oil viscosity ISUZU TF SERIES 2004 User Guide

MAINTENANCE AND LUBRICATION 0B-1
SECTION 0B
MAINTENANCE AND LUBRICATION
TABLE OF CONTENTS
PAGE
Maintenance Schedule (For GENERAL EXPORT) ......................................................... 0B- 2
Maintenance Schedule (For EUROPE) ........................................................................... 0B- 5
Severe Conditions Maintenance Schedule (For GENERAL EXPORT) ........................ 0B-11
Severe Conditions Maintenance Schedule (For EUROPE) .......................................... 0B-12
Recommended Fluids and Lubricants (For GENERAL EXPORT)................................ 0B-13
Recommended Fluids and Lubricants (For EUROPE).................................................. 0B-15
Oil Viscosity Chart ........................................................................................................... 0B-16

0B-16 MAINTENANCE AND LUBRICATION
OIL VISCOSITY CHART
Lubricants should be carefully selected according to the lubrication chart. It is also important to select viscosity of
lubricants according to the ambient temperature by referring to the following table.

OIL VISCOSITY CHART FOR DIESEL ENGINE
APPLY DIESEL ENGINE OIL

(Single grade)VISCOSITY GRADE - AMBIENT TEMPERATURE
-25 C -15 C -10 C
32 F 5 F -13 F 77 F
0 C 30 C
86 F
*Not recomended for sustained high speed driving.
SAE 30
SAE 10W-30
SAE 15W-40, 20W-40, 20W-50
SAE 5W-30
SAE 20, 20W
SAE 10W
SAE 40, 50
25 C
15 C
(Multi grade)
*
60 F 14 F
ED-03







OIL VISCOSITY CHART FOR GASOLINE ENGINE
APPLY GASOLINE ENGINE OIL


(Malti grade)

MAINTENANCE AND LUBRICATION 0B-17

OIL VISCOSITY CHART FOR TRANSMISSION CASE


OIL VISCOSITY CHART FOR FRONT AXLE AND REAR AXLE

7D1-34 TRANSFER CONTROL SYSTEM

Diagnosis
Before determining a trouble (Non-trouble mode)
1. When shifting from 2H to 4H:
1-1-1 When the flashing frequency of the 4WD indicator is changed from 2Hz to 4Hz (Shft on the fly)
If the load is too large to shift the gears synchronously, the operation is repeated up to 3 times. If the shifting
is not effected after being repeated 3 times, the indicator frequency is changed from 2Hz to 4Hz and, at the
same time, the actuator condition is changed to 2H, indicator flashes at 4Hz for 10 seconds, and then goes
out.
Cause of excessive synchronous shifting load

Extremely low temperature (the oil viscosity of the front differential increases requiring a large load for
synchronization)
 High speed (since the difference of relative revolutions of gears to be shifted synchronously is too large,
required work load per unit time becomes larger).
Step 1-1-1:
Stop the vehicle or decrease the speed and operate as required again.

1-1-2 When the flashing frequency of the 4WD indicator is changed from 2Hz to 4Hz (Rigid and free wheel
Hub) / Block out of meshing spline.
Step 1-1-2:
Run the vehicle forward and backward several meters and operate as required again.

1-2 When the flashing of 4WD indicator at 2Hz continues more than 11.5 seconds (repetition of 3 times of
above No.1 is counted) (Shift on the fly)
If there is difference of revolutions and phases between the front wheel and axle, connecting the front wheel
and axle is difficult.
Until shifting in the transfer and connection of the front wheel and axle are completed

, the indicator flashes
at a frequency of 2Hz. In the above case, the indicator continues flashing at a frequency of 2Hz until the
connection of the front axle is completed. (If the shifting in the transfer is not completed, the flashing
frequency is changed to 4Hz (above No.1).)
By correcting the difference of relative revolutions and deviation of phases, the shifting can be completed.
Step 1-2:
While the vehicle is running, make sure of safety around the vehicle and accelerate or decelerate the
vehicle while going straight.
When the vehicle is at a stop, run the vehicle forward and backward several meters.

2.
When shifting from 4H to 2H
2-1 When 4WD indicator continues flashing at 2Hz
When shifting from 4H to 2H, the 4WD indicator continues flashing at 2Hz until separation in the transfer and
the separation of the front wheel axle are completed
. When torsional torque is accumulated in the drive
system, separation in the transfer and separation of the front axle
is difficult. In such a case, they can be
separated by removing the torsional torque of the drive system.
Step 2-1:
While the vehicle is running, make sure of safety around the vehicle and accelerate or decelerate the
vehicle while going straight.
When the vehicle is in stop, run the vehicle several meters forward and backward.


: Shift on the fly only.