torque ISUZU AXIOM 2002 Service User Guide

1A±34
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
3. If the leak is still present, discharge and recover the
refrigerant from the system.
4. Replace the O-rings.

O-rings cannot be reused. Always replace with new
ones.

Be sure to apply the specified compressor oil to the
new O-rings.
5. Retighten the refrigerant line fitting to the specified
torque.

Use two wrenches to prevent twisting and damage
to the line.
6. Evacuate, charge and retest the system.
Leaks In The Hose
If the compressor inlet or outlet hose is leaking, the entire
hose must be replaced. The refrigerant hose must not be
cut or spliced for repair.
1. Locate the leak.
2. Discharge and recover the refrigerant.
3. Remove the hose assembly.

Cap the open connections at once.
4. Connect the new hose assembly.

Use two wrenches to prevent twisting or damage to
the hose fitting.

Tighten the hose fitting to the specified torque.
5. Evacuate, charge and test the system.
Compressor Leaks
If leaks are located around the compressor shaft seal or
shell, replace or repair the compressor.
Recovery, Recycling, Evacuation and
Charging of HFC-134a
Air conditioning systems contain HFC-134a. This is a
chemical mixture which requires special handling
procedures to avoid personal injury.

Always wear safety goggles and protective gloves.

Always work in a well-ventilated area. Do not weld or
steam clean on or near any vehicle-installed air
conditioning lines or components.

If HFC-134a should come in contact with any part of
the body, flush the exposed area with cold water and
immediately seek medical help.

If it is necessary to transport or carry any container of
HFC-134a in a vehicle, do not carry it in the
passenger compartment.

If it is necessary to fill a small HFC-134a container
from a large one, never fill the container completely.
Space should always be allowed above the liquid for
expansion.

HFC-134a and R-12 should never be mixed as their
compositions are not the same.

HFC-134a PAG oil tends to absorb moisture more
quickly than R-12 mineral oil and, therefore, should
be handled more carefully.

Keep HFC-134a containers stored below 40
C
(104
F).WARNING:

SHOULD HFC-134A CONTACT YOUR EYE(S),
CONSULT A DOCTOR IMMEDIATELY.

DO NOT RUB THE AFFECTED EYE(S). INSTEAD,
SPLASH QUANTITIES OF FRESH COLD WATER
OVER THE AFFECTED AREA TO GRADUALLY
RAISE THE TEMPERATURE OF THE
REFRIGERANT ABOVE THE FREEZING POINT.

OBTAIN PROPER MEDICAL TREATMENT AS
SOON AS POSSIBLE. SHOULD THE HFC-134A
TOUCH THE SKIN, THE INJURY MUST BE
TREATED THE SAME AS SKIN WHICH HAS BEEN
FROSTBITTEN OR FROZEN.
Refrigerant Recovery
The refrigerant must be discharged and recovered by
using the J-39500 (ACR4:HFC-134a Refrigerant
Recovery/Recycling/Recharging/System) or equivalent
before removing or mounting air conditioning parts.
1. Connect the high and low charging hoses of the
ACR
4(or equivalent) as shown below.
901R100022
Legend
(1) Low Side
(2) High Side
2. Recover the refrigerant by following the
Manufacturer's Instructions.
3. When a part is removed, put a cap or a plug on the
connecting portion so that dust, dirt or moisture
cannot get into it.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±39
4. Remove serpentine belt.

Move serpentine belt tensioner to loose side using
wrench then remove serpentine belt.
850RY00005
Legend
(1) Auto Tensioner
(2) Idle Pulley
(3) Cooling Fan Pulley
(4) Serpentine Belt
(5) Power Steering Oil Pump
(6) Air Conditioner Compressor
(7) Crankshaft Pulley
(8) Generator
5. Disconnect refrigerant line connector.

When removing the line connector, the connecting
part should immediately be plugged or capped to
prevent foreign matter from being mixed into the
line.
6. Remove compressor.
Installation
1. Install compressor.

Tighten the compressor fixing bolts to the specified
torque.
Torque: 19 Nwm (14 lbwft)
2. Connect refrigerant line connector.

Tighten the refrigerant line connector fixing bolts to
the specified torque.
Torque: 15 Nwm (11 lbwft)

O-rings cannot be reused. Always replace with new
ones.

Be sure to apply new compressor oil to the O-rings
when connecting refrigerant lines.
3. Install serpentine belt.

Move serpentine belt tensioner to loose side using
wrench, then install serpentine belt to normal
position.4. Connect magnetic clutch harness connector.
New Compressor Installation
The new compressor is filled with 150cc (5.0fl.oz.)of
compressor oil and nitrogen gas. When mounting the
compressor on the vehicle, perform the following steps;
1. Gently release nitrogen gas from the new
compressor.

Take care not to let the compressor oil flow out.

Inspect O-rings and replace if necessary.
871RX033
2. Turn the compressor several times by hand and
release the compressor oil in the rotor.
3. When installing on a new system, the compressor
should installed as it is. When installing on a used
system, the compressor should be installed after
adjusting the amount of compressor oil. (Refer to
Compressor in this section)
871RX035

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±41
8. Remove horn (R/LH).
9. Remove front side turn signal light (R/LH).
10. Remove head light (R/LH).
11. Disconnect pressure switch, ambient sensor and
condenser fan connector.
12. Disconnect refrigerant line.

When removing the line connector, the connecting
part should immediately be plugged or capped to
prevent foreign matter from being mixed into the
line.
13. Remove condenser & receiver tank assembly.

Handle with care to prevent damaging the
condenser or radiator fin.
Installation
1. Install condenser & reciver tank assembly.

If installing a new condenser, be sure to add 30cc
(1.0 fl. oz.) of new compressor oil to a new one.

Tighten the condenser fixing bolts to the specified
torque.
Torque: 6 Nwm (52 lb in)
2. Connect refrigerant line.

Tighten the inlet line connector fixing bolt to the
specified torque.
Torque: 15 Nwm (11 lb ft)

Tighten the outlet line connector fixing bolt to the
specified torque.
Torque: 6 Nwm (52 lb in)

O-rings cannot be reused. Always replace with new
ones.

Be sure to apply new compressor oil to the O-rings
when connecting the refrigerant line.
3. Connect pressure switch, ambient sensor and
condenser fan connector.
4. Install head light (R/LH).
5. Install front side turn signal light (R/LH).
6. Install horn (R/LH).
7. Install engine hood front end with engine hood lock &
bumper stay.

Align the setting mark when installing.
8. Install condenser air guide.
9. Install front side bumper retainer (RH).
10. Install front center bumper retainer.
11. Install front bumper assembly.

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±43
Receiver / Drier
Receiver / Drier and Associated Parts
875R200019
Legend
(1) Front Side Turn Signal Light (LH)
(2) Refrigerant Line
(3) Head Light (LH)
(4) Front Bumper Assembly
(5) Receiver / Drier
(6) Pressure Switch Connector
Removal
1. Disconnect the battery ground cable.
2. Discharge and recover refrigerant.

Refer to
Refrigerant Recovery in this section.
3. Remove front bumper assembly.

Refer to the
Front Bumper in Body Structure
section.
4. Remove front side turn signal light (LH).
5. Remove head light (LH).
6. Disconnect pressure switch connector.
7. Disconnect refrigerant line.

When removing the line connected part, the
connecting part should immediately be plugged or
capped to prevent foreign matter from being mixed
into the line.
8. Remove receiver/drier.

Loosen the bolt, then, using care not to touch or
bend the refrigerant line, carefully pull out the
receiver/drier.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. If installing a new receiver/drier, be sure to add 30cc
(1.0 fl. oz.) of new compressor oil to a new one.
2. Put the receiver/drier in the bracket and connect with
the refrigerant line. Check that no excessive force is
imposed on the line. Fasten the bracket bolt to the
receiver/drier.
3. Tighten the refrigerant line to the specified torque.
Torque: 6 Nwm (52 lb in)
4. O-rings cannot be reused. Always replace with new
ones.
5. Be sure to apply new compressor oil to the O-rings
when connecting the refrigerant line.

1A±44
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Pressure Switch
Pressure Switch and Associated Parts
875R200021
Legend
(1) Pressure Switch Connector
(2) Front Side Turn Signal Light (LH)
(3) Head Light (LH)
(4) Front Bumper Assembly
(5) Pressure Switch
Removal
1. Disconnect the battery ground cable.
2. Discharge and recover refrigerant.

Refer to
ªRefrigerant Recovery in this section.
3. Remove the front bumper assembly.

Refer to the
Front Bumper in Body Structure
section.
4. Remove the front side turn signal light (LH).
5. Remove the head light (LH).
6. Disconnect pressure switch connector.
7. Disconnect pressure switch.

When removing the switch connected part, the
connecting part should immediately be plugged or
capped to prevent foreign matter from being mixed
into the line.
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. O-ring cannot be reused. Always replace with a new
one.
2. Be sure to apply new compressor oil to the O-ring
when connecting pressure switch.
3. Tighten the pressure switch to the specified torque.
Torque: 13 Nwm (113 lb in)

1A±46
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
9. Disconnect drain hose.
10. Disconnect refrigerant line.

Use a back-up wrench when disconnecting and
reconnecting the refrigerant lines.

When removing the refrigerant line connected part,
the connecting part should immediately be plugged
or capped to prevent foreign matter from being
mixed into the line.
11. Remove evaporator assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. To install a new evaporator assembly, add 50cc
(1.7 fl. oz.) of new compressor oil to the new core.
2. Tighten the refrigerant outlet line to the specified
torque.
Torque: 25 Nwm (18 lb ft)
3. Tighten the refrigerant inlet line to the specified
torque.
Torque: 15 Nwm (11 lb ft)
4. O-rings cannot be reused. Always replace with new
ones.
5. Be sure to apply new compressor oil to the O-rings
when connecting lines.

1A±48
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)

Lift to remove the upper case.
874R200007
9. Remove evaporator core.
874R200008
10. Remove expansion valve.

Tear off the insulator carefully.

Remove the sensor fixing clip.

Use a back-up wrench when disconnecting all
refrigerant pipes.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. The sensor is installed on the core with the clip.
2. The sensor must not interfere with the evaporator
core.
3. When installing the new evaporator core, install the
duct sensor (2) to the evaporator core (1) specified
position with the clip in the illustration.
874RY00016
4. O-rings cannot be reused. Always replace with new
ones.
5. Be sure to apply new compressor oil to the O-rings
when connecting lines.
6. Be sure to install the sensor and the insulator on the
place where they were before.
7. To install a new evaporator core, add 50cc (1.7 fl. oz.)
of new compressor oil to the new core.
8. Tighten the refrigerant lines to the specified torque.
Refer to
Main Data and Specifications for Torque
Specifications in this section.
9. Apply an adhesive to the parting face of the lining
when assembling the evaporator assembly.

1A±50
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
11. Disconnect discharge line (High-pressure hose)
using a back-up wrench.

Use a backup wrench when disconnecting and
reconnecting the refrigerant lines.

When removing the refrigerant line connecting part,
the connecting part should immediately be plugged
or capped to prevent foreign matter from being
mixed into the line.
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1. O-rings cannot be reused. Always replace with new
ones.
2. Be sure to apply new compressor oil to the O-rings
when connecting lines.
3. Tighten the refrigerant line to the specified torque.
Refer to
Main Data and Specifications for Torque
Specifications in this section.

1A±52
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
Torque Specifications
852R200009
874R200013

HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
1A±53
Compressor
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT LOCATION VIEW IN ORDER TO
DETERMINE WHETHER YOU ARE PERFORMING
SERVICE ON OR NEAR THE SRS COMPONENTS OR
THE SRS WIRING. WHEN YOU ARE PERFORMING
SERVICE ON OR NEAR THE SRS COMPONENTS OR
THE SRS WIRING, REFER TO THE SRS ON-VEHICLE
SERVICE INFORMATION. FAILURE TO FOLLOW
CAUTIONS COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
General Description
When servicing the compressor, keep dirt or foreign
material from getting on or into the compressor parts and
system. Clean tools and a clean work area are important
for proper service. The compressor connections and the
outside of the compressor should be cleaned before any
ºOn±Vehicleº repair, or before removal of the
compressor. The parts must be kept clean at all times and
any parts to be reassembled should be cleaned with
Trichloroethane, naphtha, kerosene, or equivalent
solvent, and dried with dry air. Use only lint free cloths to
wipe parts.
The operations described below are based on bench
overhaul with compressor removed from the vehicle,
except as noted. They have been prepared in order of
accessibility of the components. When the compressor is
removed from the vehicle for servicing, the oil remaining
in the compressor should be discarded and new
compressor oil added to the compressor.
Compressor malfunction will appear in one of four ways:
noise, seizure, leakage or low discharge pressure.
Resonant compressor noises are not cause for alarm;
however, irregular noise or rattles may indicate broken
parts or excessive clearances due to wear. To check
seizure, de±energize the magnetic clutch and check tosee if the drive plate can be rotated. If rotation is
impossible, the compressor is seized. Low discharge
pressure may be due to a faulty internal seal of the
compressor, or a restriction in the compressor. Low
discharge pressure may also be due to an insufficient
refrigerant charge or a restriction elsewhere in the
system. These possibilities should be checked prior to
servicing the compressor. If the compressor is
inoperative, but is not seized, check to see if current is
being supplied to the magnetic clutch coil terminals.
The compressor oil used in the HFC±134a system
compressor differs from that used in R±12 systems.
Also, compressor oil to be used varies according to the
compressor model. Be sure to avoid mixing two or more
different types of oil.
If the wrong oil is used, lubrication will be poor and the
compressor will seize or malfunction.
DKV-14G Type Compressor
DKV±14G is equipped with five±vane rotary compressor.
These vanes are built into a rotor which is mounted on a
shaft.
When the shaft rotates, the vanes built into the cylinder
block assembly are operated by centrifugal force.
This changes the volume of the spare formed by the rotor
and cylinder, resulting in the intake and compression of
the refrigerant gas. The discharge valve and the valve
stopper, which protects the discharge valve, are built into
the cylinder block assembly. There is no suction valve but
a shaft seal is installed between the shaft and head; a
trigger valve, which applies back pressure to the vanes, is
installed in the cylinder block and a refrigerant gas
temperature sensor is installed in the front head.
The specified quantity of compressor oil is contained in
the compressor to lubricate the various parts using the
refrigerant gas discharge pressure.
871RX002