid system start button 3 for at
least 2 seconds.
The hybrid system will start, and the parking lights will turn on.
Automatic climate control will begin heating or cooling the vehicle depe\
nding on the
outside ambient temperature.
The hybrid system will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10-minute peri\
od.
• After two remote starts, the ignition switch must be cycled before the r\
emote start can be
used again.
To start driving, depress the brake pedal and press the ignition switch \
START/STOP button.
first drive features
3
2
4
5
6
1
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.

15
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
1 memory.
Follow this procedure to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
• Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the adjusting switches fo\
r each feature.
• Push the SET switch, and within 5 seconds, push the memory switch (
1 or 2).
• The indicator light on the memory switch you select will illuminate for \
approximately 5
seconds, and a chime will sound (if so equipped) when the memory is st\
ored correctly.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to
your preferences.
These memorized positions can also be linked to your Infiniti Intelligen\
t Key. To link a
memorized position to your Infiniti Intelligent Key, press the unlock bu\
tton on the key fob
after completing the previous step.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch
1 right or left.
Adjust each mirror to the desired position using the
control switch
2.
To fold the outside rearview mirrors, push the
control switch
3 to the position. To unfold the
outside rearview mirrors, push the control switch
3 to the position.
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirror surfaces dow\
nward to provide
better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Choose the right or left outside mirror by operating the control switch \
1.
3. Move the shift lever to the R (REVERSE) position.
4. The outside mirror surfaces will move downward. (The control switch 1 must be out of
the center [neutral] position.)
The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The control switch 1 is set to the center (neutral) position.
• The ignition switch is placed in the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
1
2
1
3