change wheel ISUZU TF SERIES 2004 Workshop Manual

ISUZU TF SERIES 2004 Workshop Manual TF SERIES 2004 ISUZU ISUZU https://www.carmanualsonline.info/img/61/57180/w960_57180-0.png ISUZU TF SERIES 2004 Workshop Manual

Page 256 of 4264

ISUZU TF SERIES 2004  Workshop Manual 4C1-36  FRONT WHEEL DRIVE 
  
 (5) 
After the ZERO setting is obtained, rotate the gaging arbor
until the dial indicator rod does not touch the gaging plate. 
  Record the number the dial indicator ne

Page 335 of 4264

ISUZU TF SERIES 2004  Workshop Manual BRAKE CONTROL SYSTEM   5A-19
 
System Components 
Electronic Hydraulic Control Unit (EHCU), four Wheel 
Speed Sensors, two Warning Lamps, and G-sensor. 
 
Electronic Hydraulic Control Unit (EHCU)
 
Th

Page 336 of 4264

ISUZU TF SERIES 2004  Workshop Manual 5A-20   BRAKE CONTROL SYSTEM
 
Electronic Brake-force Distribution (EBD) System
 
ABS has the EBD function. EBD is a function which 
controls braking force distribution of a front wheel and a 
rear wh

Page 342 of 4264

ISUZU TF SERIES 2004  Workshop Manual 5A-26   BRAKE CONTROL SYSTEM
 
DATA LIST (Tech 2) 
The data displayed by DATA LIST are as follows:  
 
 
Strings Units  Description 2WD 4WD
Front Left Wheel Speed   km/h (MPH)   
Front Right Wheel Spe

Page 446 of 4264

ISUZU TF SERIES 2004  Workshop Manual 5C-20  BRAKES
 
  

  Operation 
 
The operation of the P-valve by the master cylinde
r 
pressure is unchanged up to the brake points 
A and B. 
  If master cylinder fluid pressure penetrates into

Page 448 of 4264

ISUZU TF SERIES 2004  Workshop Manual 5C-22  BRAKES
 
 RTW35CSH001001 
 
 
  Operation 
1) Outline 
  When the LSPV (Load Sensing Proportioning Valve) 
detects a change in load weight, the load sensing spring
stretches. 
  Its reactio

Page 811 of 4264

ISUZU TF SERIES 2004  Workshop Manual ELECTRICAL-BODY AND CHASSIS  8A-153 
 
 HEADLIGHT LEVELING SWITCH 
Incorrect beam angle due to load change can be corrected. 
A four position switch, 0-3, can alter the beam angle through 
1.7 degrees

Page 1310 of 4264

ISUZU TF SERIES 2004  Workshop Manual 6C – 10   FUEL SYSTEM 
 Removal 
CAUTION:  When repair to the fuel system has been 
completed, start engine and check the fuel system for 
loose connection or leakage. For the fuel system 
diagnosis

Page 1438 of 4264

ISUZU TF SERIES 2004  Workshop Manual 6E–66 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
Throttle Position Sensor (TPS)
The TPS is a potentiometer connected to throttle shaft
on the throttle body. It is installed to the main TPS and
idle

Page 1954 of 4264

ISUZU TF SERIES 2004  Workshop Manual 6C-12  ENGINE FUEL (6VE1 3.5L) 
Removal 
CAUTION:  When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagno
Page:   1-10 11-20 21-30 next >