immobilizer ISUZU TF SERIES 2004 Workshop Manual

6E-92 3.5L ENGINE DRIVEABILITY AND EMISSIONS

2.Demand of Data
1.
Connect Tech-2 to the vehicle. When activated b
y
turning on the power of Tech-2, push the "Enter"
switch.
2.
Turn on the ignition switch (without starting the
engine)
3.
In the main menu of Tech 2, push "F1: Service
Programming System (SPS)".
4.
Push "F0: Request Info" of Tech-2.

5.
Where vehicle data has been already saved in
Tech-2, the existing data come on display. In this
instance, as Tech-2 starts asking whether to keep
the data or to continue obtaining anew data from
the control unit, choose either of them.





6.
If you select “continue”, you have to select “Model
Year”, “Vehicle Type”.
7.
After that. then push button and turn Ignition switch
tuned on, off, on following Tech-2 display. Tech-2
will read information from controller after this
procedure.
8.
During obtaining information, Tech-2 is receiving
information from the control unit ECM and TCM
(A/T only) at the same time. With VIN not being
programmed into the new control unit at the time
of shipment, "obtaining information" is not
complete (because the vehicle model, engine
model and model year are specified from VIN). Fo
r
the procedure get additional information on
vehicles, instruction will be provided in dialog form,
when TIS2000 is in operation.
9.
Following instructions by Tech-2, push the "Exit"
switch of Tech-2, turn off the ignition of the vehicle
and turn off the power of Tech-2, thereby removing
from the vehicle.


3.Data Exchange
1.
Connect Tech-2 to P/C, turn on the power and
click the "Next" button of P/C.
2. Check VIN of the vehicle and choose "Next".
3. Select “System Type” for required control unit.


Engine (Programming for ECM or PCM)


Transmission (Programming for TCM)
4.
When a lack of data is asked from among the
following menu, enter accordingly.

Select following Menu


Model Year


Model


Engine type


Transmission type


Destination code (vehicles for general export)*1


Immobilizer
Etc.
* 1: How to read the destination code
"Destination code can be read from service ID Plate
affixed on vehicles, while on service ID plate the
destination code is described at the right-hand edge o
f
Body Type line. In the figure, the destination code can
be read as "RR3" (Australia).

6E-100 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Step Action Value (s) Yes No
11
Using the DVM and check the data link connector
communication circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the ECM connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?






E-61(B)
B-58



-
Repair faulty
harness and
verify repair
Go to Step 12
12
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)"
.
Was the problem solved?
-
Verify repair
Go to Step 13
13
Replace the ECM.
Is the action complete?
IMPORTANT:
The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the Immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement”
for the
ECM/Immobilizer linking procedure.
-
Verify repair
-

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E -103

Step
Action Value (s) Yes No
6
Replace the ECM.
Is the action complete?
IMPORTANT:
The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the Immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement”
for the
ECM/Immobilizer linking procedure.
-
Verify repair
-

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E -105

Check Engine Lamp (MIL) “ON" Steady

Step Action Value (s) Yes No
1
1. Ignition "Off", engine "Off".
2. Disconnect the ECM connector.
3. Ignition "On".
Was the "CHECK ENGINE" lamp turned on?
- Go to Step 2
Go to Step 4

2
Using the DVM and check the "CHECK ENGINE"
lamp circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the meter connector and ECM
connector.
3. Check the circuit for short to ground circuit.
Was the problem found?


B-24



E-61(B)


- Verify repair Go to Step 3

3
Replace the meter assembly.
Is the action complete?
- Verify repair -
4
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)"
.
Was the problem solved?
-
Verify repair
Go to Step 5
5
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the Immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement”
for the
ECM/Immobilizer linking procedure.
-
Verify repair
-

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-115
Step Action Value (s) Yes No
13
Using the DVM and check the fuel pump ground
circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the fuel pump connector.
3. Check the circuit for open circuit.
Was the DVM indicated specified value?
F-2





Continuity Go to Step 15 Go to Step 14
14
Repair the open circuit between the fuel pump and
body ground.
Is the action complete?
F-2
C-109


- Verify repair -
15
Replace the fuel pump.
Was the problem solved?
- Verify repair Go to Step 16
16
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 17
17
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-129
Step Action Value (s) Yes No
28
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 29
29
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-141
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up) Recovery Condition Related Failure Parts Related
ECM Pin
No. Related
Multiple
DTC
P1626 - Immobilizer No Signal No response from immobilizer control unit.
1. ECM and immobilizer control unit
communication circuit open circuit, short to
ground circuit or short to voltage circuit.
2. Electrical interference.
3. Magnetic interference.
4. ECM malfunction.
5. Immobilizer control unit malfunction.
6. Transponder key malfunction. B18/
B32 B**** P1631 - Immobilizer Wrong Signal Received response is not correct.
1. ECM malfunction.
2. Immobilizer control unit malfunction.
3. Transponder key malfunction. - B**** P1648 - Wrong Security Code Entered Received incorrect security code.
1. ECM malfunction.
2. Immobilizer control unit malfunction.
3. Transponder key malfunction. - B****
67
P1649 - Immobilizer Function Not
Programmed Immobilizer function is not programmed in the
ECM. 1. Engine does not start.
2. Check engine lamp flash.
No recovery
ECM malfunction. - B****

6E-148 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
8
Using the DVM and check the MAF sensor signal
circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the MAF sensor connector.
3. Ignition "On".
4. Check the circuit for short to power supply circuit.
Was the DVM indicated specified value?
V

E-63


Less than 1V
Go to Step 9
Repair faulty
harness and
verify repair
9
Check any accessory parts which may cause electric
interference.
- Remove the
accessory parts
and verify repair
Go to Step 10
10
Check the shield wire for open or short circuit.
Was the problem found?
- Verify repair Go to Step 11
11
Substitute a known good MAF & IAT sensor assembly
and recheck.
Was the problem solved?
- Go to Step 12 Go to Step 13
12
Replace the MAF & IAT sensor assembly.
Is the action complete?
- Verify repair
13
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 14
14
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-153
Step Action Value (s) Yes No
11
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-157
Step Action Value (s) Yes No
7
Using the DVM and check the MAF sensor ground
circuit.
1. Ignition "On", engine "Off".
2. Disconnect the MAF sensor connector .
3. Check the circuit for short to power supply circuit.
Was the DVM indicated specified value?
E-63
V




Less than 1V
Go to Step 8
Repair faulty
harness and
verify repair
8
Using the DVM and check the MAF sensor signal
circuit.
1. Ignition "On", engine "Off".
2. Disconnect the MAF sensor connector.
3. Check the circuit for short to power supply circuit.
Was the DVM indicated specified value?
E-63
V




Less than 1V
Go to Step 11
Repair faulty
harness and
verify repair
9
Substitute a known good MAF & IAT sensor assembly
and recheck.
Was the problem solved?
- Go to Step 10 Go to Step 11
10
Replace the MAF & IAT sensor assembly.
Is the action complete?
- Verify repair -
11
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 12
12
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -