Trans axle ISUZU TF SERIES 2004 Owner's Manual

TRANSFER CASE 7D-3

General Description

RUW34DLF000701
The transfer case is used to provide a means of
providing power flow to the front axle. The transfer case
also provides a means of disconnecting the front axle,
providing better fuel economy and quieter operation
when the vehicle is driven on improved roads where
four wheel drive is not required. In addition, the transfer
case provides an additional gear reduction when placed
in low range, which is useful when difficult off-road
conditions are encountered.
Use the 4WD switch on the center cluster panel to
select the drive range. The 4WD indicator lamp will be
lit when 4WD is selected.

TRANSFER CASE 7D-33

Main Data and Specifications
General Specifications
Type Synchronized type gears shifting between the 2 and 4 wheel drive mode.
Planetary type gears shifting between “low" and “high".
Control method Remote control with the button switch on the instrument panel for gears
shifting among “2H" , “4H" and “4L".
Gear ratio High; 1.000
Low; 2.482
Oil capacity 1.3 lit. (1.37 U.S. quart)
Type of lubricant BESCO GEAR OIL TRANSAXLE (5W-30)
Refer to chart in Section 0

Torque Specifications
Nm (kgm/lb ft)

RTW47DLF000201

7D1-4 TRANSFER CONTROL SYSTEM
Summary of transfer control system
The transfer control system switches between the 2-wheel
drive (2H), 4-wheel drive high-speed (4H), 4-wheel drive low-
speed (4L), and neutral positions electrically when the driver
operate the switches.
This system has following functions.
1. Connection or disconnection of drive force distribution to
the front wheel front shaft (axle shaft) (The drive force
distribution to the front propeller is connected o
r
disconnected with the motor actuator.)
2. Try to repeat the connection or disconnection of the front
wheel drive function as described above.
3. Option: Shift on the fly type only.
Instruction of connection or disconnection of the drive force
transmission between the front wheel axle (axle shaft) and
front wheel
(The motor actuator connects or disconnects the left front
wheel ad front wheel axle (axle shaft).).
4. Shifting of auxiliary transmission gears, connection o
r
disconnection of wheel and engine drive force (4H, 4L,
neutral).
5. Operation of indicator on the instrument panel.
6. Transmission of position signal to other controllers.

TRANSFER CONTROL SYSTEM 7D1-11
Function of Switch and indicator Lamp
Transfer-related indicator lamp and switch function

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
2H Off Off Off Off No
operation 1,0,1,0 Open Open Open -----
4H start
of
operation Off Off Off Off 4H position
for 0.1
second 1,0,1,0 Open Open Open Switch
operation
sensor
Start of
operation Blinking
(2HZ) Off Off Off No
operation 1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
while
driving
During
operation
(Synchro) Blinking
(2HZ) Off Off Off No
operation 1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
using
synchro
and
retrial
During
operation
(Axle
drive) Blinking
(2HZ) Off Off Off No
operation 0,0,1,1 Closed Open Open Axle drive
Axle
waiting Blinking
(2HZ) Off Off Off No
operation 0,0,1,1 Closed Open Open Axle drive
4H On Off Off Off No
operation 0,0,1,1 Closed Open Closed -----
4L start
of
operation On Off Off Off 4L position
for 0.1
second 0,0,1,1 Closed Open Closed Switch
operation
sensor
Start of
operation On Blinking
(2HZ) Off Off No
operation 0,0,0,1
0,1,0,1 Closed Open Closed 4H to 4L
while
driving
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation 0,0,0,1
0,1,0,1 Closed Closed Closed 4H to 4L
through
neutral
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation 0,1,0,0 Closed Closed Closed 4H to 4L
through
neutral
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation 1,1,0,0 Closed Closed Closed 4H to 4L
through
neutral
4L
waiting On Blinking
(2HZ) Off Off No
operation 1,1,0,1 Closed Closed Closed 4H to 4L
while
waiting
4L On On Off Off No
operation 1,1,0,1 Closed Open Closed -----
4H start
of
operation On Off Off Off 4H position
for 0.1
second 1,1,0,1 Closed Open Closed Switch
operation
sensor

7D1-12 TRANSFER CONTROL SYSTEM
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
During
operation On Blinking
(2HZ) Off Off No
operation 1,1,0,1 Closed Open Closed 4L to 4H
while
driving
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation 1,1,0,0 Closed Closed Closed 4L to 4H
through
neutral
During
operation Off Blinking
(2HZ) Off Off No
operation 0,1,0,1
0,0,0,1 Closed Closed Closed 4L to 4H
while
driving
4H
waiting Off Blinking
(2HZ) Off Off No
operation 0,0,1,1 Closed Closed Closed
4L to 4H
while
waiting
4H On Off Off Off No
operation 0,0,1,1 Closed Open Closed -----
2H start
of
operation On Off Off Off 2H position
for 0.1
second 0,0,1,1 Closed Open Closed Switch
operation
sensor
Start of
operation Blinking
(2HZ) Off Off Off No
operation 0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Closed Open Closed 2H to 4H
while
driving
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation 0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Open Open Closed Axle drive
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation 1,0,1,0 Open Open Closed Axle
waiting
2H Off Off Off Off No
operation 1,0,1,0 Open Open Open -----

TRANSFER CONTROL SYSTEM 7D1-13
2H to 4H retrial

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----
4H start
of
operation Off Off Off Off 4H
position
for 0.1
second 1,0,1,0 Open Open Open -----
Start of
operation Blinking
(2HZ) Off Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
while
driving
During
operation
(Synchro)
(Go to 4H
if synchro
complete) Blinking
(2HZ) Off Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
using
synchro
and retrial
X 2
Abandon
ed
operation
(2H) Blinking
(4HZ) Off Off Off No
operation1,0,1,0 Open Open Open Return to
2H
2H
indication
after
10second
s
Off Off Off Off No
operation1,0,1,0 Open Open Open -----

 Completion of transfer case H-L area and axle shift timing may cause some variation in 2Hz blinking pattern.

7D1-14 TRANSFER CONTROL SYSTEM
Operational limits (4H




4L) (Vehicle speed, engine speed, and transmission position not specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4H On Off Off Off Open 0,0,1,1 Closed Open Closed -----
4H start
of
operation On Off Off Off 4L
position
for 0.1
second 0,0,1,1 Closed Open Closed -----
10
second
display
during
limitation On Blinking
(4HZ) Off Off Open 0,0,1,1 Closed Open Closed No
operation
during
limitation
Go to 4H
after 10
seconds
On Off Off Off Open 0,0,1,1 Closed Open Closed -----

Operational limits (4L





4H) (Vehicle speed, engine speed, and transmission position not specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4L On On Off Off No
operation1,1,0,1 Closed Open Closed -----
4L start of
operation On On Off Off 4H
position
for 0.1
second 1,1,0,1 Closed Open Closed -----
10
second
display
during
limitation On Blinking
(4HZ) Off Off Open 1,1,0,1 Closed Open Closed No
operation
during
limitation
Go to 4L
after 10
seconds
On On Off Off No
operation1,1,0,1 Closed Open Closed -----


Under some conditions, a secondary operational indication may be received when the 4Hz operational indication
is present.

TRANSFER CONTROL SYSTEM 7D1-15
Transfer-related indicator lamp and switch function
Skip operation
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detectio
n (limit)
switches
LS1,
LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummy Remarks
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----
4L start of
operation Off Off Off Off 4L
position
for 0.1
second 1,0,1,0 Open Open Open Switch
operation
sensor
Start of
operation Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
while
driving
During
operation
(Synchro) Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
using
synchro
and retrial
During
operation
(Passing
through
4H) Off Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
During
operation
(Passing
through
4H) Off Blinking
(2HZ) Off Off No
operation0,0,1,1
0,1,0,1 Closed Open Open -----
During
operation
(N)
On Blinking
(2HZ) Off Off No
operation
0,0,1,1
0,1,0,1 Closed Open Closed -----
During
operation
(N) On Blinking
(2HZ) Off Off No
operation0,1,0,0 Closed Open Closed Switch
operation
sensor
During
operation
(N) On Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Closed 4H to 4L
while
driving
During
operation
(Axle
drive) Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
Axle
waiting Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
4L waiting On Blinking
(2HZ) Off Off No
operation1,1,0,1 Closed Closed Closed 4H to 4L
while
waiting
4L On On Off Off No
operation1,1,0,1 Closed Open Closed -----

7D1-16 TRANSFER CONTROL SYSTEM
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
lamp 4WD
switch Actuator
detectio
n (limit)
switches
LS1,
LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummy Remarks
2H start of
operation On On Off Off 2H
position
for 0.1
second 1,1,0,1 Closed Open Closed Switch
operation
sensor
During
operation Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation1,1,0,1 Closed Open Closed 4L to 4H
while
driving
During
operation
(Passing
through
N) On Blinking
(2HZ) Off Off No
operation1,1,0,0 Closed Closed Closed 4L to 4H
through
neutral
During
operation
(Passing
through
N) Off Blinking
(2HZ) Off Off No
operation0,1,0,0 Closed Closed Closed 4L to 4H
through
neutral
During
operation
(4H
waiting) Off Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Closed Closed 4L to 4H
while
waiting
During
operation
(Axle) Off while
waiting for
start of H
shift Blinking
(2HZ)
while
waiting for
start of H
shift Off Off No
operation0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Closed Open Closed 2H to 4H
while
driving
During
operation
(Axle) Blinking
(2HZ) at
end of H
shift Off at end
of H shiftOff Off No
operation0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Closed Open Closed Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation1,0,1,0 Open Open Closed -----
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----


Completion of transfer case H-L area and axle shift timing may cause some variation in 2Hz blinking pattern.

TRANSFER CONTROL SYSTEM 7D1-17
Skip operation limitations (4L




2H) (Vehicle speed, engine speed, and transmission position not
specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4L Off On Off Off Open 1,1,0,1 Closed Open Closed -----
4L start of
operation Off On Off Off 2H
position
for 0.1
second 1,1,0,1 Closed Open Closed -----
10
second
display
during
limitation Blinking
(4HZ) Off Off Off Open 1,1,0,1 Closed Open Closed No
operation
during
limitation
Go to 4L
after 10
seconds
Off ON Off Off Open 1,1,0,1 Closed Open Closed -----

Skip operation limitations (2H




4L) (Vehicle speed, engine speed, and transmission position not
specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
2HL Off Off Off Off Open 1,0,1,0 Open Open Open -----
4L start of
operation Off Off Off Off 2H
position
for 0.1
second 1,0,1,0 Open Open Open -----
10
second
display
during
limitation Blinking
(4HZ) Blinking
(4HZ) Off Off Open 1,0,1,0 Open Open Open No
operation
during
limitation
Go to 2H
after 10
seconds
Off Off Off Off Open 1,0,1,0 Open Open Open -----


Under some conditions, a secondary operational indication may be received when the 4Hz operational
indication is present.