propeller shaft ISUZU TF SERIES 2004 Repair Manual

7D-6 TRANSFER CASE

Transfer Case Assembly
Transfer Case Assembly and Associated Parts



RTW47DLF000501
Legend


(1) Rear Propeller Shaft
(4)
Center Exhaust Pipe (6VE1 only)
(2) Front Propeller Shaft

(3) Transfer Case Assembly

TRANSFER CASE 7D-7

Removal
NOTE: Before removing transmission and transfer
assembly from vehicle, change the transfer mode to
2WD using the 4WD push button switch on dash panel.
1.
Disconnect battery ground cable.
2.
Raise and support vehicle with suitable stands. Drain
transfer case fluid.
3. Remove the center exhaust pipe(5). (6VE1 only)
4.
Remove rear propeller shaft (1) and front propelle
r
shaft (2)(3).
NOTE: Apply alignment marks on the flange at both
front and rear sides.
5.
Disconnect harness connectors and clip.

Connector: transfer switch, 2WD-4WD actuator,
speed sensor.
NOTE: Avoid turning the vehicle ignition switch to the
ON position when the 2WD-4WD connector is removed
(battery connected).
If the ignition switch must be turned to the ON position,
the controller must first be removed (memory must be
cleared because the CHECK 4WD INDICATOR will
light).
6.
Remove transfer case (4) from the vehicle.
Installation
1.
Apply a thin coat of molybdenum disulfide grease to
the input shaft spline as shown in the figure.

260R300001

TRANSFER CASE 7D-9

For A/T
261R300002

3.
Connect harness connectors and clip.

Connector: transfer switch, 2WD-4WD actuator,
speed sensor.
4. Install center exhaust pipe(5). (6VE1 only)
5.
Install rear propeller shaft (1) and front propelle
r
shaft (2)(3).
Torque: 63 N




m (6.4 kg




m/46 lb ft)

7D1-4 TRANSFER CONTROL SYSTEM
Summary of transfer control system
The transfer control system switches between the 2-wheel
drive (2H), 4-wheel drive high-speed (4H), 4-wheel drive low-
speed (4L), and neutral positions electrically when the driver
operate the switches.
This system has following functions.
1. Connection or disconnection of drive force distribution to
the front wheel front shaft (axle shaft) (The drive force
distribution to the front propeller is connected o
r
disconnected with the motor actuator.)
2. Try to repeat the connection or disconnection of the front
wheel drive function as described above.
3. Option: Shift on the fly type only.
Instruction of connection or disconnection of the drive force
transmission between the front wheel axle (axle shaft) and
front wheel
(The motor actuator connects or disconnects the left front
wheel ad front wheel axle (axle shaft).).
4. Shifting of auxiliary transmission gears, connection o
r
disconnection of wheel and engine drive force (4H, 4L,
neutral).
5. Operation of indicator on the instrument panel.
6. Transmission of position signal to other controllers.

7A3-16 ON-VEHICLE SERVICE (AW30 –40LE)

Evaluation
i. If there is no 1 
2 upshift:

Solenoid S2 is stuck
 1 –2 shift valve is stuck
ii. If there is no 2 
3 upshift:

Solenoid S1 is stuck
 2 –3 shift valve is stuck
iii. If there is no 3 
OD upshift (throttle valve opening
1/2):

Solenoid S2 is stuck
 3 –OD shift valve is stuck
iv. If the shift point is defective: Refer to TROUBLESHOOTING CHART in this
section.
v. If the lock-up is defective: Refer to TROUBLESHOOTING CHART in this
section.
2. In the same manner, check the shock and slip at the 1 
2, 2 
3 and 3 
OD upshifts.
NOTE: Drive the vehicle on level ground.
Evaluation
If the shock is excessive:
Refer to TROUBLESHOOTING CHART in this section.
3. Run at “D" range lock-up or OD gear and check fo
r
abnormal noise and vibration.
NOTE: The check for the cause of abnormal noise and
vibration must be made with extreme care as it could
also be due to loss of balance in the propeller shaft,
differential, the torque converter, etc. or insufficient
bending, rigidity, etc. in the power train.



RUW37ASH000201

4. While running in “D" range, 2nd, 3rd gears and OD,
check to see that the possible kick-down vehicle
speed limits for 2 1, 3 1, 3 2, OD 3 and
OD 
2 kick-downs conform to those indicated on
the automatic shift diagram.



RUW37AMH000101
5. Check for abnormal shock and slip at kick-down.
6. While running in “D" range, OD gear or “lock-up",
shift to “2" and “L" ranges and check the engine
braking effect at each of these ranges.
7. Also check to see that downshift is made from 3 
2
or from OD to 3 and then to 2 immediately and that
2 
1 downshift point is within the limits shown in the
diagram when tested by releasing the accelerato
r
pedal and shifting into position of “L" while driving in
the third gear or in overdrive.

7A3-40 ON-VEHICLE SERVICE (AW30 –40LE)

Rear Oil Seal (Adapter Housing, 4
 
4)

Removal

1. Remove the front and rear propeller shaft assembly
from the transfer case.
2. Remove the transfer case assembly from the transmission case.
Refer to Section 4 DRIVELINE/AXLE.
3. Using a screwdriver, remove the rear oil seal.
Installation
1. Apply ATF to a new rear oil seal lip.
2. Using oil seal installer, install the rear oil seal to the adapter housing.
Oil seal installer : J –36797



RUW37ASH002401
3. Install the transfer case assembly.
Refer to section 4 DRIVE/AXLE.
4. Install the front and rear propeller shaft assembly.
Torque (Propeller shaft flange bolt) : 63 N 


m (46
Ib ft)

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-41

Rear Oil Seal (Extension Housing, 4
 
2)

Removal

1. Remove the rear propeller shaft assembly.
2. Using a screwdriver, remove the rear oil seal.
Installation
1. Apply ATF to a new rear oil seal lip.
2. Using oil seal installer, install the rear oil seal to the extension housing.
Oil seal installer : J –46197




249L100005
3. Install the rear propeller shaft.
Torque (Flange bolt) : 63 N 


m (46 Ib ft)

7A3-42 ON-VEHICLE SERVICE (AW30 –40LE)

Transmission Assembly
Transmission and Associated Parts




Legend
(9) Under Cover
(1) Rear Propeller Shaft (10) Flex Plate Torque Converter bolt
(2) Front Propeller Shaft (4WD only) (11) Shift Cable
(3) Middle Exhaust Pipe (12) Rear Mount Rubber
(4) Transfer Case Assembly (4WD only) (13) Heat Protector
(5) Fuel Pipe Clip and Bracket (14) Transmission Crossmember
(6) ATF Pipe and Clip (15) Transmission Assembly (2WD)
(7) Oil Level Gauge and Guide Tube (16) Transmission Assembly (4WD)
(8) Suspension Crossmember

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-43

Removal
NOTE: Before removing transmission and transfer
assembly from vehicle, change the transfer mode to
2WD using the 4WD push button switch on dash panel.
1. Disconnect battery ground cable.
2. Raise and support vehicle with suitable stands.
3. Remove front propeller shaft.(4WD only)
NOTE: Apply alignment marks on the flange at both
front and rear sides.
4. Remove rear propeller shaft.
NOTE: Apply alignment marks on the flange at the
differential side.


401RS023
5. Remove the middle exhaust pipe.



RTW37ASH0001

6. Disconnect the transfer harness connectors and the
clips.(4WD only)

Speed sensor
 2W-4W shift actuator
NOTE: Avoid turning the vehicle ignition switch to the
ON position when the 2WD-4WD connector is removed
(battery connected).
If the ignition switch must be turned to the ON position,
the controller must first be removed (memory must be
cleared because the CHECK 4WD INDICATOR will
light).
7. Support transfer case with a transmission jack.(4WD only)
8. Remove the transfer case assembly from the
transmission.(4WD only)
9. Disconnect the shift cable.
10. Remove the fuel pipe clips with the fuel pipes from the brackets and put aside it. Remove the fuel pipe
brakets from the transmission.






P1010010
11. Discinnect the transmission harness connectors
and clips.
12. Remove the oil level gauge and the guide tube.
13. Remove the suspension crossmember.

ON-VEHICLE SERVICE (AW30 –40LE) 7A3-49


Tighten transmission transfer bolts as shown in
the figure.(4WD only)

261R300002
20. Connect transfer harness connectors and
clips.(4WD only)

Speed sensor
 2W-4W shift actuator
21. Install the middle exhaust pipe.



RTW37ASH0001
22. Install the rear propeller shaft.
Torque: 63 N 


m (6.4 kg 


m/46 lb ft)
NOTE: Align alignment marks on the flange.
23. Install the center bearing on crossmember.
Torque: 69 N 


m (7.0 kg 


m/51 lb ft)


24.Install the front propeller shaft.(4WD only)
Torque: 63 N 


m (6.4 kg 


m/46 lb ft)
NOTE: Align alignment marks on the flange.


401RS023
25. Connect battery ground cable.