ESP INFINITI QX70 2014 Quick Reference Guide

5
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock your vehicle, open your liftgate and start the engine.
It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).
The operating range of the Intelligent Key is within

31.5 in (80 cm) from each request switch.
To lock the vehicle, push either door handle request

switch
01 once or press the
button
02 on the key fob.
To unlock the vehicle, perform one of the following procedures:

•
Push either door handle request switch 01 once; the

corresponding door will unlock. Push the door handle
request switch
01 again within 1 minute; all other

doors will unlock, or
•
Press the button
03 on the key fob to unlock the driver’s

side door. Press the
button again; all other doors will

unlock.
To open the liftgate, press the button 04 for more than 1 second.

The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding the

button 05 for more than 1 second. Once activated, the panic alarm and headlights w\
ill stay on
for a period of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery in the Intelligent Key is almost discharged,

the guide light
06 of the Intelligent Key port blinks and

the Intelligent Key insertion indicator 07 is displayed in

the vehicle information display.
To start the engine under these circumstances, insert

the Intelligent Key into the key port with the keyring
side facing backward until it latches into place. Then
push the ignition switch to start the engine.
To remove the Intelligent Key from the port, push the

ignition switch to turn the engine off and then pull the
Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent

Key battery. If you see the Intelligent Key warning light

08 , replace the battery in the Intelligent Key.

Do not insert the mechanical key or other objects into
the key port because it will damage the key port.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)”, “Starting and driving (section 5)” and the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
first drive features
01
02
03
04
05
06
F E
07
08
1354681_14a_Infiniti_QX70_QRG_052813.indd 55/28/13 11:59 AM

12
first drive features
FM/AM/SiriusXM* Satellite Radio with CD/DVD Player
(with Navigation System – if so equipped)
01 VOLUME/ON•OFF CONTROL KNOB
Press the
VOL/ON•OFF control knob to turn the system on or off. Turn the knob right or left



to increase or decrease the volume.
02 SEEK•CAT AND TRACK BUTTONS
To scan quickly through each broadcasting station, press the
SEEK•CAT button or the TRACK



button to stop at the previous or next broadcast station.
For SiriusXM Satellite Radio, press the
SEEK•CAT button or the TRACK button to switch to



the first channel of the previous or next category.

Press the
SEEK•CAT button or the TRACK button to change tracks on a CD.
Press and hold the
SEEK•CAT button or the TRACK button to fast forward or rewind a



track on a CD.
03 TUNE/FOLDER/AUDIO CONTROL KNOB
To manually tune the radio, turn the
TUNE/FOLDER/AUDIO knob left or right.
04 STATION PRESET BUTTONS
Twelve stations can be set for the FM band, six for the AM band and eigh\
teen for SiriusXM




Satellite Radio.
To store a station in a preset, you must first select a radio band by pr\
essing the
AM•FM/SAT



button 05 , then tune to the desired AM, FM or SiriusXM Satellite station.

Then press and hold the desired station preset button
( 1-6) until the sound is briefly



muted. The channel indicator will then display and the sound will resume\
. Programming




is now complete.
To retrieve a previously set station, select the radio band where the pr\
eset was stored,




then press the corresponding station select button
(1-6).
*SiriusXM Satellite Radio is only available on vehicles equipped with op\
tional SiriusXM Satellite subscription service.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your Owner’s Manual.
05
0103
04
02
1354681_14a_Infiniti_QX70_QRG_052813.indd 125/28/13 12:00 PM

17
When speaking Phonebook names, please be aware
some phones require the last name to be spoken
before the first name. For example, “Michael Smith”
may be spoken as “Smith Michael”.
To cancel a voice recognition session, simply wait
5 seconds, say “Cancel” or “Quit”, or press and hold
the
button for 5 seconds.
To increase or decrease the volume of the voice
prompts, push the volume control switches
or on
the steering wheel or turn the VOL/ON•OFF control knob on the audio system while the system
is responding.
If the voice recognition system does not recognize your voice commands, \
train the system
using the Speaker Adaptation Mode. See your Owner’s Manual for detail\
ed information.
For more detailed information and instructions, refer to your cellular p\
hone Owner’s Manual
and visit www.InfinitiUSA.com/Bluetooth.
Bluetooth® System with Navigation* (if so equipped)
CONNECTING PROCEDURE
The vehicle must be stationary when connecting
the phone.
1.


Press the button and select the
“Connect Phone” key.
*Some jurisdictions prohibit the use of cellular telephones while drivin\
g.
Microphone
1354681_14a_Infiniti_QX70_QRG_052813.indd 175/28/13 12:01 PM

19



4.


After the tone, say the name of the person as shown on the vehicle’s \
display of the
phonebook. Depending on the phone, the last name of the contact may need\
to be
spoken before the first name.
MAKING A CALL:



1. Press the button.



2. After waiting for the tone, say “Phone”.



3. After the next tone, say “Dial Number”.



4.


After the next tone, say “123-456-7891”. You may also say the digi\
ts in groups of
3, 3 and 4, respectively. To use this group dialing method, say only the\
first 3 digits of
the phone number instead of all 10 digits. After the system recognizes t\
he number, it
will request the next 3 digits and finally the last 4 digits.



5.


After the system speaks the correct number and sounds the tone, say “\
Dial.”
RECEI

v
ING/ENDING A CALL
To accept the call, press the button on the
steering wheel or touch the “Answer” key.
To reject the call, touch the “Reject Call” key.
To hang-up, press the button or touch the
“Hang-Up” key.
Bluetooth® System without Navigation* (if so equipped)
PAIRING PROCEDURE



1.

Press the button on the steering wheel. The
system announces the available commands.



2.


Say “Connect Phone”. The system acknowledges

the command and announces the next set of
available commands.



3.


Say “Add Phone”. The system acknowledges

the command and asks you to initiate
connecting from the phone handset.



4.


Initiate pairing from the phone.


•

The


connecting procedure varies according to each cellular phone model.

For detailed connecting instructions and a list of compatible phones, pl\
ease visit


www.InfinitiUSA.com/bluetooth.
•

When


prompted for a PIN code, enter “1234” from the handset. (The PIN code is assigned

by INFINITI and cannot be changed.)
*Some jurisdictions prohibit the use of cellular telephones while drivin\
g.
1354681_14a_Infiniti_QX70_QRG_052813.indd 195/28/13 12:01 PM

20
system guide
5. The system asks for a name for the phone. Say “Yes”. The system ac\
knowledges the
command and registers the cellular phone.
PHONEBOOK
Depending on the phone, the system may automatically download the entire\
phonebook. For
more information, please visit www.InfinitiUSA.com/bluetooth or the phone’s user guide.
If the phonebook does not download automatically, 40 entries can be indi\
vidually
downloaded. To manually download entries:



1. Push the button on the steering wheel



2. After the tone, say “Phonebook”.



3. After the next tone, say “Transfer Entry”.



4.


Using the phone, select an entry to send to the vehicle. Please consult \
the website above or

your phone’s User Guide for specific steps of your phone.



5. The system will speak the transferred entry. Confirm the entry by say\
ing “Yes” after the tone.
CALLING A PHONEBOOK ENTRY:
In some cases, names stored using all UPPERCASE letters may not be recog\
nized by the voice
recognition system.



1. Press the button.



2. After waiting for the tone, say “Call”.



3. After the next tone, speak a name of a phonebook entry. For example “\
Michael Smith”.



4. Confirm the correct name is recognized by saying “Dial” after t\
he tone.
MAKING A CALL:



1. Press the button.



2. After waiting for the tone, say “Call”.



3. After the next tone, say “Phone Number”.



4.


After the next tone, say “123- 456- 7890”. You may also say the di\
gits in groups of 3, 3

and 4, respectively. To use this group dialing method, say only the firs\
t 3 digits of the phone
number instead of all 10 digits. After the system recognizes the digits,\
it will request the next
3 digits and finally the last 4 digits.



5. After the system speaks the correct number and sounds the tone, say “\
Dial.”
RECEI

v
ING/ENDING A CALL
To accept the call, press the button on the steering wheel.
To reject the call, press the button.
To hang-up, press the button.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your Owner’s Manual
or please visit www.InfinitiUSA.com/bluetooth.
1354681_14a_Infiniti_QX70_QRG_052813.indd 205/28/13 12:01 PM