warning light ISUZU TF SERIES 2004 Service Manual

TRANSFER CONTROL SYSTEM 7D1-15
Transfer-related indicator lamp and switch function
Skip operation
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detectio
n (limit)
switches
LS1,
LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummy Remarks
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----
4L start of
operation Off Off Off Off 4L
position
for 0.1
second 1,0,1,0 Open Open Open Switch
operation
sensor
Start of
operation Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
while
driving
During
operation
(Synchro) Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
using
synchro
and retrial
During
operation
(Passing
through
4H) Off Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
During
operation
(Passing
through
4H) Off Blinking
(2HZ) Off Off No
operation0,0,1,1
0,1,0,1 Closed Open Open -----
During
operation
(N)
On Blinking
(2HZ) Off Off No
operation
0,0,1,1
0,1,0,1 Closed Open Closed -----
During
operation
(N) On Blinking
(2HZ) Off Off No
operation0,1,0,0 Closed Open Closed Switch
operation
sensor
During
operation
(N) On Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Closed 4H to 4L
while
driving
During
operation
(Axle
drive) Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
Axle
waiting Blinking
(2HZ) Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Open Open -----
4L waiting On Blinking
(2HZ) Off Off No
operation1,1,0,1 Closed Closed Closed 4H to 4L
while
waiting
4L On On Off Off No
operation1,1,0,1 Closed Open Closed -----

TRANSFER CONTROL SYSTEM 7D1-17
Skip operation limitations (4L




2H) (Vehicle speed, engine speed, and transmission position not
specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4L Off On Off Off Open 1,1,0,1 Closed Open Closed -----
4L start of
operation Off On Off Off 2H
position
for 0.1
second 1,1,0,1 Closed Open Closed -----
10
second
display
during
limitation Blinking
(4HZ) Off Off Off Open 1,1,0,1 Closed Open Closed No
operation
during
limitation
Go to 4L
after 10
seconds
Off ON Off Off Open 1,1,0,1 Closed Open Closed -----

Skip operation limitations (2H




4L) (Vehicle speed, engine speed, and transmission position not
specified)

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
2HL Off Off Off Off Open 1,0,1,0 Open Open Open -----
4L start of
operation Off Off Off Off 2H
position
for 0.1
second 1,0,1,0 Open Open Open -----
10
second
display
during
limitation Blinking
(4HZ) Blinking
(4HZ) Off Off Open 1,0,1,0 Open Open Open No
operation
during
limitation
Go to 2H
after 10
seconds
Off Off Off Off Open 1,0,1,0 Open Open Open -----


Under some conditions, a secondary operational indication may be received when the 4Hz operational
indication is present.

7D1-18 TRANSFER CONTROL SYSTEM
Transfer-related indicator lamp and switch function
2H
Neutral
2H
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detectio
n (limit)
switches
LS1,
LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummy Remarks
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----
Neutral
start of
operation Off Off Off Off Neutral
position
for 10
seconds1,0,1,0 Open Open Open Switch
operation
sensor
Start of
operation Off Off Blinking
(2HZ) Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
while
driving
During
operation
(Synchro) Off Off Blinking
(2HZ) Off No
operation1,1,1,0
0,0,1,0
0,1,1,0
0,1,1,1 Open Open Open 2H to 4H
using
synchro
and retrial
During
operation
(Passing
through
4H) Off Off Blinking
(2HZ) Off No
operation0,0,1,1 Closed Open Closed -----
During
operation
(Passing
through
4H) Off Off Blinking
(2HZ) Off No
operation0,0,0,1
0,1,0,1 Closed Open Closed 4H to 4L
while
driving
During
operation
(N)
Off Off Blinking
(2HZ) Off No
operation
0,0,0,1
0,1,0,1 Closed Closed Closed
4H to 4L
through
neutral
During
operation
(N) Off Off Blinking
(2HZ) Off No
operation0,1,0,0 Closed Closed Closed Switch
operation
sensor
Neutral Off Off On Off No
operation0,1,0,0 Closed Closed Open -----
2H start of
operation Off Off On Off 2H
position
for 10
seconds0,1,0,0 Closed Open Closed Switch
operation
sensor
During
operation
(Passing
through
N) Off Blinking
(2HZ) Off Off No
operation0,1,0,0 Closed Closed Closed 4L to 4H
through
neutral
During
operation Off Blinking
(2HZ) Off Off No
operation0,1,0,1
0,0,0,1 Closed Closed Closed 4L to 4H
while
driving

TRANSFER CONTROL SYSTEM 7D1-19
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detectio
n (limit)
switches
LS1,
LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummy Remarks
During
operation
(4H
waiting) Off Blinking
(2HZ) Off Off No
operation0,0,1,1 Closed Closed Closed 4L to 4H
while
waiting
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Closed Open Closed 2H to 4H
while
driving
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Open Open Closed Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation1,0,1,0 Open Open Closed -----
2H Off Off Off Off No
operation1,0,1,0 Open Open Open -----


Operational restrictions (vehicle speed, engine speed, and transmission position) are applicable to transfer
shifts in both directions (H
Neutral
L).

7D1-20 TRANSFER CONTROL SYSTEM
4H




Neutral




4H
Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4H On Off Off Off No
operation0,0,1,1 Closed Open Closed -----
Neutral
start of
operation On On Off Off Neutral
position
for 10
seconds 1,1,0,1 Closed Open Closed -----
Start of
operation Off Off Blinking
(2HZ) Off No
operation1,1,0,0 Closed Open Closed 4L to N
while
driving
During
operation
(N) Off Off Blinking
(2HZ) Off No
operation1,1,0,0 Closed Closed Closed 4L to N
with axle
driving
During
operation
(N) Off Off Blinking
(2HZ) Off No
operation0,1,0,0 Closed Closed Closed 4L to 4N
with axle
removed
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation0,1,1,1
0,1,1,0
0,0,1,0
1,1,1,0 Open Open Closed Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation1,0,1,0 Open Open Closed -----
Neutral Off Off On Off No
operation0,1,0,0 Closed Closed Open -----
4H start
of
operation Off Off Off Off 2H
position
for 10
seconds 0,1,0,0 Open Open Open Switch
operation
sensor
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation1,1,0,0 Closed Closed Open 4L to 4H
through
neutral
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation0,1,0,0 Closed Closed Open 4L to 4H
through
neutral
During
operation Off Blinking
(2HZ) Off Off No
operation0,1,0,1
0,0,0,1 Closed Closed Open 4L to 4H
while
driving
4H
waiting Blinking
(2HZ) Off) Off Off No
operation0,0,1,1 Closed Closed Open 4L to 4H
while
waiting
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation0,0,1,1 Closed Open Open Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation0,0,1,1 Closed Open Open -----
4H On Off Off Off No
operation0,0,1,1 Closed Open Closed -----

7D1-22 TRANSFER CONTROL SYSTEM
4L




Neutral




4L

Item 4WD
lamp 4L lampNeutral
lamp Check
4WD
warning
light 4WD
switch Actuator
detection
(limit)
switches
LS1, LS2,
LS3. and
LS4
1 = on
2 = off Transfer
4WD
switch Transfer
neutral
switch SOF
actuator
switch
Or
Axle
dummyRemarks
4L On On Off Off No
operation1,1,0,1 Closed Open Closed -----
Neutral
start of
operation On On Off Off Neutral
position
for 10
seconds 1,1,0,1 Closed Open Closed -----
Start of
operation Off Off Blinking
(2HZ) Off No
operation1,1,0,0 Closed Open Closed 4L to N
while
driving
During
operation
(N) Off Off Blinking
(2HZ) Off No
operation1,1,0,0 Closed Closed Closed 4L to N
with axle
driving
During
operation
(N) Off Off Blinking
(2HZ) Off No
operation0,1,0,0 Closed Closed Closed 4L to 4N
with axle
removed
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation0,1,0,0 Closed Closed Closed Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation0,1,0,0 Closed Closed Closed -----
Neutral Off Off On Off No
operation0,1,0,0 Closed Closed Open -----
4L start of
operation Off Off On Off 4L
position
for 10
seconds 0,1,0,0 Open Open Open Switch
operation
sensor
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation1,1,0,0 Closed Closed Open 4H to 4L
through
neutral
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation1,1,0,0 Closed Closed Open 4H to 4L
through
neutral
During
operation
(N) Off Blinking
(2HZ) Off Off No
operation1,1,0,0 Closed Closed Open 4H to 4L
through
neutral
4H
waiting On Blinking
(2HZ) Off Off No
operation1,1,0,1 Closed Closed Open 4L while
waiting
During
operation
(Axle) Blinking
(2HZ) Off Off Off No
operation1,1,0,1 Closed Open Open Axle
driving
Axle
waiting
Blinking
(2HZ) Off Off Off No
operation1,1,0,1 Closed Open Open -----
4H On On Off Off No
operation1,1,0,1 Closed Open Closed -----

Operational restrictions (vehicle speed, engine speed, and transmission position) are applicable to transfer
shifts in both directions (H
Neutral
L).

7A2-12 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Functions of Input / Output Components
Component Function
Transfer low signal Detects the transfer High/Low position.
OD Cancel signal Detects whether the cruise control unit is judged OD cancel mode.
Output revolution sensor
(Transmission) Detects the vehicle speed.
Input revolution sensor
(Transmission) Detects the input revolution (OD direct clutch drum revolution).
Engine revolution sensor Detects the engine revolution with CAN.
Throttle position signal Detects the throttle opening rate with CAN.
Neutral start switch Detects the select lever position.
Pattern select switch Detects whether the driver has selected "NORMAL" or "POWER" mode.
Brake lamp switch Detects whether the driver has pressed the brake pedal or not.
Oil temperature sensor Detects the oil temperature.




I
n
p
u t
Diagnostic start switch Starts self-diagnosis and displays a code for faulty part if any.
I
n
p
u t
/
O
u t
p
u t Data link connector When connected with Tech2 or tester, can communicate the data for function
check, etc.
Shift solenoid S1, S2 Selects shift point and gear position suited to the vehicle running condition on the
basis of TCM output.
Lock-up control solenoid SL Control the lock-up clutch suited to the vehicle running condition on the basis of TCM output.
Pressure control solenoid
STH Adjusts throttle pressure by energizing current of linear pressure control solenoid
to prevent the shift shock and to obtain shift smoothly.
"CHECK TRANS" lamp When trouble has occurred to throttle position sensor, vehicle speed sensor, or
solenoid, "CHECK TRANS" lamp is blinked to warn the driver. If also displays the
trouble code.
A/T OIL TEMP warning
lamp Lights when ATF oil temperature rises. (Turned on at greater than 146


C
(295

F). Turned off at less than 132

C (270

F).
POWER lamp Lights when POWER MODE detected.



O
u
t
p
u
t
3rd Start lamp Lights when 3rd Start MODE detected.
C
o
m
p
u t
e r Transmission Control
Module (TCM) Based on the signal from each switch and sensors, judges necessary shift point
and lock-up operation, and send signal to each solenoid.

CONSTRUCTION AND FUNCTION 7A1-17

ATF Thermo Sensor

The ATF thermo sensor detects the ATF temperature in the oil pan and sends signal to the TCM.

The ATF thermo sensor is of the thermister type that the resistance value changes according to the ATF
oil temperature.

The lower is the ATF temperature, the larger is the resistance, and vice versa.

When the ATF temperature exceeds 145C, the TCM lights up the ATF temperature warning lamp in the
meter. When the ATF temperature decreases below 128C, the ATF temperature warning lamp goes out.

The ATF thermo sensor is installed to the lower control valve body and integrated with the harness
assembly.













10.0 100.0 1,000.0 10,000.0 100,000.0
-30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
A TF Temperature (°C)
Resistance (

)

Figure 29. Characteristic of Thermo Sensor


Figure 30. Location of Thermo Sensor
ATF Temperature
(deg. C) Resistance (Ohm)
(Approximately) ATF Temperature
(deg. C) Resistance (Ohm)
(Approximately)
-30 29,614 100 190
-20 16,705 110 149
-10 9,842 120 118
0 6,028 128 98
20 2,500 130 94
40 1,160 135 84
50 819 140 76
60 591 145 68
80 324 150 62

DIAGNOSIS (JR405E) 7A2-5
PAGE
NO. Z3: MODE LAMP (POWER DRIVE OR 3RD START) LIGHTS UP WHEN
THE POWER MODE OR 3RD START MODE IS TURNED OFF .................................. 7A2-137
NO. Z4: OIL TEMPERATURE WARNING LAMP LIGHTS UP ...................................... 7A2-137
NO. Z5: SELECT LEVER FEELING IS FAULTY. .......................................................... 7A2-137
NO. Z6: POOR FUEL CONSUMPTION ......................................................................... 7A2-138
NO. Z7: PATTERN SELECT SWITCH IS FAULTY........................................................ 7A2-138
NO. Z8: OIL IS SPLASHED DURING THE RUNNING .................................................. 7A2-138
NO. Z9: ABNORMAL SMELL ........................................................................................ 7A2-138
NO. Z10: ATF QUANTITY IS LOW OR HIGH ................................................................ 7A2-138
NO. Z11: ABNORMAL OIL PRESSURE........................................................................ 7A2-139
NO. Z12: REVERSE BUZZER DOES NOT RING .......................................................... 7A2-139
STALL TEST .................................................................................................................. 7A2-140
LINE PRESSURE TEST................................................................................................. 7A2-141
TIME LAG TEST............................................................................................................. 7A2-143
TEST DRIVE................................................................................................................... 7A2-144
SHIFT POINT CHART .................................................................................................... 7A2-147
SHIFT POINT DIAGRAM................................................................................................ 7A2-149
TCM VOLTAGE CHECK ................................................................................................ 7A2-154

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.