reverse ISUZU TF SERIES 2004 Workshop Manual
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2004, Model line: TF SERIES, Model: ISUZU TF SERIES 2004Pages: 4264, PDF Size: 72.63 MB
Page 4134 of 4264
7A2-142 DIAGNOSIS (JR405E)
1. Oil Cooler Out
2. R Range Line Pressure Detection Port
(Low & Reverse Brake Pressure Detection Port)
3. D, 3, 2 & L Range Line Pressure Detection Port
(Low Clutch Pressure Detection Port)
4. Oil Cooler In
4. If the line pressure is lower than standard value at
idling in L and R ranges.
ATF leaking from low and reverse brake hydraulic
circuit.
5. If the line pressure is higher than standard value at
idling in all ranges.
Throttle opening signal reception error.
Faulty oil temperature sensor.
Faulty operation of low clutch solenoid.
Sticking pilot valve.
Sticking pressure regulator valve or plug.
6. If the line pressure is lower than standard value at stall
speed in all ranges.
Throttle opening signal reception error.
Faulty operation of line pressure solenoid.
Faulty operation of low clutch solenoid.
Sticking pilot valve.
Sticking pressure regulator valve or plug.
Page 4135 of 4264
DIAGNOSIS (JR405E) 7A2-143
TIME LAG TEST
Procedure
1. Chock the four wheels.
2. Warm up the engine.
3. Apply the parking brake.
4. Step on the foot brake fully.
5. Set the select lever from N to D or N to R range.
6. Record the time from when moving the select button until
feeling shock.
Time Lag
Standard:
N to D Range: Below 0.7 Seconds
N to R Range: Below 1.2 Seconds
Evaluation
1. If the time lag is out of standard value when shifting N
to D range.
Forward range line pressure is low.
Slip of low clutch.
Slip of low one-way clutch.
Trouble in control valve body (faulty operation, sticking,
clogged oil passage).
Faulty low clutch duty solenoid operation.
Shortage or faulty quality of ATF.
2. If the time lag is out of standard value when shifting N
to R range.
Reverse range line pressure is low.
Slip of low & reverse brake.
Slip of reverse clutch.
Trouble in control valve body (faulty operation, sticking,
clogged oil passage).
Faulty low & reverse brake duty solenoid operation.
Shortage or faulty quality of ATF.
Page 4137 of 4264
DIAGNOSIS (JR405E) 7A2-145
5. R range test.
1) Shift into the R range and while starting at full throttle,
check for slipping.
6.P range test.
1) Stop the vehicle on a grade and after shifting into the P
range, release the parking brake. Then check to see tha
t
the parking lock pawl holds the vehicle in place.
Select
Lever
Position
Gear
Position
Gear
Shift
P
R Reverse
N
D 1st
2nd
3rd
4th
3 1st
2nd
3rd
4th(*1)
2 1st
2nd
3rd(*1)
4th(*1)
L 1st
2nd(*1)
3rd(*1)
4th(*1)
Evaluation
1. If there is no 1 to 2 up-shift.
2-4 brake malfunction.
2-4 brake hydraulic circuit failed.
2-4 brake duty solenoid stick.
Refer to symptom diagnosis "No. D1: Faulty Gea
r
Shifting" or DTC section "Gear Ratio Error".
2. If there is no 2 to 3 up-shift.
High clutch malfunction.
High clutch hydraulic circuit failed.
High clutch duty solenoid stick.
Refer to symptom diagnosis "No. D1: Faulty Gea
r
Shifting" or DTC section "Gear Ratio Error".
3. If there is no 2 to 4 (O/D) up-shift.
2-4 brake malfunction.
2-4 brake hydraulic circuit failed.
2-4 brake duty solenoid stick.
Refer to symptom diagnosis "No. D1: Faulty Gea
r
Shifting" or DTC section "Gear Ratio Error".
4. If there is no lock-up in 2, 3 and 4.
Lock-up piston malfunction.
Lock-up hydraulic circuit failed.
Lock-up duty solenoid stick.
Refer to symptom diagnosis "No. I1: No Lock-up"o
r
DTC section "Lock-up Duty Solenoid Failure".
*1: Transmission is shifted at high speed to
prevent engine over-run.
Page 4138 of 4264
7A2-146 DIAGNOSIS (JR405E)
5. If there is no reverse.
Reverse clutch malfunction.
Reverse clutch hydraulic circuit failed.
Low & reverse brake hydraulic circuit failed.
Low & reverse brake duty solenoid stick.
Refer to symptom diagnosis "No. A2: Vehicle Dose Not
Run in R Range" or DTC section "Low & Reverse
Brake Duty Solenoid Failure".
6. If there is no parking.
Parking pawl malfunction.
Refer to symptom diagnosis "No. G1: Vehicle Moves in
P Range or Parking Gear in Not Disengaged othe
r
than P Range".
NOTE:
The check for the cause of abnormal noise and vibration
must be made with extreme care as it could also be due to
loss of balance in propeller shaft, differential, the torque
converter, etc. Or insufficient bending, rigidity, etc. in the
powertran.
Page 4148 of 4264
7A2-156 DIAGNOSIS (JR405E)
No. Wire
Color Pin Name Input /
OutputConnected toMeasurement
Item Measurement
Condition StandardInspection
Point at
Trouble
At lamp OFF 10 – 14.5V Related
harness A24 GRN/
YEL Power Drive Select Switch InputPower drive
switch Voltage
At lamp ON Less than 2V Lamp
At other than
2nd or 4th
gear More than 10
V Related
harness
B1 RED/
YEL 2-4 Brake Pressure Switch Input2-4 brake
pressure switch Voltage
At 2nd or 4th
gear Less than 2VPressure
switch
At 2 range 10 – 14.5V Related
harness
B2 PNK/
BLK 2 Range Switch Input Inhibitor switch Voltage
At other than
2 range Less than 2VInhibitor
switch
InputRelated
harness
B3 BRN/
RED Turbine Sensor
Turbine sensor Voltage (Wave
form) At run in L
range in 1st
gear 20 km/h.
Circuit tester
(+) to B3 pin,
(-) to B5 pin. Pulse
generated (At
AC range
approx. 6.5V)Turbine
sensor
ATF temp.
20C Approx. 1.55
V Related
harness
B4 BLU ATF Thermo Sensor InputATF thermo
sensor Voltage
ATF temp.
60C Approx. 0.7VThermo
sensor
B5 BLK Ground - Ground Voltage Normally Less than 2VRelated
harness
Related
harness
B6 BLU/
BLK Low & Reverse Brake Duty Solenoid OutputLow & reverse
brake duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B6 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B7 BLK/
YEL 2-4 Brake Duty Solenoid Output2-4 brake duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B7 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B8 RED High Clutch Duty Solenoid OutputHigh clutch duty
solenoid Voltage (Wave
form) P, N range.
Circuit tester
(+) to B8 pin,
(-) to B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
Related
harness
B9 WHT/
RED Low Clutch Duty Solenoid OutputLow clutch duty
solenoid Voltage (Wave
form) 4th gear in D
range. Circuit
tester (+) to
B9 pin, (-) to
B22 pin. Pulse
generated (At
AC range
approx. 6.2V)Duty solenoid
At N range 10 – 14.5V Related
harness
B10 RED/
BLK N Range Switch Input Inhibitor switch Voltage
At other than
N range Less than 2VInhibitor
switch
At D range 10 – 14.5V Related
harness
B11 BLU D Range Switch Input Inhibitor switch Voltage
At other than
D range Less than 2VInhibitor
switch
Page 4149 of 4264
DIAGNOSIS (JR405E) 7A2-157
No. Wire
Color Pin Name Input /
OutputConnected toMeasurement
Item Measurement
Condition StandardInspection
Point at
Trouble
At other than
R range, L
range 1st gear More than 10
V Related
harness
B12 YEL Low & Reverse Brake Pressure Switch InputLow & reverse
brake pressure
switch Voltage
At R range, L
range 1st gear Less than 2VPressure
switch
Related
harness
B13 YEL/
RED Vehicle Speed Sensor InputVehicle speed
sensor Voltage (Wave
form) At run in L
range in 1 st
gear 20 km/h.
Circuit tester
(+) to B13 pin,
(-) to B5 pin. Pulse
generated (At
AC range
approx. 6.8V)Vehicle
speed sensor
B14 BLU/
BLK ATF Thermo Sensor Ground - ATF thermo
sensor Continuity Normally Continuity Related
harness
B15 BLK Ground - Ground Voltage Normally Less than 2VRelated
harness
B16 - - - - - - - -
At lock-up.
Circuit tester
(+) to B17 pin,
(-) to B5 pin. Pulse
generated (At
AC range
approx. 2.2 -
9.0V) Related
harness
B17 BLK Lock-up Duty Solenoid OutputLock-up duty
solenoid Voltage (Wave
form)
At unlock-up.
Circuit tester
(+) to B17 pin,
(-) to B5 pin. Pulse
generated (At
AC range
approx. 1.0 -
2.0V) Duty solenoid
At key switch
ON 10 – 14.5V Related
harness
B18 WHT V ign (Ignition Power Supply) Input Key switch Voltage
At key switch
OFF Less than 2V Fuse
At R range 10 – 14.5V Related
harness
B19 RED/
YEL R Range Switch Input Inhibitor switch Voltage
At other than
R range Less than 2VInhibitor
switch
At other than
3rd or 4th
gear More than 10
V Related
harness
B20 WHT/
BLK High Clutch Oil Pressure Switch InputHigh clutch
pressure switch Voltage
At 3rd or 4th
gear Less than 2VPressure
switch
At L range 10 – 14.5V Related
harness
B21 PNK/
BLK L Range Switch Input Inhibitor switch Voltage
At other than
L range Less than 2VInhibitor
switch
B22 GRY/
RED Ground Return Output Shift solenoid Continuity Normally Continuity Related
harness
At N range 10 – 14.5V Related
harness
B23 VIO Line Pressure Solenoid OutputLine pressure
solenoid Voltage
At D range
stall Less than 2V Solenoid
Page 4151 of 4264
DIAGNOSIS (JR405E) 7A2-159
Low & Reverse Brake Duty Solenoid Reference Wave Form
Measurement Terminal: B6 (+) B22 (-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: P, N range in idle
0V2-4 Brake Duty Solenoid Reference Wave Form
Measurement Terminal: B7 (+) B22 (-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: P, N range in idle
0V
High Clutch Duty Solenoid Reference Wave Form
Measurement Terminal: B8 (+) B22 (-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: P, N range in idle
0VLow Clutch Duty Solenoid Reference Wave Form
Measurement Terminal: B9 (+) B22 (-)
Measurement Scale: 5V/div 10ms/div
Measurement Condition: D range 4th gear
0V
Lock-up Duty Solenoid Reference Wave Form
Measurement Terminal: B17 (+) B5 (-)
Measurement Scale: 10V/div 5ms/div
Measurement Condition: Unlock-up condition
0VLock-up Duty Solenoid Reference Wave Form
Measurement Terminal: B17 (+) B5 (-)
Measurement Scale: 10V/div 5ms/div
Measurement Condition: Lock-up condition
0V
Page 4156 of 4264
7A3-4 ON-VEHICLE SERVICE (JR405E)
TRANSMISSION CONTROL MODULE (TCM)
RTW37ALF001901
Remove and Disconnect
1. Disconnect the negative battery cable.
2. Remove the connectors.
3. Remove the fixing nuts and remove the TCM (1)
from the bracket.
Note:
The TCM is fitted under instrument panel of the driver’s
compartment by means of three stud bolts.
Install or Connect
Follow the removal steps in the reverse order. Be
absolutely sure that the connectors are securely
fastened.
AT CONT
Page 4168 of 4264
7A3-16 ON-VEHICLE SERVICE (JR405E)
SOLENOIDS, OIL PRESSURE SWITCH AND OIL TEMPERATURE
SENSOR
244L300003
Legend
1. High clutch oil pressure switch connector
(wire color: Gray)
2. 2-4 brake oil pressure switch connector
(wire color: Brown)
3. Low and reverse brake oil pressure switch connector
(wire color: White)
4. Low and reverse brake duty solenoid connector
(wire color: Pink and White)
5. High clutch duty solenoid connector
(wire color: Green and Gray)
6. Lock-up duty solenoid connector
(wire color: Yellow and Black)
7. 2-4 brake duty solenoid connector
(wire color: Blue and Brown)
8. Low clutch duty solenoid connector
(wire color: Orange and Black)
9. Line pressure solenoid connector
(wire color: Pink)
Page 4175 of 4264
UNIT REPAIR (JR405E) 7A4-1
SECTION 7A4
UNIT REPAIR (JR405E)
TABLE OF CONTENTS
PAGE
Automatic Transmission Disassembly ..................................................................... 7A4 - 2
Control Valve Assembly ............................................................................................ 7A4 - 11
Control Valve Upper Body ........................................................................................ 7A4 - 18
Control Valve Lower Body ........................................................................................ 7A4 - 23
Oil Pump Assembly ................................................................................................... 7A4 - 28
Clutch Pack (Reverse and High Clutch Assembly) ................................................. 7A4 - 33
Carrier and Low Clutch Assembly ........................................................................... 7A4 - 41
Transmission Case .................................................................................................... 7A4 - 54
Bearing and Bearing Race Installation Position ..................................................... 7A4 - 66
Automatic Transmission Reassembly ..................................................................... 7A4 - 69
Service Standard ....................................................................................................... 7A4 - 83
Special Service Tool .................................................................................................. 7A4 - 85