clutch thickness ISUZU TF SERIES 2004 Owner's Manual

7A4-34 UNIT REPAIR (JR405E)

08R&H36

8. High clutch piston
9. Reverse clutch piston
Install the reverse and high clutch drum to the oil pump.

Force compressed air into the oil pump oil channels.

Remove the high clutch piston and the reverse clutch
piston.


09R&H37



12R&H39

10.Seal ring (high clutch)
Remove the 2 seal rings from the high clutch piston.

13R&H38

11.Seal ring (reverse clutch)
Remove the 2 seal rings from the reverse clutch piston.




Inspection
Drive plate

Measure the drive plate facing thickness at 3 points.

Calculate the average value.
If the average value is less than the specified limit, the
drive plate must be replaced.
Drive plate facing thickness:
Standard – 2.0 mm (0.079 in)
Limit – 1.8 mm (0.071 in)

7A4-38 UNIT REPAIR (JR405E)

21R&H21

10.Dish plate, drive plates, driven plates, and retaining
plate Install the reverse clutch dish plate (1) the 2 driven plates
(2), the 2 drive plates (3), and retaining plate (4).

248L300003

11.Snap ring
Install the snap ring.

NOTE:
If is careful in the attachment direction of dish plate (1).

22R&H35



Install the reverse and high clutch drum to the oil pump
assembly.

Force compressed air (392 kPa/4.0 kg/cm
2) through the
oil pump oil passages to check high clutch operation.
If the clutch does not operate, the seal ring may be
damaged or the parts may have been installed in the
wrong order.


23CLEAR02



Measure the clearance between the high clutch retaining
plate and the snap ring.
If the clearance is outside the specified range, replace
the existing retaining plate with a new plate of the prope
r
size (thickness).
High clutch retaining plate and snap ring clearance
(A): 1.2~1.6 mm (0.047~0.063 in)
Available high clutch retaining plate thicknesses
4.6 mm (0.181 in)
4.8 mm (0.189 in)

7A4-40 UNIT REPAIR (JR405E)

25CLEAR04



Measure the clearance between the reverse clutch
retaining plate and the snap ring.
If the clearance is outside the specified range, replace
the existing retaining plate with a new plate of the prope
r
size (thickness).
Reverse clutch retaining plate and snap ring
clearance (B):
0.6~0.9 mm (0.024~0.035 in)
Available reverse clutch retaining plate thicknesses
4.8 mm (0.189 in)
5.0 mm (0.197 in)
5.2 mm (0.205 in)
5.4 mm (0.213 in)

7A4-46 UNIT REPAIR (JR405E)

18C&L-SUB28

19.Low one-way clutch
Remove the low one-way clutch.

19C&L-SUB29

20.Snap ring
Remove the snap ring from the low clutch drum.

20C&L-SUB31

21.Bearing
Remove the bearing.



Inspection
Drive plate

Measure the drive plate facing thickness at 3 points.

Calculate the average value.
If the average value is less than the specified limit, the
drive plate must be replaced.
Drive plate facing thickness:
Standard – 2.0 mm (0.079 in)
Limit – 1.8 mm (0.071 in)
Return spring

Check the number of effective return spring coils.
If the number is less than the specified minimum, the
return spring must be replaced.
Effective return spring coils (standard): 9.9

Measure the return spring outside diameter, free length,
and linear diameter.
If any of the measured values exceed the specified limit,
the return spring must be replaced.
Return spring measurements (standard):
Outside diameter – 9.7 mm (0.382 in)

7A4-50 UNIT REPAIR (JR405E)

34C&L-SUB15

10.Dish plate, drive plate, driven plate, and retaining plate
Install the low clutch dish plate (1), the 2 mm thick driven
plate (2), the 7 drive plate (3), the other 6 driven plates (4),
and the retaining plate (5).
NOTE:
Dish plate side with the identification mark must face the
driven plate.

248L300006

11.Snap ring
Install the snap ring to the low clutch drum.

NOTE:
It is careful in the attachment direction of dish plate.

35C&L-SUB38



36CLEAR06


Inspection

Insert the low one-way clutch inner race to the low clutch
drum.

Force compressed air (392 kPa/4.0 kg/cm
2) through the
oil passages of the low one-way clutch inner race to
check low clutch operation.
If the low clutch does not operate, the seal rings may be
damaged or the parts may have been installed in the
wrong order.

Measure the clearance between the low clutch retaining
plate and the snap ring.
If the clearance is outside the specified range, replace
the existing plate with a new plate of the proper size
(thickness).
Low clutch retaining plate and snap ring clearance:
0.9~1.3 mm (0.035~0.051 in)
Available low clutch retaining plate thicknesses
3.8 mm (0.150 in)
4.0 mm (0.157 in)

7A4-84 UNIT REPAIR (JR405E)

SERVICE STANDARD
Name BESCO ATF II or ATF III ATF
Quantity L 9.2 – 9.6
Seal ring clearance mm (in) 0.10 – 0.25 (0.0039 – 0.0098)
Housing and inner rotor side clearance mm (in) 0.02 – 0.04 (0.0008 – 0.0016)
Oil pump
Outer rotor and crescent clearance mm (in) 0.02 – 0.15 (0.0008 – 0.0059)
Number of drive plate / driven plate 7/7
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.9 – 1.3 (0.035 – 0.051)
3.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
Available low clutch retaining plate thickness mm (in)
4.8 (0.189)
Number of coil 9.9
Outside diameter mm (in) 9.7 (0.382)
Free length mm (in) 36.4 (1.433)
Low clutch
Return spring
Linear diameter mm (in) 1.2 (0.047)
Number of drive plate / driven plate 5/5
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 1.2 – 1.6 (0.047 – 0.063)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
Available high clutch retaining plate thickness mm (in)
5.4 (0.213)
Number of coil 10.2
Outside diameter mm (in) 8.0 (0.315)
Free length mm (in) 27.1 (1.067)
High clutch
Return spring
Linear diameter mm (in) 1.1 (0.043)
Number of drive plate / driven plate 2/2
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.6 – 0.9 (0.0236 – 0.035)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)
Reverse clutch
Available reverse clutch retaining plate thickness mm (in)
5.4 (0.213)
Low one-way
clutch Seal ring clearance mm (in) 0.10 – 0.25 (0.0039 – 0.0098)
Number of drive plate / driven plate 6/6
Standard mm (in) 2.0 (0.079)Drive plate facing thickness
Limit mm (in) 1.8 (0.071)
Retaining plate and snap ring clearance mm (in) 0.7 – 1.1 (0.028 – 0.043)
5.2 (0.205)
5.4 (0.213)
5.6 (0.220)
5.8 (0.228)
Low & reverse
brake
Available low & reverse brake retaining plate
thickness mm (in)
6.0 (0.236)