brake ISUZU TF SERIES 2004 Repair Manual

5A-34 BRAKE CONTROL SYSTEM

4. Notes
 If the following should occur during Diagnostic
Trouble Code (DTC) display, the display will be
discontinued. After initial check, the status that
is under the control of ABS will be returned :
– The vehicle starts (The wheels turn) or the
brake pedal is depressed.
 Up to 3 different codes can be stored.
 If the ABS should turn OFF due to an
intermittent defect, the system will be restored
at the next key cycle, if the initial check finds no
abnormality (when IGN is switched from OFF to
ON).
5. An example of DTC display
Display of DTC 23

B05R100001
After displaying DTC 12 three times, one DTC after
another is displayed. DTC is displayed on small
order.

C05L300017
The DTC 12 is displayed repeatedly.

BRAKE CONTROL SYSTEM 5A-35

Basic Diagnostic Flow Chart

RTW45AMF000101

Step Action Value(s) Yes No
1 1. Ignition “ON,”engine “OFF.”
2. Observe the ABS warning lamp.
Note: If a starter switch is turned ON, ABS warning
lamp will turn on and a ABS warning lamp will be
turned off after 3 seconds.
Is the ABS warning lamp “ON”?
- Go to Step 2 Go to “No
ABS warning
lamp”
2 1. Ignition “OFF.”
2. Install Tech2.
3. Ignition “ON.”
4. Attempt to display ABS data with the Tech 2.
Does the Tech 2 display ABS data?
- Go to Step 5 Go to Step 3
3 1. Ignition “OFF,” disconnect the EHCU.
2. Check the DLC (Data Link Connector) circuit for an
open, short to ground, or short to voltage.
Also, check the DLC ignition feed circuit for an
open or short to ground and the DLC ground circuit
for an open.
3. If a problem is found, repair as necessary.
Was a problem found?
- Go to Step 2 Go to Step 4

5A-36 BRAKE CONTROL SYSTEM

Step Action Value(s) Yes No
4 1. Check the EHCU circuit for an open, short to
ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open.
2. If a problem is found, repair as necessary.
Was a problem found?
- Go to Step 2 Go to Step 11
5 Select “Display DTCs” with the Tech 2.
Are any DTCs stored? - Go to Step 6 Go to Step 10
6 Review and record for Tech 2 Failure Records data
and DTCs.
Is the action complete? - Go to Step 7 -
7 Following the DTC is stored.
Is this DTC C0271 stored?
- Go to
applicable
DTC table
after Go to
step 8 Go to Step 8
8 Clear the DTCs by “Clear the Information“ with Tech
2.
Did the DTCs cleared? - Go to Step 9 -
9 Select “Display DTCs” with the Tech 2.
Are any DTCs stored?
- Go to
applicable
DTC table Go to Step 10
10 Review and record for Tech 2 data.
Is the action complete?
- Go to
Symptom
Diagnosis and
Go to Basic
Inspection
Procedure -
11 Replace the EHCU.
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification; 2WD Model or 4WD Model)
Is the action complete? - Verify repair -

BRAKE CONTROL SYSTEM 5A-37

Basic Inspection Procedure
1. Basic Inspection of Service Brake
Step Action
Value(s) Yes No
1 Is the fluid level normal?
- Go to Step 2 Replenish with
fluid
Go to Step 2
2 Does fluid leak?
- Repair
Go to Step 3 Go to Step 3
3 Is the booster function normal?
- Go to Step 4 Repair
Go to Step 4
4 Is the pad and rotor normal?
- Go to Step 5 Repair
Go to Step 5
5 Reconnect all components. Ensure all component
are properly mounted.
Was this step finished? - Finished Go to Step 5

2. Ground Inspection
Step Action
Value(s) Yes No
1 Does ABS related ground points normally?
- Go to Step 2 Repair
Go to Step 2
2 Reconnect all components. Ensure all component
are properly mounted.
Was this step finished? - Finished Go to Step 2

5A-38 BRAKE CONTROL SYSTEM

Wheel Speed Sensor Inspection Procedure
Procedure
1.Ignition "OFF".
2.Disconnect the each wheel speed sensors.
3.Check the voltage at sensor harness connector.
Note : Voltage measurement is performed in the phase
where the wheel speed sensor is installed in vehicles.

C05L300019
Connector Pin-outs

Front Wheel Speed Sensor
1 (+) (+12V)
2 (-) (signal)

Rear Wheel Speed Sensor
1 LH (+) (+12V)
2 LH (-) (signal)
3 RH (+)(+12V)
4 RH (-) (signal)






Output Value
High State 1.28~2.2V
Low State 0.5~0.86V
High-Low
Difference more than 0.8V

BRAKE CONTROL SYSTEM 5A-39

Symptom Diagnosis
The symptoms that cannot be indicated by warning
lamp can be divided in the following five categories:
1. ABS works frequently but vehicle does not
decelerate.
2. Uneven braking occurs while ABS works.
3. The wheels are locked.

4. Brake pedal feel is abnormal.
5. Braking sound (from EHCU) is heard while not
braking.
6. No ABS warning lamp
These are all attributable to problems which cannot be
detected by EHCU self-diagnosis. Use the customer
complaint and a test to determine which symptom is
present.
ABS Works Frequently But Vehicle Does Not Decelerate

Step Action
Value(s) Yes No
1 Is braking force distribution normal between front
and rear of vehicle?
- Go to Step 2 Repair brake
parts.
Go to Step 7
2 Are axle parts installed normally?
- Go to Step 3 Repair axle
parts.
Go to Step 7
3 Is there play in each or any wheel speed sensor?
- Repair wheel
speed sensor.
Go to Step 7 Go to Step 4
4 Is there damage, or powered iron sticking to each or
any wheel speed sensor/sensor rotor?
- Replace
wheel speed
sensor or
sensor rotor.
Go to Step 8 Go to Step 5
5 Is the each wheel speed sensor output normal?
- Go to Step 6 Replace
wheel speed
sensor or
repair
harness.
Go to Step 7
6 Is the 4WD control system function normal?
- 2-4WD Repair
or Go to Step
7 Repair or
replace 2-
4WD control
System.
Go to Step 7
7 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 7

5A-40 BRAKE CONTROL SYSTEM

Uneven Braking Occurs While ABS Works

Step Action
Value(s) Yes No
1 Is there play in each or any sensor?
- Repair.
Go to Step 5 Go to Step 2
2 Damage or powdered iron sticking to each or any
sensor/sensor rotor?
- Repair.
Go to Step 5 Go to Step 3
3 Is the each sensor output normal?
- Go to Step 4 Replace
sensor or
repair
harness.
Go to Step 5
4 Is brake pipe connecting order correct?
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification; 2WD Model or 4WD Model) - Replace
EHCU.
Go to Step 5 Reconnect
brake pipe
correctly.
Go to Step 5
5 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 5

The Wheels Are Locked

Step Action Value(s) Yes No
1 Is ABS working?
- Go to Step 2 Go to Step 4
2 Is vehicle speed under 5 km/h?
- Go to Step 3 Normal.
3 Is the each sensor output normal?
- Go to Step 4 Replace
sensor or
repair
harness.
Go to Step 6
4 Is 2-4WD system function normal?
- Go to Step 5 Replace 2-
4WD controll
unit or repair
harness.
Go to Step 6
5 Is EHCU grounded properly?
Note: Check the EHCU type for specification, when
the EHCU is replaced.
(Specification; 2WD Model or 4WD Model) - Replace
EHCU.
Go to Step 6 Repair.
Go to Step 6
6 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 6

BRAKE CONTROL SYSTEM 5A-41

Brake Pedal Feed Is Abnormal

Step Action
Value(s) Yes No
1 Is the stop light actuated when the brake pedal is
depressed?
- Go to Step 2 Go to Step 3
2 1. Turn the ignition switch off.
2. Disconnected EHCU connector.
Is the check voltage for EHCU connector terminals
when brake pedal is depressed than battery voltage?
- Go to Step 4 Harness NG
between stop
light SW and
EHCU.
Go to Step 6
3 Is stop light fuse normal?
- Go to Step 5 Replace stop
light fuse.
Go to Step 6
4 Is the check continuity between EHCU connector to
body grounded?
- Go to Step 6 Repair body
grounded
harness.
Go to Step 6
5 Is stop light switch operation normal?
- Repair stop
light harness.
Go to Step 6 Replace stop
light switch.
Go to Step 6
6 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 6

5A-42 BRAKE CONTROL SYSTEM

Braking Sound (From EHCU) Is Heard While Not Braking

Step Action Value(s) Yes No
1 Is this the first vehicle start after engine start?
- It is self
checking
sound
Normal. Go to Step 2
2 Is vehicle speed under 10 km/h?
- It is self
checking
sound
Normal. Go to Step 3
3 Check for the following condition:
 At the time of shift down or clutch operation.
 At the time of low road friction drive (ice or snow
road) or rough road drive.
 At the time of high-speed turn.
 At the time of passing curb.
 At the time of operating electrical equipment
switches.
 At the time of racing the engine.
Did it occur under any one condition above?
- ABS may
sometimes be
actuated even
when brake
pedal is not
applied. Go to Step 4
4 Is there play in each or any sensor/wheel speed
sensor rotor?
- Repair.
Go to Step 7 Go to Step 5
5 Damage or powdered iron sticking to each or any
sensor/wheel speed sensor rotor?
- Repair.
Go to Step 7 Go to Step 6
6 Is each sensor normal?
Note : Check the EHCU type for specification, the
EHCU is replaced.
(Specification; 2WD or 4WD Model)

- Check
harness/
connector for
suspected
disconnection
If no
disconnection
is found,
replace EHCU
Go to Step 7 Repair.
Go to Step 7
7 Reconnect all components, ensure all components
are properly mounted.
Was this step finished?
- Repeat the
“Basic
diagnostic
flow chart” Go to Step 7

BRAKE CONTROL SYSTEM 5A-43

No ABS Warning Lamp

Step Action
Value(s) Yes No
1 Check the meter fuse for the instrument cluster
ignition feed circuit.
Is the fuse OK? - Go to Step 3 Go to Step 2
2 Replace the fuse.
Is the action complete? - Verify repair
Go to Step 3 -
3 1. Ignition “OFF,” disconnect the EHCU.
2. Ignition “ON,”engine “OFF.”
3. Observe the ABS warning lamp.
Is the ABS warning lamp “ON”?
- Go to Step 5 Go to Step 4
4 Repair or replace the meter circuit or meter.
Is the action complete? - Verify repair -
5 1. Check the EHCU circuit for an open, short to
ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open.
2. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 6
6 1. Ignition “OFF,” reconnect the EHCU.
2. Ignition “ON,”engine “OFF.”
3. Observe the ABS warning lamp.
Is the ABS warning lamp “ON”?
- Verify repair Go to Step 7
7 Replace EHCU.
Note : Check the EHCU type for specification, the
EHCU is replaced.
(Specification; 2WD or 4WD Model)
Is the action complete? - Verify repair -