transmission oil ISUZU TF SERIES 2004 Workshop Manual

ISUZU TF SERIES 2004 Workshop Manual TF SERIES 2004 ISUZU ISUZU https://www.carmanualsonline.info/img/61/57180/w960_57180-0.png ISUZU TF SERIES 2004 Workshop Manual

Page 146 of 4264

ISUZU TF SERIES 2004  Workshop Manual 4A-10  PROPELLER SHAFT 
Diagnosis of Propeller Shaft and  
Universal Joint 
 
Condition Possible cause Correction 
Rough surface on splined yoke; 
burred nicked or worn. Replace the seal. Minor burrs

Page 147 of 4264

ISUZU TF SERIES 2004  Workshop Manual PROPELLER SHAFT  4A-11 
Removal and Installation 
 
 401RS023 
 Removal 
1. Raise the vehicle on a hoist. 
NOTE: 
Apply alignment marks on the flange at the rear 
propeller shaft both front and rear s

Page 223 of 4264

ISUZU TF SERIES 2004  Workshop Manual FRONT WHEEL DRIVE  4C1-3 
MAIN DATA AND SPECIFICATIONS 
FRONT AXLE AND DIFFERENTIAL 
Ring gear size mm (in)  194 (7.6) 
Axle tube   
Type  It consists of the duce, a cast iron housing and the Axle tub

Page 632 of 4264

ISUZU TF SERIES 2004  Workshop Manual 7C-30  CLUTCH 
  
 
 Shift Fork 
1. Visually inspect the surfaces of the shift fork making contact
with the release bearing for excessive wear and damage. 
2.  Remove any minor stepping or abrasion fr

Page 645 of 4264

ISUZU TF SERIES 2004  Workshop Manual CLUTCH  7C-43
 
1.  CLUTCH SLIPPAGE 
 
Checkpoint 
 Trouble Cause 
 Countermeasure 
 
 
Adjust the push rod play 
  
No push rod play in the master 
cylinder 
  NG    
Clutch pedal free play 
 
Clean

Page 649 of 4264

ISUZU TF SERIES 2004  Workshop Manual CLUTCH  7C-47
 
3.  CLUTCH SHUDDER 
 
Checkpoint 
 Trouble Cause 
 Countermeasure 
 
Grease or oil adhering to the
facing
Clean the related parts and/or
replace the facing
Replace the transmission fro

Page 1089 of 4264

ISUZU TF SERIES 2004  Workshop Manual ELECTRICAL-BODY AND CHASSIS  8A-431 
 
 
No.  Connector face  No.  Connector face 
E-71 
 
 NOT USED E-80 
(6VE1)
 Cylinder revolution 
E-72 
(C24SE) 
(6VE1) 
 Engine earth-A E-81 
(6VE1)
 Speed senso

Page 1181 of 4264

ISUZU TF SERIES 2004  Workshop Manual ENGINE MECHANICAL   6A – 41 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Coolant Replenishment 
Warning: 
When the coolant is heated to a high

Page 1296 of 4264

ISUZU TF SERIES 2004  Workshop Manual 6B  – 16   ENGINE COOLING 
 
P1010064 
Removal 
1.  Disconnect battery ground cable.  
2.  Loosen a drain plug to drain EC. 
3.  Disconnect oil cooler hose on automatic transmission (A/T).
4. Discon

Page 1298 of 4264

ISUZU TF SERIES 2004  Workshop Manual 6B – 18  ENGINE COOLING 
  
 
 
 
110RS005 
 
 Check the rubber hoses for swelling. 
 
Installation 
1.  Install radiator assembly (9) with hose, taking care not to
damage the radiator core with a
Page:   1-10 11-20 21-30 31-40 41-50 ... 170 next >