propeller shaft ISUZU TF SERIES 2004 Repair Manual

MSG MODEL 7B-13





Starter Motor
1. Install the starter motor to the engine rear plate.
2. Tighten the starter motor bolts to the specified torque.
Starter Motor Torque N

m (kgf

m/lb

ft)
78 (8.0 / 58)




Slave Cylinder
Install the slave cylinder to the transmission case.
Slave Cylinder Bolt Torque N

m (kgf

m/lb

ft
)
78 (8.0 / 58)

Harness Connector
Connect the back up light switch connector and speedometer
sensor connector.



Rear Propeller Shaft (Single Shaft Type)
1. Insert the splined yoke 1 with the propeller shaft into the
transmission main shaft spline
2 .
2. Install the propeller shaft flange yoke
3 to the drive pinion
side.
3. Tighten the propeller shaft flange yoke bolt to the specified
torque.
Propeller Shaft Flange Yoke Bolt Torque N
m (kgf
m/lb
ft)
M8 : 35.3 (3.6 / 26)
M10 : 62.7 (6.4 / 46.3)



Rear Propeller Shaft (Dual Shaft Type)
1. Place the center bearing and retainer 1 together with the
1st propeller shaft
2 and 2nd propeller shaft 7 on the No.4
crossmember
3.
2. Insert the splined yoke
4into the transmission main shaft
spline
5.
3. Tighten the center bearing retainer bolts
6 to the specified
torque.
Center Bearing Retainer Bolt Torque N

m (kgf

m/lb

ft)
60.8 (6.2 / 44.8)



4. Connect the 2nd propeller shaft
7 and drive pinion side 8.
Be sure to align the setting marks applied at disassembly.
5. Tighten the coupling bolts to the specified torque.
Propeller Shaft Flange Yoke Bolt
Torque N

m (kgf

m/lb

ft)
M8 : 35.3 (3.6 / 26)
M10 : 62.7 (6.4 / 46.3)

MANUAL TRANSMISSION 7B1-5

Rear Oil Seal (4





2)
Disassembled View
220R300030
Legend

(1) Rear Propeller Shaft (2) Rear Oil Seal

Removal
1. Raise and support vehicle with suitable jack stands.
2. Remove propeller shaft flange yoke bolts and nuts
at the differential side.
3. Remove center bearing from crossmenber.
4. Remove prepeller shaft from the transmission main
shaft spline.
Refre to the section “Rear Propeller Shaft”.
5. Use a screwdriver to pry the rear oil seal from the
rear cover.

Installation
1. Install a new oil seal (2) using the installer 5-8522-
0050-0.



220RS044
2. Insert the splined yoke into the transimission
mainshaft spline.
3. Install the propeller shaft flange yoke to the drive
pinion flange.

MANUAL TRANSMISSION 7B1-7

Transmission (4





2)
Disassembled View


RTW47BLF000701
Legend

(1) Gear Control Lever Knob (10) Slave Cylinder
(2) Rear Floor Console (bucket seat) (11) Nut : rear mount to Crossmember
(3) Front Floor Console (12) Transmission Crossmember
(4) Grommet Assembly (13) Nut : rear mount to transmission
(5) Gear Control Lever (14) Rear Mount Rubber
(6) Rear Propeller Shaft (15) Starter (Diesel engine only)
(7) Exhaust Pipe Nut (Diesel engine only) (16) Transmission Retaining Nut and Bolt
(8) Exhaust Pipe (6VE1 only) (17) Transmission Assembly
(9) Fuel Pipe Bracket

MANUAL TRANSMISSION 7B1-9

6. Remove gear control lever (5).
7. Raise and support vehicle with suitable stands.
8. Remove rear propeller shaft (6).
NOTE: Apply alignment marks on the flange at the
differential side.

401RS023
9. Loosen the front exhaust pipe fixing nuts (7) at the
engine side but not remove them. (Diesel engine
only)
150R300003

10. Remove the exhaust pipe (8). (6VE1 only)
RTW37ASH0001
11. Disconnect harness connectors and clips on the
transmission.

Neutral Switch


Back up Switch

Car Speed Sensor
12. Remove the fuel pipe bracket (9) with pipes from the
transmission (17).
Diesel engine
220R300012

Legend
(1) Bolt
(2) Nut
(3) Fuel Pipe Assembly

MANUAL TRANSMISSION 7B1-17

14. Install the exhaust pipe (8). (6VE1)
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
RTW37ASH000101
15. Install rear propeller shaft (6).
Torque: 63 N




m (6.4 kg




m/46 lb




ft)
16. Install center bearing on crossemember.
Torque: 69 N




m (7.0 kg




m/51 lb




ft)
17. Install gear control lever (5).
Torque: 19 N




m (1.9 kg




m/14 lb




ft)
18. Install grommet assembly (4).
Torque: Screw 1.4 N




m (0.14 kg




m/12 lb




in)
Nut 7 N




m (0.7 kg




m/61 lb




in)




RTW47BMH000101

Legend
(1) Grommet Assembly
(2) Floor Panel
(3) Front
19. Install front floor console (3) and rear floor console
(2).
20. Install gear control lever knob (1).
To the female thread portion, adhesive (TB1344 or
LOCTITE 222 or equiv.) of 3 - 4 drops to be applied
and transmission knob tightened.
Torque: 9 N




m (0.9 kg




m/78 lb




in)
After tightening to specified torque, knob
rewrenched until direction of shift pattern due
positioned.
21. Connect battery ground cable.

7B1-64 MANUAL TRANSMISSION

Transmission (4





4)
Disassembled View

RTW47BLF001001
Legend

(1) Gear Control Lever Knob (10) Transmission-Transfer Fixing Bolt
(2) Rear Floor Console (bucket) (11) Transfer Assembly
(3) Front Floor Console (12) Fuel Pipe Bracket
(4) Grommet Assembly (13) Slave Cylinder
(5) Gear Control Lever (14) Rear Mount Nut
(6) Rear Propeller Shaft (15) Transmission Crossmember
(7) Front Propeller Shaft (16) Starter (Diesel engine only)
(8) Exhaust Pipe Nut (Diesel engine) (17) Transmission Retaining Nut and Bolt
(9) Exhaust Pipe Assembly (6VE1) (18) Transmission Assembly

7B1-66 MANUAL TRANSMISSION

6. Remove gear control lever (5).
7. Raise and support vehicle with suitable stands.
8. Remove rear propeller shaft (6).
NOTE: Apply alignment marks on the flange at the
differential side.
9. Remove front propeller shaft (7).
NOTE: Apply alignment marks on the flange at both
front and rear sides.
401RS023
10. Loosen the front exhaust pipe fixing nuts (8) at the
engine side but not remove them. (Diesel engine
only)
150R300004
11. Remove the exhaust pipe (9). (6VE1 only)
RTW37ASH000101
12. Disconnect harness connectors and clips on the
transfer.


Actuator connector


Car Speed Sensor

810R300069

Legend
(1) Neutral Switch Connector: Transmission
(2) Back up Switch Connector
(3) Speed Sensor Connector
(4) Actuator Connector
(5) 2W - 4W Switch Connector
(6) Neutral Switch Connector: Transfer

7B1-74 MANUAL TRANSMISSION

15. Install the transmission-transfer bolts and nut and
tighten them to the specified torque.
Torque: 41 N





m (4.2 kg





m/30 lb





ft)
261R300005
18. Install the exhaust pipe (9). (6VE1)
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
RTW37ASH000101
19. Install front propeller shaft (7).
Refer to the section “Front Propeller Shaft”.
20. Install rear propeller shaft (6).
Torque: 63 N




m (6.4 kg




m/46 lb




ft)
21. Install the center bearing on crossmember.
Torque: 69 N




m (7.0 kg




m/51 lb




ft)
22. Install gear control lever (5).
Torque: 19 N





m (1.9 kg





m/14 lb





ft)

7D-4 TRANSFER CASE

Transfer Rear Oil Seal
Transfer Rear Oil Seal and Associated Parts
220R300018
Legend


(1) Rear Propeller Shaft

(2) Oil Seal


Removal
1.
Disconnect the rear propeller shaft (1) from the
transfer case side.
2.
Remove the oil seal from the transfer case.

Installation
1.
Install oil seal and apply engine oil to the oil seal
outer surfaces.
2.
Apply the recommended grease (BESCO L2) or
equivalent to the oil seal lip.
3.
Use the oil seal installer 5-8840-2786-0 to install the
rear seal (2) to the transfer rear case.

TRANSFER CASE 7D-5

220R300021
4.
Connect the rear propeller shaft.