stop start ISUZU TF SERIES 2004 Repair Manual

7D1-48 TRANSFER CONTROL SYSTEM
From 4H to 4L; Even after the correction step 3-3(*), 4Lo indicator blinks at 4Hz
Step Action Yes No
1 Is the ignition switch ON? Turn it OFF once. Go to step 2.
2 Turn ON the ignition switch and
check the valve. Do not start
the engine.
Has the valve check for 2
seconds been completed
normally? Go to step 3. Refer to the paragraph about the
indicator when it does not react
when shifted from 2H to 4H.
After taking the remedy, trace
this chart from the beginning.
3 Shift to 2H.
Can be shifted to 2H and then to
4H? Go to step 4. Refer to the paragraph about
shifting from 2H to 4H.
In particular, check if not at the
Check4WD condition, return to
this chart and trace it from the
beginning.
4 Set to N position in case of AT
and set to the neutral position in
case of MT and check if the
lamp blinks at 4Hz after
operation.
Failed T/M position switch and
harness (failure of TM1 and TM2
harness and their related
switches shown in the figure).
Incorrect wiring.
Repair as required and trace this
chart from the beginning. Shift back to 4H and go to step 5.
5 Start the engine and travel the
vehicle.
Does the speedometer run at
this time? Go to step 6. Failure of speed sensor or
disconnection or short of harness
(for the meter).
After repairing, trace this chart
from the beginning.
6 Check the harness between the
transfer controller and speed
sensor.
(Check the engine rotation
detection harness at the same
time.)
Is any trouble noticed? Failed harness between the
transfer controller and speed
sensor.
After repairing, trace this chart
from the beginning.
(Repair the engine rotation
detection unit, if required.) Go to step 7.
7 Travel the vehicle several
meters, stop it, meet the
permission requirements for
operation limits.
Did you wait for several seconds
after the requirements were
met? Failed controller.
Replace the controller and trace
this chart from the beginning. You did not wait for enough time.
Optimum waiting time is 1
second or maximum 3 minutes
depending on the previous
conditions.
Refer to the paragraph about
operation without failure.
*Before determining a trouble (Non-trouble mode)

TRANSFER CONTROL SYSTEM 7D1-49
From 4L to 4H: After the correction step 4-3(*), 4Lo indicator blinks at 4H.
Step Action Yes No
1 Is the ignition switch ON? Turn it OFF once. Go to step 2.
2 Turn ON the ignition switch and
check the valve. Do not start
the engine.
Has the valve check for 2
seconds been completed
normally? Go to step 3. Refer to the paragraph about the
indicator when it does not react
when shifted from 2H to 4H.
After taking the remedy, trace
this chart from the beginning.
3 Can be shifted to 2H and then to
4L? Go to step 4.
(Impossible usually.)
Failed controller In case of Check 4WD, shifting to
2H is possible.
Returning to 4L is impossible.
Refer to the paragraph about
Check4WD.
4 Set to N position in case of AT
and set to the neutral position in
case of MT and check if the
lamp blinks at 4Hz after
operation.
Failed T/M position switch and
harness (failure of TM1 and TM2
harness and their related
switches shown in the figure).
Incorrect wiring.
Repair as required and trace this
chart from the beginning. Press the operation switch of 4L
and go to step 5.
5 Start the engine and travel the
vehicle.
Does the speedometer run at
this time? Go to step 6. Failure of speed sensor or
disconnection or short of harness
(for the meter).
After repairing, trace this chart
from the beginning.
6 Check the harness between the
transfer controller and speed
sensor.
(Check the engine rotation
detection harness at the same
time.)
Is any trouble noticed? Failed harness between the
transfer controller and speed
sensor.
After repairing, trace this chart
from the beginning.
(Repair the engine rotation
detection unit, if required.) Go to step 7.
7 Travel the vehicle several
meters, stop it, meet the
permission requirements for
operation limits.
Did you wait for several seconds
after the requirements were
met? Failed transfer controller.
Replace the controller and trace
this chart from the beginning. You did not wait for enough time.
Optimum waiting time is 1
second or maximum 3 minutes
depending on the previous
conditions.
Refer to the paragraph about
operation without failure.
*Before determining a trouble (Non-trouble mode)

7D1-50 TRANSFER CONTROL SYSTEM
To neutral: After the correction step 5-2(*), neutral indicator blinks at 4Hz.
Check the function between H and L according to the chart for 4L to 4H instead of check
for the requirements of neutral.
Step Action Yes No
1 Is the ignition switch ON? Turn it OFF once. Go to step 2.
2 Turn ON the ignition switch and
check the valve. Do not start the
engine.
Has the valve check for 2
seconds been completed
normally? Go to step 3. Refer to the paragraph about the
indicator when it does not react
when shifted from 2H to 4H
(7D1-37).
After taking the remedy, trace
this chart from the beginning.
3 Can be shifted to 2H and then to
4L? Go to step 4.
(Impossible usually.)
Failed controller Refer to the paragraph about
shifting from 2H to 4H.
In particular, check if not at the
Check4WD condition, return to
this chart and trace it from the
beginning.
In case of Check4WD, shifting to
2H is possible.
Returning to 4H is impossible.
Refer to the paragraph about
Check4WD.
4 Set to N position in case of AT
and set to the neutral position in
case of MT and check if the lamp
blinks at 4Hz after operation. Failed T/M position switch and
harness (failure of TM1 and TM2
harness and their related
switches shown in the figure).
Incorrect wiring.
Repair as required and trace this
chart from the beginning. Shift back to 4H and go to step 5.
5 Start the engine and travel the
vehicle.
Does the speedometer run at this
time? Go to step 6. Failure of speed sensor or
disconnection or short of harness
(for the meter).
After repairing, trace this chart
from the beginning.
6 Check the harness between the
transfer controller and speed
sensor.
(Check the engine rotation
detection harness at the same
time.)
Is any trouble noticed? Failed harness between the
transfer controller and speed
sensor.
After repairing, trace this chart
from the beginning.
(Repair the engine rotation
detection unit, if required.) Go to step 7.
7 Travel the vehicle several
meters, stop it, meet the
permission requirements for
operation limits.
Did you wait for several seconds
after the requirements were met? Failed controller.
Replace the controller and trace
this chart from the beginning. You did not wait for enough time.
Optimum waiting time is 1
second or maximum 3 minutes
depending on the previous
conditions.
Refer to the paragraph about
operation without failure.
*Before determining a trouble (Non-trouble mode)
For shifting to neutral, 2H and 4L switches should be kept pressed at the same time for 10 seconds.
For shifting from neutral to other position, 2H, 4H or 4L switch should be kept pressed for 10 seconds.
When shifting from neutral to other position, the lamp blinking at 2Hz indicates active condition.
When the lamp keeps blinking at 2Hz, follow the step for the case when the lamp keeps blinking at 2Hz when
shifting between positions.

7A3-14 ON-VEHICLE SERVICE (AW30 –40LE)

Measure Time Lag
1. Fully apply the parking brake.
2. Start the engine. Check idling speed (A/C OFF).
3. Shift the shift lever from “N" to “D" range. Using a
stopwatch, measure the time it takes from shifting
the lever until the shock is felt.
Time lag: Less than 0.7 seconds
4. In same manner, measure the time lag for “N"


“R".
Time lag: Less than 1.2 seconds
Evaluation
1. If “N" 
“ D" time lag is longer than specified:

Line pressure too low
 Forward clutch malfunction
 No.2 one-way clutch not operating properly
2. If “N" 
“ R" time lag is longer than specified:

Line pressure too low
 Direct clutch malfunction
 No.3 brake malfunction
3. If both time lag is longer than specified:

Line pressure too low

Hydraulic Test



RUW37ALH000201
Preparation

1. Warm up the transmission fluid.
2. Remove the transmission case test plug and mount the hydraulic pressure gauge.
Oil pressure gauge: J –29770 –A
NOTE: Perform the test at normal operation fluid
temperature (50 – 80 
C or 122 – 176 
F).

7A3-18 ON-VEHICLE SERVICE (AW30 –40LE)

“ L" Range Test
1. While running above 80 km/h (50 mph) in the “D"
range, release your foot from the accelerator pedal
and shift into the “L" range.
Then check to see that the 2 
1 downshift occurs at
the specified point shown on the automatic shift
diagram.



RUW37ASH000601
2. While running in the “L" range, check to see that
there is no upshift to 2nd gear.
3. While running in the “L" range, release the
accelerator pedal and check the engine braking
effect.
4. Check for abnormal noise during acceleration and deceleration.







RUW37ASH000701

“ R" Range Test
Shift into the “R" range and, while starting at full throttle,
check for slipping.




RUW37ASH000801
“ P" Range Test
Stop the vehicle on a grade (more than 9%) and afte
r
shifting into the “P" range, release the parking brake.
Then check to see that the parking lock pawl holds the
vehicle in place.

DIAGNOSIS (JR405E) 7A2-3
PAGE
No. B12: NOISE OR VIBRATION IS GENERATED AT STARTING..................................7A2-107
No. C1: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd........7A2-108
No. C2: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd.......7A2-108
No. C3: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th........7A2-108
No. C4: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN ................................7A2-108
OR KICK-DOWN TO 4th TO 3
rd.................................................................................7A2-108
No. C5: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 4th TO 2
nd..............................................................................................................................7A2-108
No. C6: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 3rd TO 2
nd.............................................................................................................................7A2-108
No. C7: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN TO 4th OR 3
rd
TO 1
st............................................................................................................................................7A2-108
No. C8: ENGINE RACE UP (SLIP) OTHERS.........................................................................7A2-108
No. C9: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd.........................7A2-111
No. C10: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd......................7A2-111
No. C11: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th.......................7A2-111
No. C12: LARGE SHOCK WHEN GEAR IS SHIFTED TO 1st TO 2
ND OR 2nd TO 1st..7A2-114
No. C13: LARGE SHOCK WHEN GEAR IS SHIFTED TO 2nd TO 3
rd OR 3rd TO 2nd.7A2-114
No. C14: LARGE SHOCK WHEN GEAR IS SHIFTED TO 3rd TO 4th TO 3
rd................7A2-114
No. C15: LARGE SHOCK WHEN KICK-DOWN....................................................................7A2-114
No. C16: LARGE SHOCK WHEN NO ACCELERATION.....................................................7A2-114
No. C17: LARGE SHOCK WHEN GEAR IS SHIFTED DOWN TO 2nd TO
1st IN L RANGE..........................................................................................................................7A2-114
No. C18: LARGE SHOCK (OTHER)........................................................................................7A2-114
No. C19: LARGE SHOCK WHEN VEHICLE SPEED IS DOWNED BY NO
ACCELERATOR PANEL OR VEHICLE IS STOPPED........................................................7A2-114
No. C20: LARGE LOCK-UP SHOCK.......................................................................................7A2-114
No. C21: SHIFT DOWN OR ENGINE OVER-RUN WHEN THE ACCELERATION
PANE IS STEPPED ON IN 4th GEAR....................................................................................7A2-114
NO. D1: FAULTY GEAR SHIFTING (DIFFERENT FROM SHIFT PATTERN)............... 7A2-115
NO. D2: GEAR IS SHIFTED FREQUENTLY ................................................................. 7A2-120

7A2-4 DIAGNOSIS (JR405E)
PAGE
NO. D3: GEAR SHIFT POINT IS LOW OR HIGH AT ALL POINT................................. 7A2-120
NO. D4: GEAR SHIFT POINT IS LOW OR HIGH AT LIMITED POINT ......................... 7A2-120
NO. D5: NO KICK-DOWN .............................................................................................. 7A2-120
NO. E1: NO GEAR SHIFT .............................................................................................. 7A2-121
NO. E2: ONLY 4TH GEAR (O/D) IS NOT SELECTABLE ............................................. 7A2-124
NO. E3: GEAR IS SHIFTED 2ND TO 3RD IN 2 RANGE ............................................... 7A2-126
NO. E4: GEAR IS SHIFTED 1ST TO 2ND IN L RANGE................................................ 7A2-126
NO. E5: GEAR IS SHIFTED 3RD TO 4TH IN 3 RANGE................................................ 7A2-126
NO. F1: LOW MAXIMUM SPEED OR POOR ACCELERATION ................................... 7A2-127
NO. F2: ENGINE RACES UP DURING ACCELERATION (SLIP) ................................. 7A2-130
NO. F3: NOISE OR VIBRATION DURING THE RUNNING IN R, D, 3, 2 OR L
RANGE .......................................................................................................................... 7A2-130
NO. F4: ENGINE BRAKE DOES NOT APPLY IN L RANGE......................................... 7A2-130
NO. F5: ENGINE STALLS BEFORE VEHICLE STOPS FROM RUNNING ................... 7A2-131
NO. G1: VEHICLE MOVES IN P RANGE OR PARKING GEAR IS NOT
DISENGAGED OTHER THAN P RANGE ..................................................................... 7A2-131
NO. G2: CREEP FORCE IS LARGE.............................................................................. 7A2-131
NO. G3: CREEP FORCE IS SMALL .............................................................................. 7A2-132
NO. G4: LARGE NOISE DURING IDLING WITH THE VEHICLE IN STOP STATE ...... 7A2-133
NO. H1: JUDDER OCCURS AT THE LOCK-UP ........................................................... 7A2-133
NO. H2: LARGE LOCK-UP SHOCK .............................................................................. 7A2-133
NO. H3: LOCK-UP POINT IS HIGH OR LOW ............................................................... 7A2-133
NO. I1: NO LOCK-UP .................................................................................................... 7A2-134
NO. J1: OIL LEAKS FROM BREATHER ....................................................................... 7A2-136
NO. J2: OIL LEAKS BETWEEN ENGINE AND CONVERTER HOUSING .................... 7A2-136
NO. J3: OIL LEAKS BETWEEN MAIN CASE AND CONVERTER HOUSING.............. 7A2-136
NO. J4: OIL LEAKS BETWEEN MAIN CASE AND REAR HOUSING .......................... 7A2-136
NO. J5: OIL LEAKS FROM OIL PAN ............................................................................ 7A2-136
NO. J6: OIL LEAKS FROM MANUAL SHAFT OIL SEAL ............................................. 7A2-136
NO. J7: OIL LEAKS FROM OIL COOLER PIPE JOINT................................................ 7A2-136
NO. Z1: TRANSMISSION OVERHEAT .......................................................................... 7A2-136
NO. Z2: MODE LAMP (POWER DRIVE OR 3RD START) DOES NOT LIGHT UP
WHEN THE POWER MODE OR 3RD START MODE IS TURNED ON........................ 7A2-137

DIAGNOSIS (JR405E) 7A2-31
CONNECTOR LIST
TCM
No. Connector face No. Connector face
B-23
Green
Meter-A B-73

SilverWeld splice 3 (Earth)
B-24
Green
Meter-B C-2
SilverEngine room-RH ground
B-50
White
Power/3rd start switch C-44
WhiteStop lamp switch
B-54
White
J/B I2 C-56
(4JH1-TC)
ECM-A
B-56
White
J/B I4 C-57
(4JH1-TC)
ECM-B
B-58
Black
Check connector C-94
(6VE1)
(4JH1-TC)
Gray TCM
B-62
White
Ignition switch (IGSUB : G1) C-95
(6VE1)
(4JH1-TC)
WhiteTCM
B-63
White
Ignition switch (IGSUB : G2) C-107
WhiteJ/B E2
B-64
Silver
Weld splice 1 (Illumination) C-109
SilverBody-LH ; ground
B-68
(4JH1TC,
6VE1)
White Immobilizer C/U E-10

SilverEngine; ground

DIAGNOSIS (JR405E) 7A2-79

Step Action Yes No
1 Turn the key switch on and check the DTC. Is only the DTC for
low & reverse brake fail-safe valve failure outputted?
Go to Step 2
Go to Other DTC
Section
2 Clear the DTC from the memory. Turn the key switch off once,
and then start the engine. Does the CHECK TRANS blink
when the D range is selected and about 10 seconds elapsed?
Go to Other DTC
Section Go to Step 3
3 Run the vehicle, shift the gear from 1st to 4th, stop the vehicle,
and again shift the gear from 1st to 4th. Does the CHECK
TRANS blink at this time?
Go to Step 4
The low & reverse
brake fail-safe valve
may be faulty
temporarily.
Go to step 5
4 Turn the key switch on and check the DTC. Is only the DTC for
the low & reverse brake fail-safe valve failure outputted?
Repair or replace the
control valve.
Go to Step 5
Go to Other DTC
Section
5 Clear the DTC from the memory and perform the work after
repair. Is the same DTC code outputted again in the
subsequent DTC check?
Replace the TCM Go to Step 6
6 Are the other DTCs outputted?
Go to Other DTC
Section Action is completed

DIAGNOSIS (JR405E) 7A2-81

Step Action Yes No
1 Turn the key switch on and check the DTC. Is only the DTC for
2-4 brake fail-safe valve failure outputted?
Go to Step 2
Go to Other DTC
Section
2 Clear the DTC from the memory. Turn the key switch off once,
and then start the engine. Does the CHECK TRANS blink when
the D range is selected and about 10 seconds elapsed?
Go to Other DTC
Section Go to Step 3
3 Run the vehicle, shift the gear from 1st to 4th, stop the vehicle,
and again shift the gear from 1st to 4th. Does the CHECK
TRANS blink at this time?
Go to Step 4
The 2-4 brake fail-safe
valve may be faulty
temporarily.
Go to step 5
4 Turn the key switch on and check the DTC. Is only the DTC for
the 2-4 brake fail-safe valve failure outputted?
Repair or replace the
control valve.
Go to Step 5
Go to Other DTC
Section
5 Clear the DTC from the memory and perform the work after
repair. Is the same DTC code outputted again in the
subsequent DTC check?
Replace the TCM Go to Step 6
6 Are the other DTCs outputted?
Go to Other DTC
Section Action is completed