engine ISUZU TF SERIES 2004 Workshop Manual

ENGINE MECHANICAL (6VE1 3.5L) 6A-93
Main Data and Specification

General Specification
Item Specifications
Engine type, number of cylinders and arrangement Water cooled, four cycle V6
Form of combustion chamber Pent-roof type
Valve mechanism 4-Cams, 4-Valves, DOHC Gear & Belt Drive
Cylinder liner type Casted in cylinder block
Total piston displacement 3494 cc
Cylinder bore x stroke 93.4mm x 85.0mm

(3.6772 in  3.3465 in)
Compression ratio 8.6
Compression pressure at 300rpm 1.37 MPa (14.0 Kg/cm2)
Engine idling speed rpm Non adjustable (750)
Valve clearance Intake: 0.28 mm (0.11 in)

Exhaust: 0.30mm (0.12 in)
Oil capacity 5.3 liters
Ignition timing
Non adjustable (12 BTDC at idle rpm)
Spark plug PK16PR11, RC10PYP4, K16PR-P11
Plug gap 1.0 mm – 1.1 mm (0.0394 in – 0.0433 in)

6A-94 ENGINE MECHANICAL (6VE1 3.5L)
Torque Specifications
Ignition coil, Spark plug, Crankshaft angle sensor and Under cover
N
 m (kg
 m/ lb ft)







RTW460LF000101

ENGINE MECHANICAL (6VE1 3.5L) 6A-95
Cylinder head cover, Cylinder head, Camshaft bracket, Common chamber, ECM
N
 m (kg
 m/ lb ft)





RTW46ALF000601

6A-96 ENGINE MECHANICAL (6VE1 3.5L)
Crankshaft main bearing, Flywheel, Crankcase, Oil pan, Timing belt tensioner, Timing pulley, timing belt
cover, Oil pump, Oil gallery, Oil strainer and water pump
N
 m (kg
 m/ lb ft)




RTW46ALF000701

ENGINE MECHANICAL (6VE1 3.5L) 6A-97
Connecting rod and Water pump
N
 m (kg
 m/ lb ft)




E06RW042

6A-98 ENGINE MECHANICAL (6VE1 3.5L)
Engine mount
N
 m (kg
 m/ lb ft)








RTW36ALF000101

ENGINE MECHANICAL (6VE1 3.5L) 6A-99
Special Tool
ILLUSTRATION PART NO.
PART NAME
ILLUSTRATION PART NO.
PART NAME

5-8840-0011-0
(J-21687-02)
Remover; tie rod end 5-8840-2445-0
(J-42985)
Installer; Camshaft
oil seal

5-8840-0203-0
(J-36390)
Wrench; Oil filter (79) 5-8840-2545-0
(J-39206)
Installer; Pilot bearing

5-8840-2446-0
(J-8062)
Compressor;
Valve spring (1)
5-8840-2547-0
(J-42898)
Adapter; Compressor,
Valve spring (2) 5-8840-0133-0
(J-8614-01)
Holder; Crankshaft

5-8840-0623-0
(J-37281)
Remover; Oil controller 5-8840-2153-0
(J-37228)
Seal cutter

5-8840-0624-0
(J-38537)
Installer; Oil controller 5-8840-2286-0
(J-39201)
Installer; Real oil seal

5-8840-2005-0
(J-29107)
Universal pitman arm
remover 5-8840-2287-0
(J-39202)
Installer; Oil pump
oil seal

6A-100 ENGINE MECHANICAL (6VE1 3.5L)

ILLUSTRATION PART NO.
PART NAME


9-8511-4209-0
(J-24239-1)
Cylinder head bolt wrench





5-8840-2442-0
(J-42899)
Replacer; Valve guide (1,2)
5-8840-2548-0
(J-42687)
Installer; Valve guide (1)
5-8840-2549-0
(J-37985-1)
Remover; Valve guide (2)




5-8840-2444-0
(J-42689)
Adjusting Tool; Valve
clearance




5-8840-2443-0
(J-42686)
Lever; Gear spring




5-8840-2447-1
(J-43041)
Holder; Universal

ENGINE COOLING (6VE1 3.5L) 6B-1
ENGINE
ENGINE COOLING (6VE1 3.5L)
CONTENTS

Service Precaution............................................. 6B–1
General Description ........................................... 6B–2
Diagnosis ........................................................... 6B–5
Draining and Refilling Cooling System .............. 6B–6
Water Pump ...................................................... 6B–7
Water Pump and Associated Parts ................ 6B–7
Removal ......................................................... 6B–7
Inspection ....................................................... 6B–7
Installation....................................................... 6B–7
Thermostat ........................................................ 6B–9
Thermostat and Associated Parts .................. 6B–9
Removal ......................................................... 6B–9
Inspection ....................................................... 6B–9

Installation ...................................................... 6B–9
Radiator ............................................................. 6B–10
Radiator and Associated Parts ....................... 6B–10
Removal ......................................................... 6B–11
Inspection ....................................................... 6B–11
Installation ...................................................... 6B–12
Drive Belt and Cooling Fan ................................ 6B–15
Drive Belt and Associated Parts ..................... 6B–15
Inspection ....................................................... 6B–15
Installation ...................................................... 6B–15
Main Data and Specifications ............................ 6B–16
Special Tool .................................................... 6B–18


Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.

CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

6B-2 ENGINE COOLING (6VE1 3.5L)
General Description



030RW001
Legend (7)Cylinder Head
(1) Water Pump (8) Right Bank
(2) Thermostat (9) Throttle Body
(3) Radiator (10) Cylinder Block
(4) Reserve Tank (11) Cylinder Head
(5) Cooling Fan (12) Left Bank
(6) Cylinder Block (13) Heater


The engine cooling system consists of the radiator, the
water pump, the cooling fan, and the thermostat.
To quickly increase cold engine coolant temperature fo
r
smooth engine operation, the coolant is circulated by
the water pump and thermostat through the bypass
hose and back to the cylinder body.
The coolant does not circulate through the radiator.
When the coolant temperature reaches specified value,
the thermostat will begin to open and a gradually
increasing amount of coolant will circulate through the
radiator.
The thermostat will be fully open when the coolan
t
temperature reaches specified value. All of the coolant
is now circulating through the radiator for effective
engine cooling.